Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2020.11
RM37A0E _59 Vehicle Exterior _086899 WINDOW / GLASS _0416694 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, front camera system, lane control system, road sign assist system, pre-collision system or lighting system (EXT) may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56115A 1.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B564608

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the installation area of 2 new No. 2 windshield glass stoppers with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.
B564609C01
2.635,0.813 2.365,0.583 false 0.781,1.177 1.75,0.667 false 1.615,1.146 1.75,0.667 false 2.25,1.104 1.75,0.667 false 1.323,1.146 1.75,0.667 false 1.906,1.115 1.75,0.667 false 0.094,0.104 0.49,0.427 0.396,0.323 12 false *A 1.688,0.5 2,0.656 0.313,0.156 10 false *a 2.135,0.479 2.448,0.635 0.313,0.156 10 false *b 2.729,0.958 3.042,1.115 0.313,0.156 10 false a
*A Back Side
*a Ceramic Notch
*b Windshield Glass Edge Side


Install the 2 No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 13.7 to 14.7 mm (0.539 to 0.579 in.)


HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 75531F 3.INSTALL WINDSHIELD OUTSIDE UPPER MOULDING

a.

Using a brush or sponge, coat the installation area of a new windshield outside upper moulding with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the windshield outside upper moulding to the windshield glass as shown in the illustration.

B564611C01
1.573,1.146 1.49,1 true 3.469,1.156 3.563,0.99 true 0.292,0.125 0.76,0.417 0.469,0.292 12 false *A 1.573,1.156 1.885,1.313 0.313,0.156 10 false *a 3.344,1.177 3.594,1.344 0.25,0.167 10 true *a 2.198,1.427 2.354,1.625 0.156,0.198 10 false A 2.188,1.917 2.354,2.115 0.167,0.198 10 true A 4.938,0.76 5.365,1.021 0.427,0.26 10 false A-A 1.125,0.5 1.281,0.698 0.156,0.198 10 false a 1.375,0.396 1.531,0.594 0.156,0.198 10 false a 3.646,0.406 3.802,0.604 0.156,0.198 10 false a 3.854,0.469 4.01,0.667 0.156,0.198 10 false a 4.76,1.698 4.917,1.896 0.156,0.198 10 false b
*A Back Side - -
*a Alignment Position (Edge Of Curved Surface) - -


Reference Measurement / Standard Dimension:
Area Measurement Area Dimension
a 2.0 mm (0.0787 in.) b 7.0 mm (0.276 in.)



Hide 56117A 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of 3 new window glass adhesive dams with glass primer.

NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the window glass adhesive dam to the windshield glass as shown in the illustration.

B564612C01
0.49,3.26 0.635,3.156 true 4.281,3.292 4.063,3.146 true 5.688,2.385 5.969,2.135 true 2.813,2.385 2.813,1.99 true 0.302,0.219 0.677,0.458 0.375,0.24 12 false *A 2.042,1.635 2.198,1.833 0.156,0.198 10 false A 2.031,2.292 2.188,2.49 0.156,0.198 10 false A 5.083,1.01 5.49,1.344 0.406,0.333 10 false A-A 5.531,2.365 5.844,2.563 0.313,0.198 10 false *a 0.354,3.26 0.667,3.458 0.313,0.198 10 false *b 4.313,3.229 4.625,3.427 0.313,0.198 10 false *b 0.521,2.542 0.677,2.74 0.156,0.198 10 false a 0.927,2.604 1.083,2.802 0.156,0.198 10 false a 3.708,2.573 3.938,2.802 0.229,0.229 10 false b 4.146,2.521 4.344,2.74 0.198,0.219 10 false b 2.74,2.427 3.052,2.625 0.313,0.198 10 false *a
*A Back Side - -
*a Indicated Line *b Alignment Position (End of Indicated Line)


Reference Measurement:
Area Measurement Area Measurement
a 20.0 mm (0.787 in.) b 5.0 mm (0.197 in.)



c.

Install the 2 window glass adhesive dams to the windshield glass as shown in the illustration.

B564613C01
0.49,1.354 0.271,0.958 true 3.646,1.708 3.177,1.531 true 6.625,2.208 6.448,2.073 true 3.813,0.938 3.635,0.583 true 3.854,3.198 4.104,2.938 true 0.219,0.135 0.635,0.5 0.417,0.365 12 false *A 0.094,0.865 0.406,1.021 0.313,0.156 10 false *a 3.708,1.635 4.021,1.792 0.313,0.156 10 false *a 6.625,2.24 6.938,2.396 0.313,0.156 10 false *a 2.958,2.063 3.115,2.26 0.156,0.198 10 false A 3.438,1.969 3.594,2.167 0.156,0.198 10 false A 5.354,1.01 5.906,1.375 0.552,0.365 10 false A-A 3.469,0.5 3.781,0.656 0.313,0.156 10 false *b 3.708,3.188 4.021,3.344 0.313,0.156 10 false *b 4.24,0.615 4.396,0.813 0.156,0.198 10 false a 4.323,0.885 4.479,1.083 0.156,0.198 10 false a 4.583,2.625 4.74,2.823 0.156,0.198 10 false b 4.635,2.906 4.792,3.104 0.156,0.198 10 false b
*A Back Side - -
*a Indicated Line *b Alignment Position (End of Indicated Line)


Reference Measurement:
Area Measurement Area Measurement
a 5.0 mm (0.197 in.) b 8.0 mm (0.315 in.)



Hide 56153C 5.INSTALL FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of the front window inner center moulding is necessary.


a.
B514556C01
0.073,0.073 0.469,0.385 0.396,0.313 12 false *A 0.604,1.885 1,2.198 0.396,0.313 10 false A 0.521,2.25 0.917,2.563 0.396,0.313 10 false A 1.25,2.948 1.646,3.26 0.396,0.313 10 false A-A 1.573,3.177 1.969,3.49 0.396,0.313 10 false a
*A Back Side
V100155

Glass Primer


Using a brush or sponge, coat the installation area of a new front window inner center moulding with glass primer.

Standard Dimension:
Area Dimension
a 17.5 to 20.5 mm (0.689 to 0.807 in.)


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.



b.

Install the front window inner center moulding to the windshield glass as shown in the illustration.

B564610C01
1.198,2.792 1.052,2.656 1.052,2.656 1.26,2.688 false 3.469,2.792 3.615,2.646 3.615,2.646 3.417,2.698 false 2.26,2.781 2.26,2.698 2.26,2.698 2.51,2.698 true 2.417,2.698 2.417,2.781 true 1.76,1.938 1.917,2.135 0.156,0.198 10 false A 1.771,2.292 1.927,2.49 0.156,0.198 10 false A 4.927,0.573 5.385,0.833 0.458,0.26 10 false A-A 0.875,3.292 1.031,3.49 0.156,0.198 10 false a 1.146,3.385 1.302,3.583 0.156,0.198 10 false a 3.458,3.385 3.615,3.583 0.156,0.198 10 false a 3.74,3.271 3.896,3.469 0.156,0.198 10 false a 0.885,2.531 1.083,2.75 0.198,0.219 10 false *a 3.656,2.563 3.854,2.781 0.198,0.219 10 false *a 6.323,1.979 6.479,2.177 0.156,0.198 10 false b 0.24,0.198 0.615,0.438 0.375,0.24 12 false *A 2.531,2.635 2.729,2.854 0.198,0.219 10 false *b
*A Back Side - -
*a Alignment Mark (Ceramic Notch) *b Matchmark


Reference Measurement / Standard Dimension:
Area Measurement Area Dimension
a 2.0 mm (0.0787 in.) b 0 to 0.6 mm (0 to 0.0236 in.)


NOTICE:

Do not damage the front window inner center moulding.



Hide 6.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY

a.
B564600C01
1.313,1.667 1.313,1 1.313,1 1.646,1 true 1.313,1.167 1.646,1.167 true 1.24,1.688 1.5,1.896 0.26,0.208 10 true *a
*a Matchmark


Position the windshield glass sub-assembly.

i.

Using suction cups, place the windshield glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the windshield glass sub-assembly and vehicle body.

NOTICE:

Check that the windshield glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the windshield glass sub-assembly.



b.

Using a brush, coat the installation surface on the vehicle body with body primer.

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than specified is coated by accident, wipe off the body primer with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the adhesive application area with glass primer.

B564614C01
4.083,1.427 3.74,1.458 true 0.229,0.083 0.635,0.365 0.406,0.281 12 false *A 4.115,1.333 4.427,1.49 0.313,0.156 10 false *a 1.896,0.417 2.052,0.615 0.156,0.198 10 false A 1.917,1.271 2.073,1.469 0.156,0.198 10 false A 0.885,1.521 1.073,1.74 0.188,0.219 10 false B 0.406,1.458 0.594,1.677 0.188,0.219 10 false B 1.854,1.938 2.042,2.156 0.188,0.219 10 false C 1.885,2.646 2.073,2.865 0.188,0.219 10 false C 4.917,2.75 5.25,3 0.333,0.25 10 false C-C 4.833,1.5 5.25,1.75 0.417,0.25 10 false B-B 4.75,0.083 5.25,0.417 0.5,0.333 10 false A-A 5.479,0.26 5.635,0.458 0.156,0.198 10 false a 6.115,1.458 6.271,1.656 0.156,0.198 10 false a 5.99,2.698 6.146,2.896 0.156,0.198 10 false a
*A Back Side - -
*a Adhesive Application Area - -
V100155

Glass Primer - -


Standard Dimension:
Area Dimension - -
a 8.0 mm (0.315 in.) or more - -


NOTICE:
·

Do not apply too much glass primer.

