Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure (X21D2)  


DESCRIPTION

Code Tester Display Measurement Item Trouble Area Output ECU
X21D2 Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure History of mismatch between brake pedal stroke sensor assembly and reaction force pressure sensor
·

Brake booster with master cylinder assembly

·

Brake pedal stroke sensor assembly


No. 1 skid control ECU (brake booster with master cylinder assembly)

PROCEDURE

1.CHECK DTC (HEALTH CHECK)
a.

Perform the Health Check using the GTS.


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.CUSTOMER PROBLEM ANALYSIS (CHECK CONDITION WHEN MALFUNCTION OCCURRED) AND FREEZE FRAME DATA
a.

Interview the customer to check the vehicle conditions when the brake system warning light (red indicator) and brake system warning light (yellow indicator) illuminated.


b.

Using the GTS, check for Freeze Frame Data that is recorded when a X21D2 is stored.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>VEHICLE CONTROL HISTORY

Chassis > Brake Booster > Utility
Tester Display
Vehicle Control History (RoB)
50005 466 1055
HINT:
·

Freeze Frame Data is only stored once when a X21D2 is stored.

·

If other vehicle control history are output, repair any malfunctions related to those vehicle control history first, and then reproduce the conditions that caused X21D2 to be stored based on the interview with the customer.




Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)
3.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

With the brake pedal released, confirm the brake pedal stroke sensor assembly output voltage.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 0.6 to 1.4 V Reading increases when brake pedal is depressed
Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
OK:

0.6 to 1.4 V



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)

NG

4.READ VALUE USING GTS (BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Mount a pedal effort gauge.


c.

Turn the ignition switch to ON (READY) and depress the brake pedal once.

HINT:

Depress the brake pedal after turning the ignition switch to ON (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).



d.

Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stroke Sensor Brake pedal stroke sensor 1 Min.: 0.0 V
Max.: 5.0 V
Brake pedal released: 0.6 to 1.4 V Reading increases when brake pedal is depressed
Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207
HINT:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Voltage:
for Europe (LHD)
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
50 (5, 11.2) 1.20 to 1.90
100 (10, 22.5) 1.42 to 2.12
150 (15, 33.7) 1.61 to 2.31

for Europe (RHD)
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
50 (5, 11.2) 1.17 to 1.87
100 (10, 22.5) 1.37 to 2.07
150 (15, 33.7) 1.55 to 2.25

for Middle East
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
50 (5, 11.2) 1.20 to 1.90
100 (10, 22.5) 1.42 to 2.16
150 (15, 33.7) 1.61 to 2.31

for Australia
Brake Effort
[N (kgf, lbf)]
Stroke Sensor
[V]
50 (5, 11.2) 1.17 to 1.87
100 (10, 22.5) 1.37 to 2.07
150 (15, 33.7) 1.55 to 2.25



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (REACTION FORCE PRESSURE)

NG

5.READ VALUE USING GTS (REACTION FORCE PRESSURE)
a.

Depress the brake pedal slowly and check the reaction force pressure sensor output values with respect to brake pedal depression force.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Reaction Force Pressure Pressure value of stroke simulator Min.: 0.00 MPa
Max.: 24.48 MPa
Brake pedal released: 0.00 to 1.53 MPa Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal
Chassis > Brake Booster > Data List
Tester Display
Reaction Force Pressure
50003 466 205
HINT:

Perform this procedure in linear mode (switching solenoid (SSA) on).


Standard Pressure:
Brake Effort
[N (kgf, lbf)]
Reaction Force Pressure
[MPa]
50 (5, 11.2) 0.00 to 0.68
100 (10, 22.5) 0.61 to 1.41
150 (15, 33.7) 1.29 to 2.09
200 (20, 45.0) 1.96 to 2.76



Result:
Proceed to
OK
NG



OK

6.CLEAR VEHICLE CONTROL HISTORY

NG

CHECK AND REPAIR BRAKE FLUID LEAKS

6.CLEAR VEHICLE CONTROL HISTORY
a.

Using the GTS, clear the Vehicle Control History.

Chassis > Brake Booster > Utility
Tester Display
Vehicle Control History (RoB)
50005 466 55

Result:
Proceed to
NEXT



NEXT

7.CHECK VEHICLE CONTROL HISTORY
7.CHECK VEHICLE CONTROL HISTORY
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Using the GTS, check for Vehicle Control History.

Chassis > Brake Booster > Utility
Tester Display
Vehicle Control History (RoB)
50005 466 55

Result:
Result Proceed to
X21D2 is not output. A
X21D2 is output. B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY