Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  B1535  NTSC Disconnected (from Park Assist/Monitoring ECU)  C1622  Back Camera Disconnected  


DESCRIPTION

These DTCs are stored if the radio receiver assembly judges that the signals or signal lines between the rear television camera assembly and the multi-display assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1535 NTSC Disconnected (from Park Assist/Monitoring ECU) Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Multi-display assembly

·

Radio receiver assembly


C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Multi-display assembly

·

Radio receiver assembly



WIRING DIAGRAM

E400689E32
3.448,1.354 3.875,1.573 0.427,0.219 10 false CA+ 0.396,1.958 2.115,2.24 1.719,0.281 10 false Radio Receiver Assembly 2.448,2.771 2.875,2.99 0.427,0.219 10 false H7 2.448,2.948 4.021,3.208 1.573,0.26 10 false Multi-display Assembly 5.281,2.271 5.708,2.49 0.427,0.219 10 false W15 5.281,2.448 6.75,2.854 1.469,0.406 10 false Rear Television Camera Assembly 0.729,3.427 2.479,3.729 1.75,0.302 10 false : GVIF Cable 5.313,3.292 6.323,3.531 1.01,0.24 10 false *: Shielded 4.563,1.958 4.99,2.177 0.427,0.219 10 false * 3.531,0.552 3.958,0.771 0.427,0.219 10 false V+ 3.333,1.771 3.958,1.99 0.625,0.219 10 false CGND 3.833,1.24 4.26,1.458 0.427,0.219 10 false 10 3.844,0.448 4.271,0.667 0.427,0.219 10 false 8 3.844,0.844 4.271,1.063 0.427,0.219 10 false 9 3.833,1.656 4.26,1.875 0.427,0.219 10 false 21 3.833,2.052 4.26,2.271 0.427,0.219 10 false 20 3.833,2.302 4.26,2.521 0.427,0.219 10 false 13 5.219,1.229 5.646,1.448 0.427,0.219 10 false 6 5.219,0.448 5.646,0.667 0.427,0.219 10 false 3 5.219,0.854 5.646,1.073 0.427,0.219 10 false 2 5.219,1.656 5.646,1.875 0.427,0.219 10 false 5 5.417,1.365 5.844,1.583 0.427,0.219 10 false CB+ 5.406,0.552 5.833,0.771 0.427,0.219 10 false CV+ 5.417,0.948 5.844,1.167 0.427,0.219 10 false CV- 3.552,0.948 3.979,1.167 0.427,0.219 10 false V- 3.365,2.146 3.99,2.365 0.625,0.219 10 false CSLD 3.344,2.417 3.969,2.635 0.625,0.219 10 false GND1 5.406,1.76 6.031,1.979 0.625,0.219 10 false CGND

CAUTION / NOTICE / HINT

NOTICE:
·

If the cable was disconnected from and reconnected to the negative (-) auxiliary battery terminal, the estimated course lines may not be displayed on the image of the area behind the vehicle. In this case, perform "Correct the Steering Angle Neutral Point".

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION

·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>PRECAUTION



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Change the shift position to R and check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H7 multi-display assembly connector.


b.

Disconnect the W15 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-8 (V+) - W15-3 (CV+) Always Below 1 Ω
H7-9 (V-) - W15-2 (CV-) Always Below 1 Ω
H7-10 (CA+) - W15-6 (CB+) Always Below 1 Ω
H7-21 (CGND) - W15-5 (CGND) Always Below 1 Ω
H7-8 (V+) or W15-3 (CV+) - Body ground Always 10 kΩ or higher
H7-9 (V-) or W15-2 (CV-) - Body ground Always 10 kΩ or higher
H7-10 (CA+) or W15-6 (CB+) - Body ground Always 10 kΩ or higher
H7-21 (CGND) or W15-5 (CGND) - Body ground Always 10 kΩ or higher
H7-20 (CSLD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MULTI-DISPLAY ASSEMBLY
a.

Reconnect the H7 multi-display assembly connector.


b.
E362596C24
1.458,0.115 1.875,0.365 0.417,0.25 0.896,0.313 1.052,0.313 1.052,0.313 1.344,0.792 true 0.885,1.729 1.042,1.729 1.042,1.729 1.458,0.979 true 1.594,0.156 1.927,0.365 0.333,0.208 10 false H7 0.135,0.104 0.469,0.313 0.333,0.208 10 false *a 0.563,0.219 0.885,0.427 0.323,0.208 10 false CA+ 0.438,1.656 0.927,1.844 0.49,0.188 10 false CGND
*a Component with harness connected
(Multi-display Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-21 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H7-10 (CA+) - H7-21 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.INSPECT MULTI-DISPLAY ASSEMBLY

NG

4.INSPECT MULTI-DISPLAY ASSEMBLY
a.

Reconnect the W15 rear television camera assembly connector.


b.
E400750C60
1.5,0.25 1.917,0.5 0.417,0.25 1.542,1.146 1.031,0.594 false 2.448,1.75 2.302,1.302 false 0.156,0.125 0.469,0.281 0.313,0.156 10 false *a 0.854,0.406 1.167,0.563 0.313,0.156 10 false V+ 2.313,1.781 2.823,1.979 0.51,0.198 10 false GND1 1.635,0.281 2.063,0.469 0.427,0.188 10 false H7
*a Component with harness connected
(Multi-display Assembly)


E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-display assembly with the connector connected.


Item Condition
Measurement terminal H7-8 (V+) - H7-13 (GND1)
Tool setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

OK:

The waveform is similar to that shown in the illustration.


HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the ignition switch is turned to ACC.




Result:
Proceed to
OK
NG



OK

5.REPLACE MULTI-DISPLAY ASSEMBLY

NG

5.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

Change the shift position to R and check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO RECEIVER ASSEMBLY