Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2020.11
RM37A0E _58 Vehicle Interior _086886 THEFT DETERRENT / KEYLESS ENTRY _0417748 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the entry lock function does not operate for the front passenger door only, but the entry unlock function operates, the request code is being transmitted properly from the for passenger door. In this case, there may be a problem related to the lock sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door)).

WIRING DIAGRAM

for LHD


B506722E49
1.333,0.781 1.948,0.979 0.615,0.198 10 false ANT1 1.333,1.927 1.948,2.125 0.615,0.198 10 false ANT2 1.792,0.781 2,1 0.208,0.219 10 false 6 1.792,1.927 1.948,2.125 0.156,0.198 10 false 4 0.167,2.51 1.344,2.781 1.177,0.271 10 false J9 5.25,0.771 5.865,0.969 0.615,0.198 10 false CLG2 5.25,1.927 5.865,2.125 0.615,0.198 10 false CG2B 5.073,2.552 5.396,2.781 0.323,0.229 10 false M5 4.99,0.771 5.198,0.99 0.208,0.219 10 false 15 4.99,1.917 5.292,2.156 0.302,0.24 10 false 14 0.958,1.469 1.115,1.667 0.156,0.198 10 false IC 5.813,1.458 5.969,1.656 0.156,0.198 10 false IC 0.167,2.656 2.458,3.083 2.292,0.427 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 5.083,2.698 6.646,3.167 1.563,0.469 10 false Certification ECU (Smart Key ECU Assembly)


for RHD


B592305E05
0.323,2.708 2.646,3.302 2.323,0.594 10 false Front Door Outside Handle Assembly (for Front Passenger Door) 0.323,2.542 0.688,2.802 0.365,0.26 10 false J25 1.781,0.771 2.021,1.01 0.24,0.24 10 false 6 1.792,1.917 2.031,2.156 0.24,0.24 10 false 4 1.323,0.771 1.688,1 0.365,0.229 10 false ANT1 1.313,1.917 1.677,2.146 0.365,0.229 10 false ANT2 5.26,0.781 5.729,1.031 0.469,0.25 10 false CLG2 5.26,1.917 5.729,2.167 0.469,0.25 10 false CG2B 4.99,0.771 5.229,1.01 0.24,0.24 10 false 15 5,1.917 5.313,2.188 0.313,0.271 10 false 14 5.031,2.708 6.563,3.469 1.531,0.76 10 false Certification ECU (Smart Key ECU Assembly) 5.042,2.542 5.469,2.781 0.427,0.24 10 false M5 5.813,1.406 6.281,1.656 0.469,0.25 10 false IC 0.99,1.406 1.458,1.656 0.469,0.25 10 false IC


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Entry Function) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK

OK:

Door locks operate normally.



Result:
Proceed to
OK
NG



OK

2.CHECK ENTRY OPERATION

NG

2.CHECK ENTRY OPERATION
a.

Check that the entry lock function.

i.
for LHD:
B560856C01
2.26,0.688 2.813,0.208 2.813,0.208 2.979,0.208 false 2.271,0.927 2.833,0.208 false 3.01,0.135 3.323,0.333 0.313,0.198 10 false *a
*a Lock Sensor


for RHD:
B560853C01
0.594,0.313 0.75,0.313 0.75,0.313 1.156,0.938 false 1.167,0.729 0.75,0.313 false 0.396,0.208 0.708,0.406 0.313,0.198 10 false *a
*a Lock Sensor


Turn the ignition switch off.


ii.

Open and close the front passenger door.


iii.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the front passenger door.


iv.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (1).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*

*: w/ Wireless Door Lock Buzzer Answer-back Function






Result:
Result Proceed to
Entry function does not operate normally A
Entry function operates normally B



A

3.READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)

B

3.READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)
a.
for LHD:
B560856C01
2.26,0.688 2.813,0.208 2.813,0.208 2.979,0.208 false 2.271,0.927 2.833,0.208 false 3.01,0.135 3.323,0.333 0.313,0.198 10 false *a
*a Lock Sensor


for RHD:
B560853C01
0.594,0.313 0.75,0.313 0.75,0.313 1.156,0.938 false 1.167,0.729 0.75,0.313 false 0.396,0.208 0.708,0.406 0.313,0.198 10 false *a
*a Lock Sensor


Open and close the front passenger door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the front passenger door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*

*: w/ Wireless Door Lock Buzzer Answer-back Function




Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Door Trigger Switch Front passenger door touch sensor (lock sensor) OFF or ON OFF: Front passenger door touch sensor (lock sensor) not touched
ON: Front passenger door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
P-Door Trigger Switch
50003 125 13
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR))
a.

Disconnect the M5 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the J9*1 or J25*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
M5-15 (CLG2) - J9-6 (ANT1) Always Below 1 Ω
M5-14 (CG2B) - J9-4 (ANT2) Always Below 1 Ω
M5-15 (CLG2) or J9-6 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
M5-14 (CG2B) or J9-4 (ANT2) - Other terminals and body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
M5-15 (CLG2) - J25-6 (ANT1) Always Below 1 Ω
M5-14 (CG2B) - J25-4 (ANT2) Always Below 1 Ω
M5-15 (CLG2) or J25-6 (ANT1) - Other terminals and body ground Always 10 kΩ or higher
M5-14 (CG2B) or J25-4 (ANT2) - Other terminals and body ground Always 10 kΩ or higher



d.

Reconnect the J9*1 or J25*2 front door outside handle assembly (for front passenger door) connector.

*1: for LHD

*2: for RHD



e.

Reconnect the M5 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (P-DOOR TRIGGER SWITCH)
a.
for LHD:
B560856C01
2.26,0.688 2.813,0.208 2.813,0.208 2.979,0.208 false 2.271,0.927 2.833,0.208 false 3.01,0.135 3.323,0.333 0.313,0.198 10 false *a
*a Lock Sensor


for RHD:
B560853C01
0.594,0.313 0.75,0.313 0.75,0.313 1.156,0.938 false 1.167,0.729 0.75,0.313 false 0.396,0.208 0.708,0.406 0.313,0.198 10 false *a
*a Lock Sensor


Open and close the front passenger door.


b.

Hold the electrical key transmitter sub-assembly at the same height as the door outside handle assembly and approximately 0.3 m (0.984 ft.) from the front passenger door.


c.

Read the Data List according to the display on the GTS.


d.

Touch the lock sensor of the front door outside handle assembly (groove on the front door outside handle) with 2 or more fingers for 2 seconds or more.

HINT:
·

If the door does not lock even when touching the lock sensor for 2 seconds or more, touch it with your palm.

·

When checking the operation of the lock sensor again, make sure to perform the procedure from step (a).

·

When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively.*

*: w/ Wireless Door Lock Buzzer Answer-back Function




Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P-Door Trigger Switch Front passenger door touch sensor (lock sensor) OFF or ON OFF: Front passenger door touch sensor (lock sensor) not touched
ON: Front passenger door touch sensor (lock sensor) touched
·

Displays whether the lock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily).

·

Use this Data List item to help determine if there is a lock sensor malfunction when the entry lock function does not operate.


Body Electrical > Entry&Start > Data List
Tester Display
P-Door Trigger Switch
50003 125 13
OK:

The GTS display changes correctly in response to the operation of the front door outside handle assembly (for front passenger door).



Result:
Proceed to
OK
NG



OK

END (CONNECTOR WAS NOT CONNECTED SECURELY)

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER DOOR)