Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM (for 4WD/AWD) › 2020.11–2021.10
RM37A0E _51 Engine / Hybrid System _086850 HYBRID / BATTERY CONTROL _0420994 HYBRID CONTROL SYSTEM(for 4WD/AWD) J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM(for 4WD/AWD)  Cooling System  


DESCRIPTION

The cause of the malfunction may be the cooling system.

Check whether the grille is blocked, whether coolant is leaking, the radiator fan operating condition and whether coolant has frozen.

Related Parts Check
Area Inspection
Grille blockage, coolant amount, coolant hoses, radiator fan Check for overheating due to hybrid cooling system malfunction.
Inverter coolant temperature sensor (built-in inverter) Check for temperature sensor malfunction.
Coolant freezing check Check freeze frame values to determine whether the hybrid coolant was frozen when the DTC was stored.

Related Data List
Data List
·

Inverter Coolant Water Temperature

·

Motor Inverter Temperature

·

Rear Motor Inverter Temperature

·

Generator Inverter Calculated Temperature

·

Boosting Converter Temperature (Upper)

·

Boosting Converter Temperature (Lower)

·

Ambient Temperature

·

Inverter Water Pump Revolution



SYSTEM DESCRIPTION

The inverter converts the high-voltage direct current of the HV battery into alternating current for the generator (MG1), motor (MG2) and rear motor (MGR). The inverter generates heat during the conversion process. Therefore, the inverter is cooled by a special cooling system consisting of the inverter water pump assembly, the cooling fan, and a radiator. This cooling system is independent of the engine cooling system. The hybrid vehicle control ECU monitors the inverter water pump assembly, cooling fan and cooling system, and detects malfunctions.

A449766C01
5.833,1.385 5.99,0.26 5.99,0.26 6.156,0.26 true 4.156,0.76 3.823,0.219 3.823,0.219 3.656,0.219 true 6.031,3.188 6.24,4.146 6.24,4.146 6.406,4.146 true 4.083,3.042 4.219,4.115 4.219,4.115 4.385,4.115 true 0.958,4.094 2.438,4.385 2.438,4.385 2.583,4.385 true 2.635,4.313 2.948,4.469 0.313,0.156 10 false *1 3.5,0.146 3.813,0.302 0.313,0.156 10 false *2 6.208,0.188 6.521,0.344 0.313,0.156 10 false *3 4.438,4.042 4.75,4.198 0.313,0.156 10 false *4 6.448,4.073 6.76,4.229 0.313,0.156 10 false *5
*1 Inverter Water Pump Assembly *2 Inverter Reserve Tank Assembly
*3 Inverter with Converter Assembly *4 Radiator Assembly (HV)
*5 Hybrid Vehicle Transaxle Assembly - -


WIRING DIAGRAM

A449799E01
5.427,5.604 7.135,5.865 1.708,0.26 10 false Hybrid Vehicle Control ECU 5.865,5.115 6.177,5.313 0.313,0.198 10 false E1 5.875,4.5 6.438,4.74 0.563,0.24 10 false MREL 5.865,3.01 6.427,3.25 0.563,0.24 10 false NIWP 5.865,1.5 6.427,1.74 0.563,0.24 10 false IWP 6.615,2.625 6.938,2.896 0.323,0.271 10 false +B 6.75,3.927 7.073,4.198 0.323,0.271 10 false +B 5.521,5.094 5.833,5.292 0.313,0.198 10 false H67 5.594,4.885 5.906,5.083 0.313,0.198 10 false 3 3.094,4.063 3.406,4.26 0.313,0.198 10 false A56 5.594,4.385 5.906,4.583 0.313,0.198 10 false 5 5.51,3.104 5.823,3.302 0.313,0.198 10 false A31 5.51,1.604 5.823,1.802 0.313,0.198 10 false A31 5.563,2.906 5.875,3.104 0.313,0.198 10 false 33 5.563,1.396 5.875,1.594 0.313,0.198 10 false 34 5.146,3.625 5.458,3.823 0.313,0.198 10 false 1 4.76,3.75 5.208,4 0.448,0.25 10 false GND 4.729,3.01 5.292,3.25 0.563,0.24 10 false NWP 5.156,3 5.469,3.198 0.313,0.198 10 false 2 4.74,1.5 5.302,1.74 0.563,0.24 10 false SWP 5.156,1.49 5.469,1.688 0.313,0.198 10 false 3 3.344,2.135 4.271,2.479 0.927,0.344 10 false Drive Circuit 2.844,1.177 3.406,1.417 0.563,0.24 10 false +BWP 2.656,1.188 2.969,1.385 0.313,0.198 10 false 4 1.438,4.938 1.969,5.271 0.531,0.333 10 false IGCT 2.063,4.365 3.031,4.583 0.969,0.219 10 false IGCT NO. 2 1.917,1.573 2.229,1.771 0.313,0.198 10 false 1 1.917,1.188 2.229,1.385 0.313,0.198 10 false 3 0.25,2.865 0.656,3.052 0.406,0.188 10 false MAIN 0.073,5.688 1.479,5.948 1.406,0.26 10 false from Auxiliary Battery 0.354,6.094 3.219,6.292 2.865,0.198 10 false IWP: Inverter water pump assembly drive duty 0.333,6.438 3.396,6.635 3.063,0.198 10 false NIWP: Inverter water pump assembly speed signal 3.083,4.229 5.031,4.469 1.948,0.24 10 false Inverter Water Pump Assembly 5.51,4.604 5.823,4.802 0.313,0.198 10 false A31 0.333,1.427 1.115,1.771 0.781,0.344 10 false INV W/PMP 1.167,1.177 1.479,1.375 0.313,0.198 10 false 5 1.167,1.563 1.479,1.76 0.313,0.198 10 false 2 0.469,4.375 1.135,4.594 0.667,0.219 10 false IGCT-IG 1.896,4.125 2.208,4.323 0.313,0.198 10 false 5 1.167,4.125 1.479,4.323 0.313,0.198 10 false 3 1.167,4.49 1.479,4.688 0.313,0.198 10 false 2 1.896,4.49 2.208,4.688 0.313,0.198 10 false 1 0.823,1.146 1.135,1.344 0.313,0.198 10 false 2 0.5,1.146 0.813,1.344 0.313,0.198 10 false 1 0.521,4.094 0.833,4.292 0.313,0.198 10 false 1 2.167,4.104 2.479,4.302 0.313,0.198 10 false 1 0.854,4.094 1.167,4.292 0.313,0.198 10 false 2 2.552,4.094 2.865,4.292 0.313,0.198 10 false 2 1.229,2.01 2.01,2.354 0.781,0.344 10 false INV W/PMP

CAUTION / NOTICE / HINT

This diagnostic procedure is referenced to in the diagnostic procedure of several DTCs.

If the result of this diagnostic procedure is normal, proceed as directed in the procedure for the DTC.

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Make sure that the front side of the radiator grille is not blocked with anything.


b.

Ask the customer if the front side of the radiator grille was blocked with anything.


Result:
Result Proceed to
Not blocked. A
Is/was blocked. B


HINT:

If the radiator grille is blocked, the inverter coolant temperature will increase and this DTC may be stored.



A

2.CHECK QUANTITY OF HV COOLANT

B

IF EQUIPPED, EXPLAIN TO CUSTOMER THAT OPTIONAL COMPONENTS WILL BE REMOVED

2.CHECK QUANTITY OF HV COOLANT
a.

Check the HV coolant level in the inverter reserve tank.


b.

Check for HV coolant leaks.

Result:
Result Proceed to
No leaks are found and the HV coolant level in the inverter reserve tank assembly is above the low line. A
No leaks are found and the HV coolant level in the inverter reserve tank assembly is below the low line. B
HV coolant leaks are evident. C


HINT:
·

After repairing the HV coolant leaks and adding coolant, perform the Active Tests "Activate the Inverter Water Pump" (Hybrid Control System) and "Control the Cooling Fan Duty Ratio" (Engine Control System) and make sure that there are no malfunctions.

·

If there are signs of coolant leakage around the connecting parts of a hose and the inverter with converter assembly, replace the hose with a new one.





A

3.CHECK COOLANT HOSE

B

ADD HV COOLANT

C

INSPECT FOR COOLANT LEAK AND ADD COOLANT

3.CHECK COOLANT HOSE
a.

Check that the cooling system hoses are not kinked or clogged.

OK:

The cooling system hoses are not kinked or clogged.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)

NG

REPAIR OR REPLACE COOLANT HOSE

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE ENGINE COOLING FAN DUTY RATIO)
a.

Perform the "Control the Engine Cooling Fan Duty Ratio" Active Test.

Powertrain > Engine > Active Test
Tester Display
Control the Engine Cooling Fan Duty Ratio
50004 372 11
OK:
GTS Operation Fan Operation
30 - 100% Cooling fan operates
0% Cooling fan stops



Result:
Result Proceed to
Cooling fan operate (w/ Grille Shutter System) A
Cooling fan operate (w/o Grille Shutter System) B
Cooling fan does not operate C
Cooling fan do not stop


b.

Turn the ignition switch off.



A

5.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)

B

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)

C

5.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

b.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Closing Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 3 8
OK:

"Normal" is displayed.



c.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Opening Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 4 8
OK:

"Normal" is displayed.



HINT:

When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the Grille Shutter System is normal.


d.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)

NG

6.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE INVERTER WATER PUMP)
NOTICE:
·

Make sure that the HV coolant level is above the low line of the inverter reserve tank.

·

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.



HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.

According to the display on the GTS, perform the Active Test "Activate the Inverter Water Pump" and check the value of the Data List item "Inverter Water Pump Revolution".

Powertrain > Hybrid Control > Active Test
Active Test Display
Activate the Inverter Water Pump
Data List Display
Inverter Water Pump Revolution
50004 397 1 60
OK:
Tester Display Condition Specified Condition
Inverter Water Pump Revolution Ignition switch ON
During Active Test
3176 to 8617 rpm


HINT:
·

Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).

·

When the inverter water pump assembly is not operating, the Data List item "Inverter Water Pump Revolution" displays a value 200 rpm or less.




b.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (DATA LIST)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
7.READ VALUE USING GTS (DATA LIST)
a.

Turn the ignition switch to ON (READY) and wait for 1 minute with the engine stopped.


b.

Read the Data List with the engine stopped.

Powertrain > Hybrid Control > Data List
Tester Display
Generator Inverter Calculated Temperature
Motor Inverter Temperature
Rear Motor Inverter Temperature
Boosting Converter Temperature (Upper)
Boosting Converter Temperature (Lower)
Inverter Coolant Water Temperature
50003 397 127,130,133,136,137,152
Result:
Result Proceed to
Other than below. A
"Inverter Coolant Water Temperature" value is higher than the displayed temperature of any other Data List item by 20°C (68°F) or more. B


HINT:

The lower limit temperature that can be displayed for "Generator Inverter Calculated Temperature", "Motor Inverter Temperature", "Boosting Converter Temperature (Upper)" and "Boosting Converter Temperature (Lower)" is 0°C (32°F). The lower limit temperature for "Inverter Coolant Water Temperature" is -40°C (-40°F). The "Inverter Coolant Water Temperature" value displayed on the GTS may be lower than the others, but this is not a malfunction.



c.

Turn the ignition switch off.



A

8.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)

B

REPLACE INVERTER WITH CONVERTER ASSEMBLY

8.CHECK HV COOLANT (CHECK FOR CONDITIONS THAT MAY HAVE CAUSED FREEZING)
a.

Read the Freeze Frame Data item "Ambient Temperature" using the GTS.

Powertrain > Hybrid Control > Trouble Codes
50001 397

b.

Check if the Freeze Frame Data item "Ambient Temperature" is below the freezing temperature of the HV coolant.

Result:
Result Proceed to
Ambient Temperature value is above freezing temperature of the HV coolant. A
Ambient Temperature value is below freezing temperature of the HV coolant. B


HINT:
·

HV coolant (SLLC) with a 30% concentration freezes at -15°C (5°F) and HV coolant (SLLC) with a 50% concentration freezes at -35°C (-31°F).

·

If the HV coolant freezes in the HV radiator or inverter water pump, the coolant temperature in the inverter with converter assembly rises because the HV coolant cannot circulate. As a result, a DTC may be stored.

·

A DTC is stored when the inverter water pump impeller cannot rotate due to freezing of the HV coolant.

·

If DTCs are output due to freezing of the LLC, the problem symptom cannot be reproduced. Check the LLC replacement history and whether the LLC was frozen based on the ambient temperature when the DTCs were stored.




c.

Turn the ignition switch off.



A

COOLING SYSTEM NORMAL (PERFORM NEXT STEP FOR REFERENCED DTC)

B

9.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

OK

10.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

10.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WATER PUMP ASSEMBLY CONNECTOR)
a.
A449767N01
1.865,1.469 2.229,1.698 0.365,0.229 1.906,1.49 2.208,1.677 0.302,0.188 10 true A56

Check the connector connections and contact pressure of the relevant terminals for the A56 inverter water pump assembly connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

OK:

The connector is connected securely, the terminals are not deformed or corroded and there are no contact problems.



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

CONNECT SECURELY

11.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.

Disconnect the A56 inverter water pump assembly connector.


c.
A368425C21
1.542,2.688 1.896,2.958 0.354,0.271 1.427,0.333 1.823,0.594 0.396,0.26 2.385,2.323 2.542,1.719 true 1.708,4.094 1.823,3.552 true 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.188,2.729 0.5,2.927 0.313,0.198 10 false *b 1.552,4.135 2.104,4.427 0.552,0.292 10 false SWP 2.26,2.365 2.635,2.563 0.375,0.198 10 false IWP 1.51,0.375 2.063,0.667 0.552,0.292 10 false A31 1.604,2.75 2.156,3.042 0.552,0.292 10 false A56
*a Front view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Inverter Water Pump Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A31-34 (IWP) - A56-3 (SWP) Ignition switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A31-34 (IWP) or A56-3 (SWP) - Body ground and other terminals Ignition switch off 10 kΩ or higher


HINT:

Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.



d.

Reconnect the A56 inverter water pump assembly connector.


e.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

12.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.READ VALUE USING GTS (INVERTER WATER PUMP REVOLUTION)
NOTICE:

Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.


HINT:

When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.


a.
A449764C01
2,1.698 2.604,2.458 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *1 2.635,2.458 2.948,2.656 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Fuse


Remove the INV W/PMP fuse from No. 1 engine room relay block and No. 1 junction block assembly.


b.

According to the display on the GTS, read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display
Inverter Water Pump Revolution
50003 397 60
OK:
Tester Display Condition Specified Condition
Inverter Water Pump Revolution Ignition switch ON 200 rpm or less



c.

Turn the ignition switch off.


d.

Install the INV W/PMP fuse.


Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INVERTER WATER PUMP ASSEMBLY)
a.

Disconnect the A31 hybrid vehicle control ECU connector.


b.
A449788C01
0.146,0.115 0.458,0.313 0.313,0.198 10 false *1 0.333,1.24 0.646,1.438 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block and No. 1 Junction Block Assembly
*2 INV W/PMP Relay Holder


Remove the INV W/PMP relay from No. 1 engine room relay block and No. 1 junction block assembly.


c.

Connect terminals 3 and 5 of the INV W/PMP relay holder.

HINT:

Make a short circuit between terminals 3 and 5 to supply +B voltage to the inverter water pump.



d.

Measure the voltage according to the value(s) in the table below.

A368426C30
5.26,0.167 5.656,0.458 0.396,0.292 2.76,2.698 3.156,2.948 0.396,0.25 2.479,3.448 2.313,3.042 true 5.906,2.104 5.99,1.177 true 0.375,2.135 0.688,2.333 0.313,0.198 10 false *b 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 5.323,0.229 5.698,0.427 0.375,0.198 10 false H67 2.823,2.74 3.135,2.938 0.313,0.198 10 false A31 2.406,3.469 2.865,3.667 0.458,0.198 10 false IWP 5.823,2.125 6.281,2.323 0.458,0.198 10 false E1
*a Component with harness connected
(Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Hybrid Vehicle Control ECU)


Standard Voltage:
Tester Connection Condition Specified Condition
A31-34 (IWP) - H67-3 (E1) INV W/PMP relay holder terminals 3 and 5 connected
Ignition switch off
11 to 14 V


NOTICE:

Make sure to check for and clear DTCs after performing this inspection.



e.

Install the INV W/PMP relay.


f.

Reconnect the A31 hybrid vehicle control ECU connector.


Result:
Proceed to
OK
NG



OK

14.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

NG

15.REPLACE INVERTER WATER PUMP ASSEMBLY
14.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.


b.

Turn the ignition switch to ON.


c.

Check the waveform while turning the ignition switch to ON.

C407546C90
5.271,0.344 5.615,0.594 0.344,0.25 1.552,0.344 1.896,0.594 0.344,0.25 1.125,1.49 1.375,2.271 true 6.01,1.302 5.917,2.302 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 5.333,0.396 5.792,0.594 0.458,0.198 10 false H67 1.292,2.313 1.781,2.563 0.49,0.25 10 false IWP 5.833,2.354 6.104,2.531 0.271,0.177 10 false E1 1.615,0.396 2.073,0.594 0.458,0.198 10 false A31
*a Component with harness connected
(Hybrid Vehicle Control ECU)
- -


Item Content
Terminal A31-34 (IWP) - H67-3 (E1)
Equipment Setting 5 V/DIV., 50 ms./DIV.
Condition Ignition switch ON

OK:

Waveform duty ratio is between 3% and 9%.



d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

15.REPLACE INVERTER WATER PUMP ASSEMBLY

NG

15.REPLACE INVERTER WATER PUMP ASSEMBLY

NEXT

16.ADD HV COOLANT AND PERFORM AIR BLEEDING
16.ADD HV COOLANT AND PERFORM AIR BLEEDING
a.

After replacing the inverter water pump assembly, add HV coolant and perform air bleeding.

Click hereGeneral>MAINTENANCE>COOLANT (for Inverter)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

END