Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0421002 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model)  P057A12  Brake Pedal Position Sensor "A" Circuit Short to Battery  P057A14  Brake Pedal Position Sensor "A" Circuit Short to Ground or Open  P057A1F  Brake Pedal Position Sensor "A" Circuit Intermittent  


DESCRIPTION

Refer to DTC C110000.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>C110000

DTC No. Detection Item DTC Detection Condition Trouble Area Note
P057A12 Brake Pedal Position Sensor "A" Circuit Short to Battery The sensor output voltage 1 (SKS1) is 4.7 V or more for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
P057A14 Brake Pedal Position Sensor "A" Circuit Short to Ground or Open The sensor output voltage 1 (SKS1) is less than 0.3 V for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)
P057A1F Brake Pedal Position Sensor "A" Circuit Intermittent The difference between the current value and previous value of the sensor output voltage 1 (SKS1) is 8.5% or more for 0.2 seconds or more.
·

Wire harness and connector

·

Brake pedal stroke sensor assembly


Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>UTILITY


PROCEDURE

1.CHECK BRAKE PEDAL
a.

Check that the brake pedal and the brake pedal stroke sensor assembly are properly installed and that the pedal can be depressed normally.




Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE PEDAL STROKE SENSOR ASSEMBLY)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.


d.

Disconnect the A43 brake pedal stroke sensor assembly connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A44-3 (SKS1) - A43-6 (SKS1) Always Below 1 Ω
A44-3 (SKS1) or A43-6 (SKS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR