Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.11
RM37A0E _51 Engine / Hybrid System _086851 2GR-FKS ENGINE MECHANICAL _0420087 ENGINE UNIT A

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16522 1.INSTALL WATER FILLER BRACKET

a.
A408398C01
1.323,0.969 0.885,0.729 true 1.333,1.031 0.813,1.51 true 0.573,1.438 0.792,1.635 0.219,0.198 10 true *a 0.604,0.615 0.844,0.781 0.24,0.167 10 true *b 1.688,1.458 1.854,1.656 0.167,0.198 10 true 2 2.125,0.625 2.271,0.792 0.146,0.167 10 true 1
*a Stopper
*b Protrusion


Temporarily install the water filler bracket to the camshaft housing sub-assembly LH with the 2 bolts.


b.

Fully tighten the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Make sure that the stopper of the water filler bracket is pressed against the protrusion of the camshaft housing sub-assembly LH when fully tightening the 2 bolts.



Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Install the wire harness clamp bracket to the camshaft housing sub-assembly LH with the bolt.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 43457 3.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket to the cylinder block sub-assembly with the 3 bolts.

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)

NOTICE:

Make sure that there is no oil on the threads of the bolts.



Hide 12585 4.INSTALL NO. 5 CYLINDER BLOCK INSULATOR

a.
A374183C01
2.375,3.031 0.729,2.688 0.729,2.688 2.573,2.125 true 2.063,2.75 0.802,2.688 0.802,2.688 2.573,2.323 true 0.542,2.604 0.854,2.76 0.313,0.156 10 false *a
*a Fastener Surface


Install the No. 5 cylinder block insulator to the engine assembly.

NOTICE:

Make sure that the No. 5 cylinder block insulator is not covering any fastener surface.



Hide 11452 5.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Install a new engine oil level dipstick guide O-ring to the engine oil level dipstick guide.


b.

Apply a light coat of engine oil to the engine oil level dipstick guide O-ring.


c.

Insert the engine oil level dipstick guide end into the oil pan sub-assembly.


d.

Install the engine oil level dipstick guide to the camshaft housing sub-assembly LH with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Install the engine oil level dipstick to the engine oil level dipstick guide.


Hide 16173 6.INSTALL WATER PUMP PULLEY

Hide 16620 7.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16604 8.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 88431 9.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

a.
A408030N01
1.344,0.219 1.5,0.417 0.156,0.198 10 true 1 2.26,0.823 2.417,1.021 0.156,0.198 10 true 2

Temporarily install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 2 bolts.


b.

Fully tighten the 2 bolts in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 10.INSTALL COMPRESSOR AND MAGNETIC CLUTCH

Hide 27020 11.INSTALL GENERATOR ASSEMBLY

a.
A455109C01
1.802,3.208 2.115,3.365 0.313,0.156 10 false *a 1.802,3.792 2.115,3.948 0.313,0.156 10 false *b 2.354,3.49 2.667,3.646 0.313,0.156 10 false *c
*a 14 mm (0.551 in.)
*b 13 mm (0.512 in.)
*c 29 mm (1.14 in.)


w/ Stud Bolt

i.

Using an E8 "TORX" socket wrench, install the stud bolt to the cylinder block sub-assembly.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)




Hide 16361A 12.INSTALL V-RIBBED BELT

Hide 12262 13.INSTALL NO. 2 VENTILATION HOSE

a.

Install the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 12261 14.INSTALL VENTILATION HOSE

a.

Install the ventilation hose to the PCV valve (ventilation valve sub-assembly) and slide the clip to secure it.


Hide 16264 15.INSTALL NO. 2 WATER BY-PASS HOSE

a.

Install the No. 2 water by-pass hose to the water outlet and slide the clip to secure it.


Hide 16267 16.INSTALL NO. 3 WATER BY-PASS HOSE

a.

Install the No. 3 water by-pass hose to the water inlet pipe and slide the clip to secure it.


Hide 16260 17.INSTALL WATER BY-PASS HOSE ASSEMBLY

a.

Install the water by-pass hose assembly to the water inlet pipe and slide the clip to secure it.


Hide 29300 18.INSTALL VACUUM PUMP ASSEMBLY

Hide 82219A 20.INSTALL SENSOR WIRE

a.

Engage the 2 clamps and install the sensor wire with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 89615 21.INSTALL KNOCK CONTROL SENSOR