The No. 2 skid control ECU (brake actuator assembly) controls the brake fluid pressure of each wheel cylinder based on the brake fluid pressure sensor.
DTCs may be stored if one of the following occurs:
Brake fluid leaks.
Foreign matter enters a solenoid valve.
Brake pads are replaced.
Rotors are replaced.
When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| C140000 | Brake Pressure Leak Malfunction | When all of the following conditions are met, a malfunction such as a leak in an ABS decrease pressure valve of the brake actuator assembly is detected:
·
The vehicle was driven before the ignition switch was turned off. ·
90 seconds have elapsed since the ignition switch was turned off. ·
The vehicle is stopped and the shift position is P. |
·
Brake booster with master cylinder assembly ·
Brake actuator assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| C140A00 | Pressure Control Reservoir Leak Malfunction | When all of the following conditions are met, a malfunction is detected by the No. 2 skid control ECU (brake actuator assembly) during self-diagnosis.
·
The vehicle was driven before the ignition switch was turned off. ·
90 seconds have elapsed since the ignition switch was turned off. ·
The vehicle is stopped and the shift position is P. |
·
Brake booster with master cylinder assembly ·
Brake actuator assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
After replacing the No. 2 skid control ECU (brake actuator assembly), perform "Calibration".
Mount a pedal effort gauge.
Disconnect the A9 brake booster with accumulator pump assembly connector.
Depress the brake pedal 10 times or more until it becomes hard.
Depressing the brake pedal with the connector of the brake booster with accumulator pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.
Connect an LSPV gauge set.
Slowly depress the brake pedal and check the wheel cylinder pressure with respect to brake pedal depression force.
Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.
| Brake Effort
[N (kgf, lbf)] |
Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
|---|---|
| 200 (20, 45.0) | 0.00 to 2.89 (0.0 to 29.5, 0 to 419) |
| 500 (51, 112.4) | 1.16 to 5.16 (11.8 to 52.6, 168 to 748) |
| Brake Effort
[N (kgf, lbf)] |
Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
|---|---|
| 200 (20, 45.0) | 0.00 to 2.89 (0.0 to 29.5, 0 to 419) |
| 500 (51, 112.4) | 1.16 to 5.16 (11.8 to 52.6, 168 to 748) |
| Brake Effort
[N (kgf, lbf)] |
Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
|---|---|
| 200 (20, 45.0) | 0.00 to 2.88 (0.0 to 29.4, 0 to 418) |
| 500 (51, 112.4) | 1.13 to 5.13 (11.5 to 52.3, 164 to 744) |
| Brake Effort
[N (kgf, lbf)] |
Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
|---|---|
| 200 (20, 45.0) | 0.00 to 2.88 (0.0 to 29.4, 0 to 418) |
| 500 (51, 112.4) | 1.13 to 5.13 (11.5 to 52.3, 164 to 744) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTCs C140000 and C140A00 are not output. | A |
| DTCs C140000 and/or C140A00 are output. | B |
| DTC C140A00 and C139A00 are output at the same time. | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model RHD)>REMOVAL
C
for Brake Booster with Master Cylinder Assembly (for LHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL
for Brake Booster with Master Cylinder Assembly (for RHD): Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model RHD)>REMOVAL
for Brake Actuator Assembly (for LHD): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for Brake Actuator Assembly (for RHD): Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model RHD)>REMOVAL
Brake fluid leaks and air in brake line inspection
Check and take a note of the fluid level in the brake master cylinder reservoir assembly.
Repeatedly depress the brake pedal and confirm that the brake pedal feels normal (no air in the system, etc.).
Check if the brake fluid level in the brake master cylinder reservoir assembly has changed.
If the brake fluid level has decreased, check for leaks due to damaged brake lines or hoses, loose union nuts, damaged brake master cylinder assembly seals, etc.
There are no brake fluid leaks and no air in the system.
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model RHD)>REMOVAL
NG