The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
58441L
2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)
3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for 2GR-FKS:
Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL
for A25A-FXS, A25B-FXS:
Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL
4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
|
Protective Tape |
Apply protective tape to the rear door trim board sub-assembly as shown in the illustration.
Using a moulding remover, disengage the 2 clips, 2 claws and 5 guides as shown in the illustration.
Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.
69278C
5.REMOVE REAR DOOR INSIDE HANDLE BEZEL
Using a moulding remover, disengage the 3 claws to remove the rear door inside handle bezel.
67604
6.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.
Remove the 3 screws.
|
Place Hand Here |
|
Remove in this Direction |
Disengage the 9 clips as shown in the illustration.
|
Remove in this Direction |
Disengage the 4 claws and guide as shown in the illustration.
w/ Illumination:
Disengage the clamp.
Disconnect the connector.
| *1 | Rear Door Inside Lock/Unlock Knob Locking Cable |
| *2 | Rear Door Lock Open Lever Remote Control Cable |
|
Remove in this Direction |
Disconnect the rear door lock open lever remote control cable and rear door inside lock/unlock knob locking cable as shown in the illustration to remove the rear door trim board sub-assembly.
69206C
7.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the 3 claws to remove the rear door inside handle sub-assembly.
74222C
8.REMOVE REAR DOOR ARMREST COVER
|
Remove in this Direction |
Disengage the claw to remove the rear door armrest cover as shown in the illustration.
65908D
9.REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)
Remove the 7 screws.
Disengage 3 guides to remove the rear curtain sub-assembly.
65923E
10.REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)
Use the same procedure for both curtain hooks.
| *a | Protective Tape |
|
Insert Screwdriver Here |
Using a screwdriver with its tip wrapped with protective tape, push out the pin as shown in the illustration.
| *a | Protective Tape |
|
Insert Screwdriver Here |
Using a screwdriver with its tip wrapped with protective tape, disengage the pin.
|
Push |
|
Remove in this Direction |
Disengage the 2 claws to remove the curtain hook as shown in the illustration.
67674A
11.REMOVE REAR DOOR FRAME GARNISH
|
Remove in this Direction |
Using a clip remover, disengage the clip.
Disengage the 2 guides to remove the rear door frame garnish as shown in the illustration.
67676C
12.REMOVE NO. 2 REAR DOOR FRAME GARNISH
Disengage the 3 claws to remove the No. 2 rear door frame garnish.
86160B
13.REMOVE REAR SPEAKER ASSEMBLY
68640A
14.REMOVE REAR DOOR CHECK ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt, 2 nuts and rear door check assembly.
67872
15.REMOVE REAR DOOR WEATHERSTRIP
|
Double-sided Tape |
Using a clip remover, disengage the 28 clips, guide and remove the rear door weatherstrip.
68174A
16.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
|
Remove in this Direction |
Remove the rear door inner glass weatherstrip as shown in the illustration.
67848A
17.REMOVE NO. 1 REAR DOOR VENT SEAL
|
Remove in this Direction |
Disengage the 3 guides to remove the No. 1 rear door vent seal as shown in the illustration.
67225A
18.REMOVE QUARTER WINDOW UPPER STOP
|
Remove in this Direction |
Remove the quarter window upper stop as shown in the illustration.
67842E
19.REMOVE REAR DOOR SERVICE HOLE COVER
Disconnect the connector.
Disengage the 2 clamps.
Disengage the 7 clips and remove the rear door service hole cover.
68152C
20.REMOVE REAR DOOR GLASS RUN
Remove the rear door glass run.
67408E
21.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
|
Screw |
|
Bolt |
Remove the screw, 2 bolts and rear door window division bar sub-assembly.
68124B
22.REMOVE REAR DOOR QUARTER WINDOW GLASS
|
Remove in this Direction |
Remove the rear door quarter window glass as shown in the illustration.
68189
23.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP
Remove the rear door quarter window weatherstrip from the rear door quarter window glass.
68104
24.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
Connect the rear power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Move the rear door glass sub-assembly so that the door glass bolts can be seen.
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the rear power window regulator switch assembly.
Remove the 2 bolts.
Do not damage the rear door glass sub-assembly.
|
Remove in this Direction |
Remove the rear door glass sub-assembly as shown in the illustration.
Do not damage the rear door glass sub-assembly.
25.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
Disconnect the connector.
Remove the 6 nuts and rear door window regulator assembly.
69060A
26.REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY
69240
27.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
Disengage the 2 claws and move the lever as shown in the illustration.
|
Remove in this Direction |
Remove the rear door outside handle assembly as shown in the illustration.
69227M
28.REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using a T30 "TORX" socket wrench, loosen the screw.
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.
Disengage the 2 claws to remove the rear door outside handle cover.
69241G
29.REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD
Disengage the 2 claws and guide to remove the rear door front outside handle pad.
69242G
30.REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD
Disengage the claw and 3 guides to remove the rear door rear outside handle pad.
69204A
31.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Using a T30 "TORX" socket wrench, remove the screw.
|
Remove in this Direction |
Disengage the claw and guide to remove the rear door outside handle frame sub-assembly as shown in the illustration.
67836H
32.REMOVE REAR DOOR LOCK CHILD PROTECTION COVER
Disengage the 6 claws to remove the rear door lock child protection cover.
75740
33.REMOVE REAR DOOR BELT MOULDING ASSEMBLY
75762B
34.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING
75766B
35.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING
75764A
36.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING
75792
37.REMOVE DOOR WINDOW FRAME MOULDING CLIP
| *a | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.
67896
38.REMOVE REAR DOOR NO. 3 WEATHERSTRIP
Remove the rear door No. 3 weatherstrip.
|
Double-sided Tape | - | - |
67003C
39.REMOVE REAR DOOR PANEL CUSHION
Disengage the claw to remove the rear door panel cushion.
75078
40.REMOVE REAR DOOR LOWER OUTSIDE MOULDING SUB-ASSEMBLY
41.REMOVE REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY
75797G
42.REMOVE REAR DOOR UPPER OUTSIDE MOULDING PAD
67888A
43.REMOVE REAR DOOR NO. 2 WEATHERSTRIP
Disengage the 6 clips to remove the rear door No. 2 weatherstrip.
67846A
44.REMOVE REAR DOOR FRONT OUTSIDE SEAL
Disengage the 4 claws and guide to remove the rear door front outside seal.
67837C
45.REMOVE REAR DOOR DUST PROOF SEAL
Disengage the 3 claws to remove the 3 rear door dust proof seals.