Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2020.11
RM37A0E _58 Vehicle Interior _086884 DOOR LOCK _0417744 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Hide 69278C 5.REMOVE REAR DOOR INSIDE HANDLE BEZEL

Hide 67604 6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 67842E 7.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 69060A 8.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

a.
B563691C01
2.938,2.99 3.042,2.74 true 2.854,3.01 3.031,3.198 0.177,0.188 10 true *a
*a Release Plate
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, remove the 3 screws.


b.

Move the rear door lock with motor assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.


c.

When reusing the rear door lock with motor assembly:

i.
B563692

Remove the door lock wiring harness seal from the rear door lock with motor assembly.



Hide 69038A 9.REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY

a.
B563693

Using a screwdriver, disengage the 2 claws as shown in the illustration.


b.
B563694C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.


Hide 69740D 10.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B563695C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door lock remote control cable assembly as shown in the illustration.


Hide 69780B 11.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B563696C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door inside locking cable assembly as shown in the illustration.