·

Allow the glass primer to dry for 3 minutes or more.

·

Throw away any leftover glass primer.



HINT:
·

Apply glass primer to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the glass primer with a clean piece of cloth before it dries.




d.

Apply adhesive to the windshield glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

B564615C01
3.479,1.219 3.917,1.125 false 0.156,0.135 0.542,0.406 0.385,0.271 12 false *A 1.688,0.135 1.844,0.333 0.156,0.198 10 false A 1.719,0.927 1.875,1.125 0.156,0.198 10 false A 0.292,1.104 0.458,1.302 0.167,0.198 10 false B 0.75,1.198 0.917,1.396 0.167,0.198 10 false B 0.563,1.448 0.729,1.646 0.167,0.198 10 false C 0.375,2.094 0.542,2.292 0.167,0.198 10 false C 1.74,1.583 1.906,1.781 0.167,0.198 10 false D 1.75,2.24 1.917,2.438 0.167,0.198 10 false D 1.177,2.49 1.521,2.76 0.344,0.271 10 false A-A 4.792,0.146 5.135,0.417 0.344,0.271 10 false B-B 4.708,1.313 5.052,1.583 0.344,0.271 10 false D-D 3.719,2.458 4.063,2.729 0.344,0.271 10 false C-C 3.938,1.021 4.25,1.219 0.313,0.198 10 false *a 1.854,3.604 2.01,3.802 0.156,0.198 10 false a 6.073,1.26 6.271,1.469 0.198,0.208 10 false b 5.667,2.51 5.865,2.719 0.198,0.208 10 false c 5.51,3.542 5.708,3.75 0.198,0.208 10 false d
*A Back Side - -
*a Adhesive Positioning Center - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension Area Dimension
a 9.5 mm (0.374 in.) b 5.0 mm (0.197 in.)
c 6.5 mm (0.256 in.) d 53.8 mm (2.12 in.)


HINT:

Apply adhesive to the ceramic notches.




e.
B564600C01
1.313,1.667 1.313,1 1.313,1 1.646,1 true 1.313,1.167 1.646,1.167 true 1.24,1.688 1.5,1.896 0.26,0.208 10 true *a
*a Matchmark


Install the windshield glass sub-assembly.

i.

Using suction cups, position the windshield glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass sub-assembly.




ii.

Lightly press the outer surface of the windshield glass sub-assembly to ensure that the windshield glass sub-assembly is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




f.

When replacing the windshield glass sub-assembly or front window inner center moulding with a new one:

i.
B514560N01
1.771,1.729 1.927,1.927 0.156,0.198 10 true A 1.802,2.188 1.958,2.385 0.156,0.198 10 true A 0.865,2.99 1.24,3.229 0.375,0.24 10 true A-A

Remove the 2 protective retainers from the front window inner center moulding.

NOTICE:

Do not damage the front window inner center moulding.


HINT:

Make sure to remove the protective retainers.




g.

w/ Windshield Deicer System:

i.

Connect the connector.



Hide 7.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 8.INSTALL ROOF HEADLINING ASSEMBLY

a.

Return the front section of the roof headlining assembly to its original position.


b.

Connect the connector.


Hide 74320 10.INSTALL VISOR ASSEMBLY LH

Hide 74325 11.INSTALL VISOR BRACKET COVER (for LH Side)

Hide 74610A 12.INSTALL ASSIST GRIP SUB-ASSEMBLY

Hide 74310 13.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74325 14.INSTALL VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62212B 15.INSTALL FRONT PILLAR GARNISH ASSEMBLY LH

Hide 62211U 16.INSTALL FRONT PILLAR GARNISH ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 81260A 17.INSTALL MAP LIGHT ASSEMBLY

Hide 8646C 18.INSTALL FORWARD RECOGNITION CAMERA

Hide 89941 19.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 75534 21.INSTALL WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 22.INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 55708 23.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 8646C 24.ADJUST FORWARD RECOGNITION CAMERA

a.

If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.

HINT:

Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.

Target Adjustment (One Time Recognition): Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Target Adjustment (Sequential Recognition): Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT