Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for Gasoline Model RHD) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0449072 BRAKE ACTUATOR(for Gasoline Model RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for Gasoline Model RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light (red) blinks when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.

Install the 3 brake actuator bracket cushions to the lower brake actuator bracket.


Hide 44521B 2.INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.

Install the 3 No. 2 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bracket cushion.



b.

Install the upper brake actuator bracket with the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C447481N01
1.396,1.635 1.521,1.833 0.125,0.198 10 true 1 0.969,0.74 1.094,0.938 0.125,0.198 10 true 2 2.313,1.292 2.438,1.49 0.125,0.198 10 true 3 1.958,1.042 2.094,1.208 0.135,0.167 10 true A

Temporarily install the brake actuator assembly to the brake actuator bracket assembly with the bolt (A).


b.

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·
C447709

Do not hold the brake actuator assembly by the connector.




Hide 4.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C447480N01
0.948,1.885 1.094,2.083 0.146,0.198 10 true 1 1.427,1.99 1.552,2.156 0.125,0.167 10 true 2 3.031,1.104 3.156,1.271 0.125,0.167 10 true 3

Install the brake actuator with bracket with the 2 bolts and nut in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Hold the brake actuator with bracket by the brake actuator assembly.



HINT:

Install the brake actuator with bracket while avoiding the brake lines.



b.
C447479

Engage the clamp to install a new brake tube clamp.


c.
C447478

Engage the clamp to connect the brake line.

NOTICE:

Do not kink or damage the brake line.



d.
C447476C01
0.99,0.135 1.323,0.135 1.323,0.135 1.573,0.5 true 1.927,0.635 2.208,0.302 2.208,0.302 2.458,0.302 true 2.469,0.833 2.635,0.583 2.635,0.583 2.969,0.583 true 2.083,1.844 2.083,1.427 true 1.156,1.302 1.49,1.052 true 1.583,1.385 1.667,0.969 true 3,0.49 3.188,0.667 0.188,0.177 10 true *a 2,1.854 2.188,2.042 0.188,0.188 10 true *b 0.958,1.24 1.135,1.417 0.177,0.177 10 true *c 1.49,1.406 1.667,1.573 0.177,0.167 10 true *d 0.813,0.052 0.979,0.229 0.167,0.177 10 true *e 2.5,0.198 2.667,0.365 0.167,0.167 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Disc Brake Cylinder Assembly LH
*d To Rear Disc Brake Cylinder Assembly RH
*e To Rear Disc Brake Cylinder Assembly LH
*f To Front Disc Brake Cylinder Assembly RH


Temporarily tighten the 6 brake lines to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




e.
C447484C01
2.74,2.646 2.74,2.979 false 1.865,2.969 2.177,3.125 0.313,0.156 10 false *a 2.688,3 3,3.156 0.313,0.156 10 false *b 1.521,1.583 1.667,1.75 0.146,0.167 10 true B 1.26,1.333 1.385,1.5 0.125,0.167 10 true A 2,1.135 2.146,1.302 0.146,0.167 10 true B 2.208,0.729 2.333,0.896 0.125,0.167 10 true A 1.5,0.417 1.625,0.583 0.125,0.167 10 true A 1.188,0.688 1.313,0.854 0.125,0.167 10 true A
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

for Specified Tightening Torque (A):

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

for Specified Tightening Torque (B):

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




f.
C447485C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the engine room main wire to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly.

·

Do not allow water, oil or dirt to enter the connector.




Hide 74404B 5.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 6.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

Hide 55704B 9.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 10.PERFORM INITIALIZATION AND CALIBRATION