The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
58441L
2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for 2GR-FKS:
Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
for A25A-FXS, A25B-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If an airbag deploys for any reason, it may cause a serious injury.
67492A
4.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the clip and guide to remove the front door lower frame bracket garnish.
5.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
|
Protective Tape |
Apply protective tape to the front door trim board sub-assembly as shown in the illustration.
Using a moulding remover, disengage the 2 clips, 4 claws and 5 guides as shown in the illustration.
Disconnect each connector to remove the multiplex network master switch assembly with front door upper armrest base panel.
6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
|
Protective Tape |
Apply protective tape to the front door trim board sub-assembly as shown in the illustration.
Using a moulding remover, disengage the 2 clips, 6 claws and 5 guides as shown in the illustration.
Disconnect the connector to remove the power window regulator switch assembly with front door upper armrest base panel.
69278B
7.REMOVE FRONT DOOR INSIDE HANDLE BEZEL
Using a moulding remover, disengage the 3 claws to remove the front door inside handle bezel as shown in the illustration.
81230N
8.REMOVE COURTESY LIGHT ASSEMBLY
67602
9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.
Remove the 3 screws.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 10 clips as shown in the illustration.
|
Remove in this Direction |
Disengage the 4 claws and guide as shown in the illustration.
w/ Illumination:
Disengage the clamp.
Disconnect the connector.
w/ Seat Memory Switch:
Disconnect the connector.
| *1 | Front Door Inside Lock/Unlock Knob Locking Cable |
| *2 | Front Door Lock Open Lever Remote Control Cable |
|
Remove in this Direction |
Disconnect the front door lock open lever remote control cable and front door inside lock/unlock knob locking cable as shown in the illustration to remove the front door trim board sub-assembly.
69206B
10.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 3 claws to remove the front door inside handle sub-assembly.
74038C
11.REMOVE DOOR ARMREST COVER SUB-ASSEMBLY
|
Remove in this Direction |
Disengage the claw to remove the door armrest cover sub-assembly as shown in the illustration.
84927
12.REMOVE SEAT MEMORY SWITCH (w/ Seat Memory Switch)
67664C
13.REMOVE DOOR FRAME GARNISH
|
Remove in this Direction |
Using a clip remover, disengage the clip.
Disengage the 2 guides to remove the door frame garnish as shown in the illustration.
89430
14.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Memory)
87964
15.REMOVE OUTER MIRROR INSTALL HOLE COVER
16.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
68172A
17.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
|
Remove in this Direction |
Remove the front door inner glass weatherstrip as shown in the illustration.
67838A
18.REMOVE FRONT DOOR VENT SEAL
|
Remove in this Direction |
Disengage the 3 guides to remove the front door vent seal from the front door inner glass weatherstrip as shown in the illustration.
67856D
19.REMOVE FRONT DOOR PANEL PROTECTOR
|
Remove in this Direction |
Remove the front door panel protector as shown in the illustration.
86160
20.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67869J
21.REMOVE FRONT DOOR WEATHERSTRIP CLIP
Turn each front door weatherstrip clip 45 degrees as shown in the illustration and remove the 3 front door weatherstrip clips.
67832
22.REMOVE FRONT DOOR SERVICE HOLE COVER
Disconnect the connector.
Disengage the 6 clamps.
Disengage the 5 clips and remove the front door service hole cover.
89860A
23.REMOVE SIDE AIRBAG SENSOR ASSEMBLY
68102
24.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
for Driver Side:
Connect the power window regulator master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
for Driver Side:
Disconnect the power window regulator master switch assembly.
for Front Passenger Side:
Disconnect the power window regulator switch assembly.
Remove the 2 bolts.
After the bolts are removed, do not allow the front door glass sub-assembly to fall.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass sub-assembly.
25.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
Disconnect the connector.
Remove the 7 nuts and front door window regulator assembly.
68151D
26.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67404F
27.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Remove in this Direction |
Remove the bolt.
Disengage the guide and remove the front door rear lower frame sub-assembly as shown in the illustration.
69220
28.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
Using a screwdriver, disengage the 2 claws as shown in the illustration.
Using a screwdriver, disconnect the connector.
Disengage the 2 claws and move the lever as shown in the illustration.
|
Remove in this Direction |
Remove the front door outside handle assembly as shown in the illustration.
29.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door lock cylinder assembly.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
69217D
30.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.
Disengage the 2 claws to remove the front door outside handle cover.
69241H
31.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 2 claws and guide to remove the front door front outside handle pad.
69242E
32.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD
Disengage the claw and 3 guides to remove the front door rear outside handle pad.
69040A
33.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69202A
34.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Disengage the clamp.
Using a T30 "TORX" socket wrench, remove the screw.
|
Remove in this Direction |
Disengage the claw and guide to remove the front door outside handle frame sub-assembly as shown in the illustration.
69312
35.REMOVE FRONT DOOR LOCK OPEN ROD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door lock open rod as shown in the illustration.
75720
36.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY
75756D
37.REMOVE FRONT DOOR WINDOW FRAME MOULDING
75754A
38.REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING
67496C
39.REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER
75792
40.REMOVE DOOR WINDOW FRAME MOULDING CLIP
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.
67001A
41.REMOVE FRONT DOOR PANEL CUSHION
Disengage the claw to remove the front door panel cushion.
42.REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY
75793
43.REMOVE FRONT DOOR UPPER OUTSIDE MOULDING PAD
67837B
44.REMOVE FRONT DOOR DUST PROOF SEAL
Disengage the 3 claws to remove the 3 front door dust proof seals.
68620
45.REMOVE FRONT DOOR CHECK ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt, 2 nuts and front door check assembly.
67862
46.REMOVE FRONT DOOR WEATHERSTRIP
Using a clip remover, disengage the 24 clips and remove the front door weatherstrip.