This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
17169A
1.INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.
11452
2.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Using an 8 mm socket wrench, install the engine oil level dipstick guide to the camshaft housing sub-assembly with the bolt.
Install the engine oil level dipstick.
19500
3.INSTALL IGNITION COIL ASSEMBLY
23250E
4.INSTALL DIRECT FUEL INJECTOR ASSEMBLY
23814B
5.INSTALL FUEL DELIVERY PIPE
23250F
6.INSTALL PORT FUEL INJECTOR ASSEMBLY
82125N
7.INSTALL NO. 5 ENGINE WIRE
23291
8.INSTALL INJECTOR VIBRATION INSULATOR
23807V
9.INSTALL NO. 1 DELIVERY PIPE SPACER
23807
10.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
11.INSTALL WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.
82126A
12.INSTALL NO. 6 ENGINE WIRE
Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.
Engage the 2 clamps.
Connect the 4 connectors.
82219A
13.INSTALL SENSOR WIRE
Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.
Engage the 3 clamps.
Connect the 3 connectors.
16295
14.INSTALL NO. 7 WATER BY-PASS HOSE
Install the No. 7 water by-pass hose and slide the 2 clips to secure it.
23100X
15.TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
23801P
16.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
23100X
17.INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
23801P
18.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY
| *a | 17 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.
Do not adjust the torque in the loosening direction.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)
Using an 8 mm socket wrench, install the bolt.
23910A
19.CONNECT FUEL TUBE SUB-ASSEMBLY
17177
20.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
17111
21.INSTALL INTAKE MANIFOLD
16278
22.INSTALL NO. 2 WATER BY-PASS PIPE
Temporarily install the No. 2 water by-pass pipe to the cylinder block sub-assembly with the bolt (A).
Using an 8 mm socket wrench, temporarily install the No. 2 water by-pass pipe to the intake manifold with the 2 bolts (B).
Tighten the bolt (A).
Using an 8 mm socket wrench, tighten the 2 bolts (B).
16279
23.INSTALL NO. 3 WATER BY-PASS PIPE
Install the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.
Using an 8 mm socket wrench, connect the No. 3 water by-pass pipe to the intake manifold with the bolt.
25620
24.SET EGR VALVE ASSEMBLY
25680
25.INSTALL EGR COOLER ASSEMBLY
25620
26.INSTALL EGR VALVE ASSEMBLY
25601
27.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
22271
28.INSTALL THROTTLE BODY GASKET
22030
29.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
17141
30.INSTALL EXHAUST MANIFOLD
17118
31.INSTALL MANIFOLD STAY
17167
32.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
w/o Differential Pressure Sensor:
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 5 bolts.
w/ Differential Pressure Sensor:
Install the No. 1 exhaust manifold heat insulator to the exhaust manifold with the 3 bolts.
25706
33.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Differential Pressure Sensor)
| *a | Torque Wrench Fulcrum Length |
Using a 14 mm union nut wrench, install the No. 1 vacuum transmitting pipe sub-assembly to the exhaust manifold.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf).
Install the nut.
89481B
34.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)
16260
35.INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Install the water hose clamp bracket with the 2 bolts as shown in the illustration.
Temporarily tighten the bolt (A), and then fully tighten the 2 bolts in the order of (B) and (A).
| *a | Paint Mark |
| *b | 45° (Claw of Clip Location) |
Connect the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet and slide the clip to secure it.
Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet.
Make sure that the claws of the clip are within the location shown in the illustration.
Install the flow shutting valve (water by-pass hose assembly) with the bolt.
16207
36.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Install the No. 2 water by-pass pipe sub-assembly with the bolt.
Connect the No. 2 water by-pass pipe sub-assembly to the water by-pass outlet and slide the clip to secure it.
88370
37.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY
Using an E8 "TORX" socket wrench, temporarily install the compressor with motor assembly with the 2 stud bolts.
|
Bolt |
|
Nut |
Install the compressor with motor assembly with the bolt and 2 nuts.
Tighten the bolt and nuts in the order shown in the illustration.
43457
38.INSTALL DRIVE SHAFT BEARING BRACKET
Install the drive shaft bearing bracket with the 3 bolts.