This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and radio and display receiver assembly or multi-display assembly are not normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1621 | Back Camera Power Supply Failure | Rear television camera assembly power supply failure | ·
Harness or connector ·
Rear television camera assembly ·
Radio and display receiver assembly*1 ·
Multi-display assembly*2 |
*1: for 8 Inch Display
*2: for 12.3 Inch Display
When the "!" mark is displayed on the radio and display receiver assembly or multi-display assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>CALIBRATION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 8 Inch Display | A |
| for 12.3 Inch Display | B |
A
B
Disconnect the H2 radio and display receiver assembly connector.
Disconnect the W15 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H2-30 (CA+) - W15-6 (CB+) | Always | Below 1 Ω |
| H2-27 (CGND) - W15-5 (CGND) | Always | Below 1 Ω |
| H2-30 (CA+) or W15-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| H2-27 (CGND) or W15-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the W15 rear television camera assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H2-27 (CGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H2-30 (CA+) - H2-27 (CGND) | Ignition switch ACC | 5.5 to 7.05 V |
| H2-30 (CA+) - H2-27 (CGND) | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H7 multi-display assembly connector.
Disconnect the W15 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H7-10 (CA+) - W15-6 (CB+) | Always | Below 1 Ω |
| H7-21 (CGND) - W15-5 (CGND) | Always | Below 1 Ω |
| H7-10 (CA+) or W15-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| H7-21 (CGND) or W15-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H7 multi-display assembly connector.
| *a | Component with harness connected
(Multi-display Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H7-10 (CA+) - H7-21 (CGND) | Ignition switch ACC | 5.8 to 6.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG