Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.11
RM37A0E _51 Engine / Hybrid System _086906 A25A-FXS, A25B-FXS ENGINE MECHANICAL _0418984 ENGINE ASSEMBLY A

A25A-FXS, A25B-FXS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation.

*3: If the vehicle height has changed due to suspension or tire replacement

Auxiliary battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration DTC is output (Click here)
·

Replacement of engine assembly

·

Gas leak from exhaust system is repaired


Perform Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


for 2WD:(Click here)
for 4WD/AWD:(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Replacement of front bumper assembly*2
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Front television camera view adjustment Panoramic View Monitor System (Click here)
Replacement or removal and installation of 2 or more parts:
·

Front television camera assembly, radiator grille sub-assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment Panoramic View Monitor System (Click here)
Suspension, tires, etc.*3
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking Support Brake System (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking Assist Monitor System (Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic View Monitor System (Click here)
Front wheel alignment adjustment Perform "Calibration".
·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

CAUTION:
·
A346363C01
2.219,0.813 2.646,0.813 false 2.698,0.729 3.01,0.927 0.313,0.198 10 false *a
*a An Object Exceeding Weight Limit of Engine Lifter


The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.SECURE STEERING WHEEL

Hide 6.REMOVE FRONT WHEELS

Hide 53852B 7.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

a.
A456047

Remove the 4 screws and front wheel opening extension pad LH.


Hide 53851D 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

a.
A456046

Remove the 4 screws and front wheel opening extension pad RH.


Hide 51441 9.REMOVE NO. 1 ENGINE UNDER COVER

a.
A456045C01
0,0 0,0 false
V100135

Bolt
V100136

Screw


Remove the 3 bolts, 8 screws, 2 clips and No. 1 engine under cover.


Hide 51420 10.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

a.
A456050C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Remove the 2 bolts, 2 screws, 6 clips and No. 2 engine under cover assembly.


Hide 53737B 11.REMOVE FRONT FENDER APRON SEAL LH

a.
A456048

Remove the 2 bolts, clip and front fender apron seal LH.


Hide 53736 12.REMOVE FRONT FENDER APRON SEAL RH

a.
A456049

Remove the 2 bolts, clip and front fender apron seal RH.


Hide 13.REMOVE HEADLIGHT ASSEMBLY LH

Hide 52618 14.REMOVE FRONT BUMPER LOWER ABSORBER

Hide 52132A 15.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT

Hide 12601B 19.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A455183

Lift the front of the No. 1 engine cover sub-assembly to disengage the 2 clips, and then lift the rear of the No. 1 engine cover sub-assembly to disengage the clip and remove the No. 1 engine cover sub-assembly.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide G9200 20.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 23820 21.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.
A455186

Disengage the clamp.


b.

Disconnect the fuel vapor feed hose assembly from the No. 1 vacuum switching valve assembly.


Hide 87246B 22.DISCONNECT OUTLET HEATER WATER HOSE B

a.
A455189C01
1.688,1.635 1.844,1.635 1.844,1.635 2.083,1.396 true 1.375,1.531 1.667,1.771 0.292,0.24 10 true *a
*a Retainer
V113147

Pull out
V113148

Pull off


Pull out the retainer to disengage the lock claws and pull off the outlet heater water hose B from the No. 2 water by-pass pipe sub-assembly.


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected No. 2 water by-pass pipe sub-assembly and outlet heater water hose B connector with plastic bags to prevent damage and contamination.


Hide 87245B 23.DISCONNECT INLET HEATER WATER HOSE B

a.
A455190C01
1.219,1.771 1.427,1.771 1.427,1.771 1.563,1.375 true 0.917,1.656 1.198,1.865 0.281,0.208 10 true *a
*a Retainer
V113147

Pull out
V113148

Pull off


Pull out the retainer to disengage the lock claws and pull off the inlet heater water hose B from the flow shutting valve (water by-pass hose assembly).


b.

Check that there is no foreign matter on the sealing surfaces of the disconnected water lines. Clean them if necessary.


c.

Cover the disconnected flow shutting valve (water by-pass hose assembly) and inlet heater water hose B connector with plastic bags to prevent damage and contamination.


