This procedure is for troubleshooting when the brake system warning light (red indicator) remains on but no DTCs are output.
The skid control ECU (brake actuator assembly) controls the brake system warning light (red indicator) in the combination meter assembly via CAN communication.
After replacing the skid control ECU (brake actuator assembly), perform "Calibration".
Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.
Check that all of the following conditions required for the brake system warning light (red indicator) to turn off are met:
The brake fluid level in the brake master cylinder reservoir assembly is not low.
The vacuum inside the brake booster decreases.
When the vacuum inside the brake booster decreases, the brake system warning light (red indicator) comes on.
| Proceed to |
|---|
| NEXT |
NEXT
With a sufficient level of brake fluid, disconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector and confirm that the brake system warning light (red indicator) illuminates.
The brake system warning light (red indicator) does not turn off.
If the brake system warning light (red indicator) turns off, there is a short in the brake fluid level warning switch (brake master cylinder reservoir assembly) circuit.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the H21 combination meter assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H21-12 (SW) or A1-1 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the H21 combination meter assembly connector.
Reconnect the A1 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.
Perform the Active Test of the combination meter assembly using the GTS.
| Tester Display |
|---|
| Brake Warning |
Check the combination meter assembly.
The brake system warning light (red indicator) turns on or off in accordance with GTS operation.
| Result | Proceed to |
|---|---|
| OK (w/o Stop and Start System) | A |
| OK (w/ Stop and Start System) | B |
| NG | C |
A
B
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model RHD)>REMOVAL
C
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Inspect the vacuum warning switch assembly.
Click hereBrake>BRAKE SYSTEM (OTHER)>VACUUM WARNING SWITCH>ON-VEHICLE INSPECTION
The vacuum warning switch assembly is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A2 vacuum warning switch assembly connector.
Disconnect the H21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H21-8 (VCM) - A2-2 (+) | Always | Below 1 Ω |
| H21-8 (VCM) or A2-2 (+) - Body ground | Always | 10 kΩ or higher |
| A2-1 (E) - Body ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model RHD)>REMOVAL
NG