Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY (for Dynamic Torque Control AWD)
RM37A0E _52 Drivetrain _086863 AXLE AND DIFFERENTIAL _0421148 REAR DIFFERENTIAL CARRIER ASSEMBLY(for Dynamic Torque Control AWD) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for Dynamic Torque Control AWD)  INSTALLATION  


PROCEDURE

Hide 41196 1.INSTALL REAR DIFFERENTIAL DYNAMIC DAMPER

a.

Install the rear differential dynamic damper to the rear No. 2 differential support with a new bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 52380C 2.TEMPORARILY INSTALL REAR NO. 2 DIFFERENTIAL SUPPORT

a.
C429329N01
0.521,0.927 0.677,1.125 0.156,0.198 10 false A 2.906,0.906 3.063,1.104 0.156,0.198 10 true A

Temporarily install the rear No. 2 differential support to the rear differential carrier assembly with 2 new bolts and 2 new nuts.

NOTICE:
·

Be sure to install the rear No. 2 differential support facing the direction shown in the illustration.

·

Be sure to install the tabs of each nut to the positions (A) shown in the illustration.



HINT:

The nuts have tabs to prevent them from rotating.



b.

Install the 2 rear upper differential mount stoppers to the rear No. 2 differential support.


Hide 52391B 3.INSTALL DIFFERENTIAL SUPPORT

a.
C429328N01
1.26,0.271 1.427,0.469 0.167,0.198 10 true A

Install the differential support to the rear differential carrier assembly with 3 new bolts.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

HINT:

Tighten the bolt (A) shown in the illustration first.



Hide 41110 4.INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY

NOTICE:
·

Do not damage the contact surface when installing the rear differential carrier assembly.

·

Securely support the rear differential carrier assembly while performing this step to avoid excessively tilting or dropping the rear differential carrier assembly.

·

Install the bolts and nuts with the rear differential carrier assembly secured.



a.

Support the rear differential carrier assembly with a transmission jack using 2 attachments or equivalent tools as shown in the illustration.


b.

Temporarily install the rear differential carrier assembly to the rear suspension member sub-assembly with the 2 rear lower differential mount stoppers, 2 new bolts (A), 2 new bolts (C) and 2 new nuts.

C429350C02
3.74,2.115 3.927,2.771 3.927,2.771 3.469,1.865 true 3.885,2.771 4.135,2.969 0.25,0.198 10 true *a 2.552,2.021 2.719,2.188 0.167,0.167 10 true C 4.646,1.594 4.833,1.792 0.188,0.198 10 true C 0.813,2.396 0.979,2.563 0.167,0.167 10 true A 0.833,2.667 1,2.833 0.167,0.167 10 true A 3.521,2.385 3.688,2.552 0.167,0.167 10 true B 4.146,2.156 4.333,2.354 0.188,0.198 10 true B
*a Attachment - -
V100155

Attachment Installation Position - -



c.

Tighten the 2 bolts (A).

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)

NOTICE:

Do not tighten the bolts with the inner cylinder or rear No. 1 differential mount cushion tilted.



d.

Tighten the 2 bolts (B).

Torque:
82 N*m (836 kgf*cm, 60 ft.*lbf)


e.

Tighten the 2 bolts (C).

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)

NOTICE:

Do not tighten the bolts with the inner cylinder or rear differential mount cushion tilted.



f.

Engage the clamp to install the frame wire.


g.

Connect the 2 connectors and breather tube.


Hide 48812 5.INSTALL REAR STABILIZER BAR

Hide 6.INSTALL REAR DRIVE SHAFT ASSEMBLY

a.

Hide 37100 7.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 8.ADD DIFFERENTIAL OIL

Hide 9.INSPECT FOR DIFFERENTIAL OIL LEAK

Hide 10. DYNAMIC TORQUE CONTROL AWD SYSTEM CALIBRATION