Hide 23901 24.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A455187

Remove the EFI fuel pipe clamp from the fuel tube connector.


b.

Disconnect the fuel tube sub-assembly.

i.
A455188

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION



Hide 16571C 25.DISCONNECT NO. 1 RADIATOR HOSE

a.
A455191

Disengage the clamp.


b.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 26.DISCONNECT NO. 2 RADIATOR HOSE

a.
A455192

Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly.


Hide 88703 27.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.
E431367

Remove the bolt and disconnect the discharge hose sub-assembly from the compressor with motor assembly.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.



Hide 88704 28.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide G9229A 29.DISCONNECT NO. 5 INVERTER COOLING HOSE

a.
A455193

Slide the clip and disconnect the No. 5 inverter cooling hose from the motor cooling cooler.


Hide 32930F 30.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE ASSEMBLY

a.
A455197C01
2.844,1.302 2.667,1.302 2.667,1.302 2.219,1.083 true 2.292,2.469 2.115,2.469 2.115,2.469 1.667,2.25 true 2.896,1.198 3.208,1.396 0.313,0.198 10 true *1 2.396,2.375 2.708,2.573 0.313,0.198 10 true *2
*1 Inlet Motor Hose
*2 Outlet Motor Hose


Disengage the clamp.


b.

Slide the clip and disconnect the inlet motor hose from the hybrid vehicle transaxle assembly.


c.

Slide the clip and disconnect the outlet motor hose from the hybrid vehicle transaxle assembly.


Hide 31.DISCONNECT WIRE HARNESS

HINT:

After disconnecting the wire harness, secure it with tape or equivalent to keep it out of the way.


a.
A455194

Disengage the 3 claws and remove the No. 1 relay block cover from the No. 1 engine room relay block and No. 1 junction block assembly.


b.
A455195

Remove the nut from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Disconnect the 4 connectors from the No. 1 engine room relay block and No. 1 junction block assembly.


d.

Using a screwdriver, disengage the claw and disconnect the wire harness from the No. 1 engine room relay block and No. 1 junction block assembly.


e.
A455196

Remove the 2 bolts and disconnect the earth wire.


Hide 16281N 32.DISCONNECT NO. 4 WATER BY-PASS HOSE

a.
A455185

Slide the clip and disconnect the No. 4 water by-pass hose from the No. 3 water by-pass pipe.


Hide 45220 33.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 58166A 34.REMOVE FRONT FLOOR COVER LH

a.
A455198C01
2.365,0.031 2.521,0.229 0.156,0.198 10 true A 1.563,0.49 1.719,0.688 0.156,0.198 10 true A 2.844,0.021 3,0.219 0.156,0.198 10 true B
V100135

Bolt
V100136

Screw
V100137

Clip


Remove the 5 bolts, 3 screws, 2 clips (A) and clip (B) and disengage the 5 clamps to remove the front floor cover LH from the vehicle body.


Hide 58165C 35.REMOVE FRONT FLOOR COVER RH

a.
A455199C01
0,0 0,0 false
V100135

Bolt
V100136

Screw
V100137

Clip


Remove the 3 bolts, 3 screws and clip and disengage the 4 clamps to remove the front floor cover RH from the vehicle body.


Hide 38.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.




b.
A455200

Remove the 3 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A455202

Remove the 4 bolts and engine mounting stay LH from the engine mounting insulator sub-assembly LH.


d.
A455201

Remove the 4 bolts and separate the engine mounting insulator sub-assembly LH from the hybrid vehicle transaxle assembly.


e.
A455204C01
0.854,0.094 1.01,0.292 0.156,0.198 10 true A 2.469,0.115 2.625,0.313 0.156,0.198 10 true A 0.115,2.365 0.271,2.563 0.156,0.198 10 true B 3.146,2.375 3.302,2.573 0.156,0.198 10 true B 0.417,3.74 0.573,3.938 0.156,0.198 10 true C 0.875,4.469 1.031,4.667 0.156,0.198 10 true C 1.365,3.99 1.521,4.188 0.156,0.198 10 true D 1.917,3.99 2.073,4.188 0.156,0.198 10 true D 2.854,3.708 3.01,3.906 0.156,0.198 10 true C 2.833,4.438 2.99,4.635 0.156,0.198 10 true C
V100135

Bolt
V100136

Nut


Remove the 2 bolts (A), 2 bolts (B) and 4 nuts and front bumper extension sub-assembly RH and front bumper extension sub-assembly LH from the front frame assembly and vehicle body.


f.

