Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _094408 STOP AND START _0444545 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Stop and Start Priority Control System  


DESCRIPTION

In stop and start control status, there is normal status (Standard) and stop and start priority status (Extended).

Stop and start control status can be switched to the desired mode by pressing and holding the stop and start system cancel switch (ecorun cancel switch assembly), or by operating the steering pad switch assembly, and the mode change is also shown on the multi-information display screen.

When the mode has been switched by pressing and holding the stop and start system cancel switch (ecorun cancel switch assembly), a signal is sent directly from the stop and start system cancel switch (ecorun cancel switch assembly) to the engine stop and start ECU.

When the steering pad switch assembly is used to select a control mode, a status change request signal is sent from the combination meter assembly to the engine stop and start ECU via CAN communication.

Cooperative control is performed by the air conditioning amplifier assembly and engine stop and start ECU based on the selected control mode.

When stop and start priority control (Extended) is selected, the operation time of stop and start control will be extended in order to improve fuel economy.

WIRING DIAGRAM

A459795E02
1.313,4.115 1.771,4.313 0.458,0.198 10 false +DP 2.146,4.115 2.604,4.313 0.458,0.198 10 false EAU 0.479,4.115 0.938,4.313 0.458,0.198 10 false +DP2 0.375,4.625 0.833,4.823 0.458,0.198 10 false z1 1.219,4.615 1.677,4.813 0.458,0.198 10 false z1 2.042,4.615 2.5,4.813 0.458,0.198 10 false z1 2.375,4.604 2.833,4.802 0.458,0.198 10 false 10 1.573,4.615 2.031,4.813 0.458,0.198 10 false 4 0.729,4.615 1.188,4.813 0.458,0.198 10 false 5 0.323,3.885 0.781,4.083 0.458,0.198 10 false H24 1.177,3.885 1.635,4.083 0.458,0.198 10 false H24 2,3.885 2.458,4.083 0.458,0.198 10 false H24 0.656,6.385 2.583,6.646 1.927,0.26 10 false : CAN Communication Line 0.375,5.365 2.333,5.625 1.958,0.26 10 false Steering Pad Switch Assembly 2.594,4.271 4.604,4.542 2.01,0.271 10 false Spiral Cable Sub-assembly 2.167,3.656 2.625,3.854 0.458,0.198 10 false 4 1.333,3.646 1.792,3.844 0.458,0.198 10 false 11 0.469,3.656 0.927,3.854 0.458,0.198 10 false 10 2.5,0.458 2.958,0.656 0.458,0.198 10 false MSM+ 2.5,0.823 2.958,1.021 0.458,0.198 10 false MSTI 2.24,0.729 2.698,0.927 0.458,0.198 10 false 29 2.24,0.375 2.698,0.573 0.458,0.198 10 false 28 3.427,0.531 3.885,0.729 0.458,0.198 10 false CANH 5.146,0.531 5.604,0.729 0.458,0.198 10 false CANH 5.135,2.906 5.594,3.104 0.458,0.198 10 false CANH 5.146,0.708 5.604,0.906 0.458,0.198 10 false CANL 3.427,0.708 3.885,0.906 0.458,0.198 10 false CANL 5.135,3.073 5.594,3.271 0.458,0.198 10 false CANL 2.333,1.219 2.792,1.417 0.458,0.198 10 false H21 2.333,1.385 4.26,1.646 1.927,0.26 10 false Combination Meter Assembly 5.083,1.219 6.646,1.781 1.563,0.563 10 false Air Conditioning Amplifier Assembly 4.875,3.5 5.333,3.698 0.458,0.198 10 false H66 4.875,3.667 6.771,3.948 1.896,0.281 10 false Engine Stop and Start ECU 4.219,5.615 4.677,5.813 0.458,0.198 10 false P7 4.208,5.792 7.115,6.458 2.906,0.667 10 false Stop and Start System Cancel Switch (Ecorun Cancel Switch Assembly) 6.01,5.125 6.469,5.323 0.458,0.198 10 false ECU 6.073,2.979 6.531,3.177 0.458,0.198 10 false ECAN 6.552,2.885 7.01,3.083 0.458,0.198 10 false 5 6.375,5.125 6.833,5.323 0.458,0.198 10 false 5 5.167,5.125 5.625,5.323 0.458,0.198 10 false 2 5.333,5.125 5.792,5.323 0.458,0.198 10 false GND 2.521,2.594 4.229,3.104 1.708,0.51 10 false Radio and Display Receiver Assembly 2.51,2.01 2.969,2.208 0.458,0.198 10 false SWG 2.271,1.917 2.729,2.115 0.458,0.198 10 false 24 2.521,2.427 3.063,2.625 0.542,0.198 10 false H1 1.167,4.833 1.781,5.031 0.615,0.198 10 false +DP 0.281,4.854 0.896,5.052 0.615,0.198 10 false +DP2 1.99,4.833 2.448,5.031 0.458,0.198 10 false EAU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

When stop and start priority control (Extended) is selected, the operation of the air conditioning system is limited. If the customer reports that the cooling effectiveness of the air conditioning system is poor, check the selected control mode. If stop and start priority control (Extended) is selected, cancel the control mode and check if the cooling effectiveness of the air conditioning system improves. If it improves, explain to the customer that the operation of the air conditioning system was limited by stop and start control.

·

Depending on the vehicle conditions, the stop and start operation time may not change even if stop and start priority control (Extended) is selected.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Check the problem symptoms.

HINT:
·

Check each symptom by checking the suspected areas in the table below.

·

By using the GTS and entering the following menus, the selected mode can be confirmed.

Powertrain / Stop and Start / Data List / Stop & Start A/C Mode



Result:
Problem Symptoms Trouble Area Proceed to
Multi-information display screen does not change after pressing steering pad switch assembly
·

Steering pad switch assembly

·

Spiral cable sub-assembly

·

Combination meter assembly

·

Engine stop and start ECU

·

Wire harness or connector (steering pad switch assembly - combination meter assembly or radio and display receiver assembly)

·

CAN communication system


A
When the stop and start system cancel switch (ecorun cancel switch assembly) is pressed and held, the status change interrupt display in the combination meter assembly is not displayed, and control does not change
·

Stop and start system cancel switch (ecorun cancel switch assembly)

·

Engine stop and start ECU

·

Wire harness or connector (stop and start system cancel switch (ecorun cancel switch assembly) - engine stop and start ECU)


B
Even though the stop and start system cancel switch (ecorun cancel switch assembly) and steering pad switch assembly are operated, the multi-information display screen does not change, and control does not change
·

Engine stop and start ECU

·

CAN communication system


C
Multi-information display screen changes without pressing steering pad switch assembly
·

Steering pad switch assembly

·

Spiral cable sub-assembly

·

Wire harness or connector (steering pad switch assembly - combination meter assembly or radio and display receiver assembly)


D
The status change interrupt display in the combination meter assembly is not displayed, but control changes Combination meter assembly E
The status change interrupt display in the combination meter assembly is displayed, but control does not change
·

Air conditioning amplifier assembly

·

CAN communication system


F
Control mode returns to default mode after turning ignition switch ON Engine stop and start ECU G




A

2.CHECK OPERATION

B

C

3.CHECK DTC OUTPUT

D

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY OR RADIO AND DISPLAY RECEIVER ASSEMBLY)

E

F

7.CHECK DTC OUTPUT

G

8.CHECK DTC OUTPUT
2.CHECK OPERATION
a.

Using the steering pad switch assembly, check that all functions other than "Stop & Start Settings" can be selected.

Result:
Result Proceed to
Only "Stop & Start Settings" cannot be selected A
No function can be selected using the steering pad switch assembly B




A

3.CHECK DTC OUTPUT

B

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY OR RADIO AND DISPLAY RECEIVER ASSEMBLY)
3.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

B

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY OR RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the spiral cable sub-assembly connector.


b.

Disconnect the combination meter assembly connector.


c.

Disconnect the radio and display receiver assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H24-11 (+DP) - H21-29 (MSTI) Always Below 1 Ω
H24-10 (+DP2) - H21-28 (MSM+) Always Below 1 Ω
H24-4 (EAU) - H1-24 (SWG) Always Below 1 Ω
H24-11 (+DP) or H21-29 (MSTI) - Body ground and other terminals Always 10 kΩ or higher
H24-10 (+DP2) or H21-28 (MSM+) - Body ground and other terminals Always 10 kΩ or higher
H24-4 (EAU) or H1-24 (SWG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.INSPECT STEERING PAD SWITCH ASSEMBLY

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

7.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

8.CHECK DTC OUTPUT
a.

Perform a road test.


b.

Read the DTCs.

Powertrain > Stop and Start > Trouble Codes
50001 392
Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

B