88460
1.INSTALL COOLER CONDENSER ASSEMBLY (for Gasoline Model)
|
Install in this Direction |
Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.
Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.
Add 40 cc (1.35 fl. oz)
ND-OIL 12 or equivalent
88460
2.INSTALL COOLER CONDENSER ASSEMBLY (for HV Model)
|
Install in this Direction |
Engage the 2 guides to install the cooler condenser assembly as shown in the illustration.
Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.
Add 40 cc (1.35 fl. oz)
ND-OIL 11 or equivalent
88710
3.CONNECT AIR CONDITIONING TUBE ASSEMBLY (for Gasoline Model)
Remove the vinyl tape from the cooler condenser assembly and air conditioning tube assembly.
| *1 | Air Conditioning Tube Assembly |
| *2 | Piping Clamp |
| *a | Groove |
Install a new piping clamp to the air conditioning tube assembly.
Securely engage the piping clamp to the groove of the air conditioning tube assembly.
Do not open the piping clamp more than the diameter of the air conditioning tube assembly when installing it.
Do not install the piping clamp with the large diameter section facing the wrong direction.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the air conditioning tube assembly.
ND-OIL 12 or equivalent
Install the 2 O-rings to the air conditioning tube assembly.
Keep the O-rings and O-ring fitting surfaces free from foreign matter.
Connect the air conditioning tube assembly to the cooler condenser assembly.
| *a | Large Diameter Section of Piping Clamp | - | - |
Connect the parts by holding the pipe, not the piping clamp.
Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.
When inserting, make sure that a click sound is heard.
Check that the cooler condenser assembly is securely connected by pulling it.
88710
4.CONNECT AIR CONDITIONING TUBE ASSEMBLY (for HV Model)
Remove the vinyl tape from the cooler condenser assembly and air conditioning tube assembly.
| *1 | Air Conditioning Tube Assembly |
| *2 | Piping Clamp |
| *a | Groove |
Install a new piping clamp to the air conditioning tube assembly.
Securely engage the piping clamp to the groove of the air conditioning tube assembly.
Do not open the piping clamp more than the diameter of the air conditioning tube assembly when installing it.
Do not install the piping clamp with the large diameter section facing the wrong direction.
Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the air conditioning tube assembly.
ND-OIL 11 or equivalent
Install the 2 O-rings to the air conditioning tube assembly.
Keep the O-rings and O-ring fitting surfaces free from foreign matter.
Connect the air conditioning tube assembly to the cooler condenser assembly.
| *a | Large Diameter Section of Piping Clamp | - | - |
Connect the parts by holding the pipe, not the piping clamp.
Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.
When inserting, make sure that a click sound is heard.
Check that the cooler refrigerant liquid pipe A is securely connected by pulling it.
88703
5.CONNECT DISCHARGE HOSE SUB-ASSEMBLY (for Gasoline Model)
Remove the vinyl tape from the discharge hose sub-assembly and cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.
ND-OIL 12 or equivalent
Install the O-ring to the discharge hose sub-assembly.
Keep the O-ring and O-ring fitting surface free from foreign matter.
Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.
88703
6.CONNECT DISCHARGE HOSE SUB-ASSEMBLY (for HV Model)
Remove the vinyl tape from the discharge hose sub-assembly and cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.
ND-OIL 11 or equivalent
Install the O-ring to the discharge hose sub-assembly.
Keep the O-ring and O-ring fitting surface free from foreign matter.
Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.
G9010A
7.CONNECT RADIATOR ASSEMBLY (for HV Model)
for Inverter Coolant:
|
Install in this Direction |
Install the radiator assembly to its original position as shown in the illustration.
Do not apply excessive force to the No. 3 inverter cooling hose and No. 4 inverter cooling hose.
Engage the 2 claws.
Be careful not to damage the radiator assembly (for inverter coolant) or radiator assembly.
Install the 4 bolts.
16593B
8.INSTALL NO. 1 RADIATOR AIR GUIDE RH
|
Install in this Direction |
Engage the guide and claw to install the No. 1 radiator air guide RH as shown in the illustration.
Install the clip.
16595B
9.INSTALL NO. 1 RADIATOR AIR GUIDE LH
|
Install in this Direction |
Engage the 2 guides and claw to install the No. 1 radiator air guide LH as shown in the illustration.
Install the clip.
88790B
10.INSTALL THERMISTOR ASSEMBLY (w/o Grille Shutter)
53205
11.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 2GR-FKS)
53205
12.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for A25A-FXS, A25B-FXS)
17750A
13.INSTALL INLET AIR CLEANER ASSEMBLY (for 2GR-FKS)
17750A
14.INSTALL INLET AIR CLEANER ASSEMBLY (for A25A-FXS, A25B-FXS)
53510
15.INSTALL HOOD LOCK ASSEMBLY
for LHD:
Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY>INSTALLATION
for RHD:
Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY>INSTALLATION
52021
16.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
52611
17.INSTALL FRONT BUMPER ENERGY ABSORBER
18.INSTALL FRONT BUMPER ASSEMBLY (w/o Grille Shutter)
53019F
19.INSTALL RADIATOR SHUTTER SUB-ASSEMBLY (w/ Grille Shutter)
20.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
21.WARM UP ENGINE (for Gasoline Model)
22.WARM UP COMPRESSOR (for HV Model)
23.INSPECT FOR REFRIGERANT LEAK
53301
24.ADJUST HOOD SUB-ASSEMBLY