Remove the 4 bolts (C) and 2 bolts (D) and front suspension member brace rear RH and front suspension member brace rear LH from the front frame assembly and vehicle body.


g.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 23825 39.REMOVE FUEL DELIVERY GUARD

a.
A455205

Remove the bolt and fuel delivery guard from the engine mounting bracket RH.


Hide 40.INSTALL ENGINE HANGERS

a.
A455206C01
0.448,1.188 0.771,1.188 true 2.74,0.948 3.063,0.948 true 0.188,1.094 0.427,1.313 0.24,0.219 10 true *1 3.104,0.844 3.344,1.063 0.24,0.219 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 90105-A0354 or
91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 11361J 41.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A402190

Remove the flywheel housing under cover from the cylinder block sub-assembly.


Hide 45319 42.REMOVE STEERING GEAR HEAT INSULATOR (for LHD)

Hide 82121 43.REMOVE ENGINE WIRE

a.

Disconnect all clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 821H2 44.REMOVE HV AIR CONDITIONING WIRE

a.
A455210

Disengage the 2 clamps.


b.
A407267C02
1.167,0.563 1.417,0.302 1.417,0.302 1.573,0.302 true 1.625,0.229 1.938,0.427 0.313,0.198 10 false *a
*a Green-colored Lock
V100137

Slide


Using a screwdriver, slide the green-colored lock of the connector as shown in the illustration to release it and disconnect the connector.

CAUTION:

Make sure to wear insulated gloves.


NOTICE:

Insulate the disconnected terminals and connector with insulating tape.



c.
A455211

Remove the 2 bolts.


d.

Disengage the guide to remove the HV air conditioning wire from the hybrid vehicle transaxle assembly.


Hide 32930G 45.DISCONNECT NO. 2 TRANSMISSION OIL COOLER HOSE ASSEMBLY

Hide 35300B 46.REMOVE OIL PUMP WITH MOTOR ASSEMBLY

Hide 11363A 47.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 51100G 48.REMOVE FRONT FRAME ASSEMBLY

Hide 12361A 49.REMOVE FRONT ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the front engine mounting insulator is necessary.


a.
A455289

Remove the bolt and front engine mounting insulator from the front engine mounting bracket.


Hide 12371A 50.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.
A455208

Remove the bolt and wire harness clamp from the rear engine mounting insulator.


b.
A455209

Remove the bolt and rear engine mounting insulator from the rear engine mounting bracket.


Hide 30900 51.REMOVE HYBRID VEHICLE TRANSAXLE ASSEMBLY

Hide 31270 52.REMOVE TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 19315 54.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 55.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 56.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger from the cylinder head sub-assembly and engine mounting bracket RH.


Hide G92A0A 57.DISCONNECT INVERTER RESERVE TANK ASSEMBLY

a.
A455184C01
2.792,0.563 2.958,0.563 false 2.323,0.979 2.635,0.979 true 3.01,0.469 3.25,0.667 0.24,0.198 10 true *a 2.063,0.885 2.302,1.083 0.24,0.198 10 true *b
*a Pin
*b Grommet


Remove the 2 bolts.


b.

Disengage the pin and disconnect the inverter reserve tank assembly.


Hide 12305 58.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A455212

Remove the bolt and No. 1 inverter reserve tank bracket.


b.
A455213

Disengage the 2 clamps.


c.
A455214C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and disconnect the radiator reserve tank assembly.


d.
A455215

Remove the bolt and disconnect the No. 2 earth wire from the engine mounting insulator sub-assembly RH.


e.
A455216C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts and nut and remove the engine mounting insulator sub-assembly RH.


Hide 12341 59.REMOVE ENGINE MOUNTING SPACER

HINT:

Perform this procedure only when replacement of the engine mounting spacer is necessary.


a.
A455217

Remove the 2 bolts and engine mounting spacer from the vehicle body.


Hide 12306 60.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly LH is necessary.


a.
A455218C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, nut and the engine mounting insulator sub-assembly LH.