This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
23100X
1.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY
When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.
Perform "Inspection After Repair" after replacing the fuel pump assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| *1 | Fuel Pump Assembly |
| *2 | Fuel Pump Lifter Assembly |
| *3 | No. 2 Camshaft |
| *a | Correct |
| *b | Incorrect |
Turn the crankshaft pulley until the flat of the No. 2 camshaft faces the fuel pump lifter assembly.
This prevents the No. 2 camshaft nose from pushing up the fuel pump lifter assembly when installing the fuel pump assembly.
| *1 | Fuel Pump Spacer Gasket |
| *a | Pump Drive Cam (Engine Oil Application Area) |
| *b | Fuel Pump Lifter Assembly (Engine Oil Application Area) |
Apply 30 cc (1.8 cu. in.) of engine oil to the pump drive cam.
Apply engine oil to the fuel pump lifter assembly.
Install a new fuel pump spacer gasket to the cylinder head cover sub-assembly and No. 4 camshaft bearing cap.
| *a | Fuel Pump Lifter Assembly (Engine Oil Application Area) |
| *b | Fuel Pump Lifter Guide (Engine Oil Application Area) |
| *c | Stopper Key |
| *d | Key Groove |
Apply engine oil to the inside of the fuel pump lifter guide and the outside of the fuel pump lifter assembly.
Set the fuel pump lifter assembly on the fuel pump lifter guide as shown in the illustration.
Align the stopper key of the fuel pump lifter assembly with the key groove of the fuel pump lifter guide.
Apply engine oil to a new O-ring and install it to the fuel pump assembly.
Do not damage the O-ring.
| *1 | Fuel Pump Assembly |
| *2 | Fuel Pump Flange |
Set the fuel pump flange and fuel pump assembly on the No. 4 camshaft bearing cap as shown in the illustration.
Temporarily install the fuel pump assembly with the 2 bolts, leaving some allowance for left and right movement.
23801P
2.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
Do not damage the seals of the union nuts of the No. 1 fuel pipe sub-assembly.
Temporarily install the bolt.
Temporarily install the No. 1 fuel pipe sub-assembly to the fuel delivery pipe and tighten the union nut by hand.
Temporarily install the No. 1 fuel pipe sub-assembly to the fuel pump assembly and tighten the union nut by hand.
23100X
3.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY
Tighten the 2 bolts.
Connect the fuel pump assembly connector.
23801P
4.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
for EGR Valve Bracket Connection Type:
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
|
Union Nut |
|
Bolt |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using an 8 mm socket wrench, tighten the bolt.
for Cylinder Head Cover Sub-assembly Connection Type:
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
|
Union Nut |
|
Bolt |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using an 8 mm socket wrench, tighten the bolt.
Connect the ignition coil connector.
16278
5.INSTALL NO. 2 WATER BY-PASS PIPE
Temporarily install the No. 2 water by-pass pipe to the cylinder block sub-assembly with the bolt (B).
Using an 8 mm socket wrench, temporarily install the No. 2 water by-pass pipe to the intake manifold with the 2 bolts (A).
Tighten the bolt (B).
Using an 8 mm socket wrench, tighten the 2 bolts (A).
| *a | 45° |
| *b | Left Side of Vehicle |
Connect the No. 8 water by-pass hose to the No. 2 water by-pass pipe and slide the clip to secure it.
Engage the clip within the area shown in the illustration.
Engage the clamp to connect the HV air conditioning wire.
23910A
6.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pump assembly and fuel delivery pipe sub-assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the fuel pipe clamp to the fuel tube connector.
25715
7.INSTALL EMISSION CONTROL VALVE BRACKET (w/ Differential Pressure Sensor)
22030
8.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
58441L
10.INSTALL BATTERY SERVICE HOLE COVER
11.INSPECT FOR FUEL LEAK
12.PERFORM INITIALIZATION
Perform "Inspection After Repair" after replacing the fuel pump assembly.
Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION