68948
1.INSTALL BACK DOOR DAMPER STAY LOWER BRACKET LH
68947
2.INSTALL BACK DOOR DAMPER STAY LOWER BRACKET RH
Use the same procedure as for the LH side.
68960
3.INSTALL BACK DOOR STAY ASSEMBLY LH (w/o Power Back Door)
68950C
4.INSTALL BACK DOOR STAY ASSEMBLY RH (w/o Power Back Door)
Use the same procedure as for the LH side.
68920
5.INSTALL POWER BACK DOOR UNIT SET ASSEMBLY LH (w/ Power Back Door)
68910A
6.INSTALL POWER BACK DOOR UNIT SET ASSEMBLY RH (w/ Power Back Door)
Use the same procedure as for the LH side.
7.INSTALL NO. 1 CAMERA CLEANER HOSE
When replacing the back door panel sub-assembly:
Remove the 2 pieces of tape that secure the rope passed through the inside of the back door panel sub-assembly.
|
Tape | - | - |
The rope will be used when installing the No. 1 camera cleaner hose. Leave the rope inside the back door panel sub-assembly.
Secure the rope with a diameter of 9.0 mm (0.354 in.) to the No. 1 camera cleaner hose with nonwoven tape as shown in the illustration.
| *a | Nonwoven Tape | *b | Rope |
| *c | Clamp | *d | Washer Hose |
Make sure that the rope is secured with nonwoven tape to prevent the rope from separating from the No. 1 camera cleaner hose when removing it.
As the No. 1 camera cleaner hose is likely to be caught in the narrow areas inside the back door panel sub-assembly, make sure to align the clamp and washer hose in a straight line and cover the edges of the washer hose with nonwoven tape.
A rope with a diameter of 8.0 mm (0.315 in.) or less may be caught in the gaps on the inside of the back door panel sub-assembly. Make sure to use a rope with a diameter of 9.0 mm (0.354 in.).
Pass the No. 1 camera cleaner hose through the inside of the back door panel sub-assembly as shown in the illustration.
|
Install in this Direction | - | - |
This step should not be performed with the back door panel sub-assembly removed from the vehicle.
Engage the clamp.
Connect the washer hose.
Engage the clamp to install the No. 1 camera cleaner hose.
867F2
8.INSTALL NO. 2 CAMERA CLEANER HOSE
Connect the No. 1 camera cleaner hose.
Engage the clamp hose to install the No. 2 camera cleaner hose.
85373R
9.INSTALL REAR WASHER (FROM JOINT TO NOZZLE) HOSE
Connect the No. 1 camera cleaner hose to install the rear washer (from joint to nozzle) hose.
85345R
10.INSTALL REAR WASHER NOZZLE
82184
11.INSTALL NO. 1 BACK DOOR WIRE
When replacing the back door panel sub-assembly:
Remove the 2 pieces of tape that secure the rope passed through the inside of the back door panel sub-assembly.
|
Tape | - | - |
The rope will be used when installing the No. 1 back door wire. Leave the rope inside the back door panel sub-assembly.
When replacing the No. 1 back door wire:
|
Tape |
Remove the clamp.
Secure the rope with a diameter of 9.0 mm (0.354 in.) to the No. 1 back door wire with nonwoven tape as shown in the illustration.
| *A | w/ Digital Inner Mirror | - | - |
| *a | Nonwoven Tape | *b | Rope |
| *c | Clamp | *d | Connector |
As conduction performance may degrade if adhesive from the nonwoven tape contacts the connecting parts of the connectors, cover the connectors with a plastic bag or similar before applying the nonwoven tape.
Make sure that the rope is secured with nonwoven tape to prevent the rope from separating from the No. 1 back door wire when removing it.
As the No. 1 back door wire is likely to be caught in the narrow areas inside the back door panel sub-assembly, make sure to align the clamp and connectors in a straight line and cover the edges of the connectors with nonwoven tape.
A rope with a diameter of 8.0 mm (0.315 in.) or less may be caught in the gaps on the inside of the back door panel sub-assembly. Make sure to use a rope with a diameter of 9.0 mm (0.354 in.).
Pass the No. 1 back door wire through the inside of the back door panel sub-assembly as shown in the illustration.
|
Install in this Direction | - | - |
This step should not be performed with the back door panel sub-assembly removed from the vehicle.
| *A | w/ Power Back Door |
Engage each clamp.
Connect each connector.
| *A | w/ Digital Inner Mirror |
Engage the 2 clamps.
Connect each connector to install the No. 1 back door wire.
12.INSTALL TELEVISION CAMERA ASSEMBLY WITH NOZZLE (w/o Digital Inner Mirror)
13.INSTALL TELEVISION CAMERA ASSEMBLY WITH NOZZLE (w/ Digital Inner Mirror)
14.INSTALL CUSHION
Engage the 2 claws to install a new cushion.
Use the same procedure for the RH side and LH side.
67282F
15.INSTALL BACK DOOR LOWER STOPPER LH
Engage the guide to install the back door lower stopper LH with the 2 bolts.
67281B
16.INSTALL BACK DOOR LOWER STOPPER RH
Use the same procedure as for the LH side.
89222A
17.INSTALL MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door)
81590A
18.INSTALL REAR LIGHT ASSEMBLY LH
81580D
19.INSTALL REAR LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
84280D
20.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)
84270G
21.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)
Use the same procedure as for the LH side.
69350P
22.INSTALL BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)
69350P
23.INSTALL BACK DOOR LOCK ASSEMBLY WITH COURTESY LIGHT SWITCH (w/ Power Back Door)
81270
24.INSTALL LICENSE PLATE LIGHT ASSEMBLY
Use the same procedure for the RH side and LH side.
Click hereVehicle Exterior>LIGHTING (EXT)>LICENSE PLATE LIGHT ASSEMBLY>INSTALLATION
76835A
25.INSTALL NO. 1 BACK DOOR FINISH PANEL PROTECTOR
|
Install in this Direction |
Engage the 2 guides and 2 claws to install the No. 1 back door finish panel protector as shown in the illustration.
84840G
26.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY
76832A
27.INSTALL BACK DOOR FINISH PANEL COVER LH
|
Install in this Direction |
Engage the guide and 2 claws to install the back door finish panel cover LH as shown in the illustration.
76831A
28.INSTALL BACK DOOR FINISH PANEL COVER RH
Use the same procedure as for the LH side.
86160Z
29.INSTALL REAR NO. 3 SPEAKER ASSEMBLY (for 11 Speakers)
85143R
30.INSTALL REAR WIPER MOTOR GROMMET
85110R
31.INSTALL REAR WIPER MOTOR ASSEMBLY
32.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY
85292A
33.INSTALL REAR WIPER ARM HEAD CAP
74811D
34.INSTALL DOOR PULL HANDLE
w/ Power Back Door:
Connect the connector.
|
Install in this Direction |
Engage the 7 claws to install the door pull handle as shown in the illustration.
64780A
35.INSTALL BACK DOOR TRIM PANEL ASSEMBLY
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 2 guides and 14 clips to install the back door trim panel assembly as shown in the illustration.
67848E
36.INSTALL BACK DOOR SERVICE HOLE COVER LH
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the 2 guides and 2 claws to install the back door service hole cover LH as shown in the illustration.
67847
37.INSTALL BACK DOOR SERVICE HOLE COVER RH
Use the same procedure as for the LH side.
81574
38.INSTALL CENTER STOP LIGHT COVER
81572
39.INSTALL CENTER STOP LIGHT GASKET
81570
40.INSTALL CENTER STOP LIGHT ASSEMBLY
64783F
41.INSTALL DECK TRIM POCKET COVER PLATE
|
Install in this Direction |
Engage the 2 guides as shown in the illustration.
|
Install in this Direction |
Engage the 4 clips to install the deck trim pocket cover plate as shown in the illustration.
85345R
42.INSPECT REAR WASHER NOZZLE
85345R
43.ADJUST REAR WASHER NOZZLE
44.INITIALIZE POWER BACK DOOR SYSTEM (w/ Power Back Door)
45.INSPECT POWER BACK DOOR SYSTEM (w/ Power Back Door)
46.PERFORM CALIBRATION (w/ Parking Assist Monitor System)
47.PERFORM CALIBRATION (w/ Panoramic View Monitor System)
48.ADJUST BACK DOOR
When the back door damper stay lower bracket is removed, it is necessary to perform back door position adjustment.
Click hereVehicle Exterior>DOOR / HATCH>BACK DOOR>ADJUSTMENT