Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  C05C051  Brake Pedal Position Sensor "A" Not Programmed  


DESCRIPTION

When the No. 1 skid control ECU (brake booster with master cylinder assembly) judges that the zero point calibration of the brake pedal stroke sensor assembly is incomplete, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C05C051 Brake Pedal Position Sensor "A" Not Programmed The brake pedal stroke sensor assembly zero point calibration is not performed.
(Normal brake pedal stroke sensor assembly zero point not memorized.)
·

Valid brake pedal stroke sensor assembly zero point not memorized.

(Calibration not performed or not completed)

·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
HINT:

During Dealer Mode, related DTCs are cleared.



CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.




Result:
Proceed to
NEXT



NEXT

2.PERFORM BRAKE PEDAL STROKE SENSOR ASSEMBLY ZERO POINT CALIBRATION
2.PERFORM BRAKE PEDAL STROKE SENSOR ASSEMBLY ZERO POINT CALIBRATION
a.

Perform brake pedal stroke sensor assembly zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY

Chassis > Brake/EPB > Utility
Tester Display
Reset Memory
50005 435 4560
Chassis > Brake/EPB > Utility
Tester Display
Calibration
50005 435 4554

Result:
Proceed to
NEXT



NEXT

3.CLEAR DTC
3.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake Booster > Trouble Codes
50001 466
Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Only DTC C05C051 is output. A
DTCs are not output. B
DTCs other than C05C051 are output. C



A

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)

B

END

C

5.INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)
a.
C156491C88
0.333,1.167 0.75,1.417 0.417,0.25 1.75,2.313 1.458,2.906 true 2.24,2.938 1.969,2.313 true 0.219,0.24 0.531,0.438 0.313,0.198 10 false *a 0.427,1.208 0.74,1.406 0.313,0.198 10 false A43 2.115,2.979 2.552,3.208 0.438,0.229 10 false SKG 1.26,2.969 1.698,3.208 0.438,0.24 10 false VCSK
*a Front view of wire harness connector
(to Brake Pedal Stroke Sensor Assembly)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A43 brake pedal stroke sensor assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A43-4 (VCSK) - A43-5 (SKG) Ignition switch ON 4.84 to 5.16 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR