If the No. 1 skid control ECU (brake booster with master cylinder assembly) detects an inconsistency between the brake pedal stroke sensor assembly signal and reaction force pressure sensor signal, DTC P05FF62 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| P05FF62 | Brake Pressure Sensor / Brake Pedal Position Sensor Signal Compare Failure | The difference between brake pedal stroke sensor assembly output value and reaction force pressure sensor output value is above the threshold for a certain period of time. | ·
Brake booster with master cylinder assembly ·
Brake pedal stroke sensor assembly ·
Brake pedal stroke sensor assembly installation ·
Brake fluid leaks |
Output ECU: No. 1 skid control ECU (brake booster with master cylinder assembly) |
After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".
After replacing the No. 1 skid control ECU (brake booster with master cylinder assembly), perform "Calibration".
If the detection conditions for X21D2 are met 3 times in a row in the same trip, DTC P05FF62 is stored.
Interview the customer to check the vehicle conditions when the brake system warning light (red indicator) and brake system warning light (yellow indicator) illuminated.
Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.
Freeze Frame Data is only stored once when a DTC is stored.
If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused DTC P05FF62 to be stored based on the interview with the customer.
| Proceed to |
|---|
| NEXT |
NEXT
With the brake pedal released, confirm the brake pedal stroke sensor assembly output voltage.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 0.6 to 1.4 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
0.6 to 1.4 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>INSTALLATION
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>INSTALLATION
Turn the ignition switch off.
Mount a pedal effort gauge.
Turn the ignition switch to ON (READY) and depress the brake pedal once.
Depress the brake pedal after turning the ignition switch to ON (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).
Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 0.6 to 1.4 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
Perform this procedure in linear mode (switching solenoid (SSA) on).
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
|---|---|
| 50 (5, 11.2) | 1.20 to 1.90 |
| 100 (10, 22.5) | 1.42 to 2.12 |
| 150 (15, 33.7) | 1.61 to 2.31 |
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
|---|---|
| 50 (5, 11.2) | 1.17 to 1.87 |
| 100 (10, 22.5) | 1.37 to 2.07 |
| 150 (15, 33.7) | 1.55 to 2.25 |
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
|---|---|
| 50 (5, 11.2) | 1.20 to 1.90 |
| 100 (10, 22.5) | 1.42 to 2.16 |
| 150 (15, 33.7) | 1.61 to 2.31 |
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
|---|---|
| 50 (5, 11.2) | 1.17 to 1.87 |
| 100 (10, 22.5) | 1.37 to 2.07 |
| 150 (15, 33.7) | 1.55 to 2.25 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE PEDAL STROKE SENSOR (for RHD)>REMOVAL
Depress the brake pedal slowly and check the reaction force pressure sensor output values with respect to brake pedal depression force.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Reaction Force Pressure | Pressure value of stroke simulator | Min.: 0.00 MPa
Max.: 24.48 MPa |
Brake pedal released: 0.00 to 1.53 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Tester Display |
|---|
| Reaction Force Pressure |
Perform this procedure in linear mode (switching solenoid (SSA) on).
| Brake Effort
[N (kgf, lbf)] |
Reaction Force Pressure
[MPa] |
|---|---|
| 50 (5, 11.2) | 0.00 to 0.68 |
| 100 (10, 22.5) | 0.61 to 1.41 |
| 150 (15, 33.7) | 1.29 to 2.09 |
| 200 (20, 45.0) | 1.96 to 2.76 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| DTC P05FF62 is not output. | A |
| DTC P05FF62 is output. | B |
A
B
for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for HV Model RHD)>REMOVAL