If the entry lock function does not operate for the driver door only, but the entry unlock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door)).
for LHD
for RHD
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
After repair, confirm that no DTCs are output.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check that the entry lock function.
| *a | Lock Sensor |
| *a | Lock Sensor |
Turn the ignition switch off.
Open and close the driver door.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.
If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.
When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*
*: w/ Wireless Door Lock Buzzer Answer-back Function
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
for HV Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CHECK FOR INTERMITTENT PROBLEMS
for Gasoline Model: Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>CHECK FOR INTERMITTENT PROBLEMS
| *a | Lock Sensor |
| *a | Lock Sensor |
Open and close the driver door.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Read the Data List according to the display on the GTS.
Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.
If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.
When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*
*: w/ Wireless Door Lock Buzzer Answer-back Function
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Trigger Switch | Driver door touch sensor (lock sensor) | OFF or ON | OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
| Tester Display |
|---|
| D-Door Trigger Switch |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the M5 certification ECU (smart key ECU assembly) connector.
Disconnect the J25*1 or J9*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-17 (CLG1) - J25-6 (ANT1) | Always | Below 1 Ω |
| M5-16 (CG1B) - J25-4 (ANT2) | Always | Below 1 Ω |
| M5-17 (CLG1) or J25-6 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-16 (CG1B) or J25-4 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-17 (CLG1) - J9-6 (ANT1) | Always | Below 1 Ω |
| M5-16 (CG1B) - J9-4 (ANT2) | Always | Below 1 Ω |
| M5-17 (CLG1) or J9-6 (ANT1) - Other terminals and body ground | Always | 10 kΩ or higher |
| M5-16 (CG1B) or J9-4 (ANT2) - Other terminals and body ground | Always | 10 kΩ or higher |
Reconnect the J25*1 or J9*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
Reconnect the M5 certification ECU (smart key ECU assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Lock Sensor |
| *a | Lock Sensor |
Open and close the driver door.
Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the driver door.
Read the Data List according to the display on the GTS.
Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.
If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.
When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*
*: w/ Wireless Door Lock Buzzer Answer-back Function
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Trigger Switch | Driver door touch sensor (lock sensor) | OFF or ON | OFF: Driver door touch sensor (lock sensor) not touched
ON: Driver door touch sensor (lock sensor) touched |
·
Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate. |
| Tester Display |
|---|
| D-Door Trigger Switch |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
| Proceed to |
|---|
| OK |
| NG |
OK
NG