CYLINDER HEAD > INSTALLATION |
| 1. INSTALL CYLINDER HEAD GASKET |
![]() |
Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.
![]() |
Measure the piston protrusion of each cylinder at 2 points as shown in the illustration.
For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.
![]() |
Select a new cylinder head gasket.
| Mark | Thickness |
| A | 0.80 to 0.90 mm (0.0315 to 0.0354 in.) |
| B | 0.85 to 0.95 mm (0.0335 to 0.0374 in.) |
| C | 0.90 to 1.00 mm (0.0354 to 0.0394 in.) |
| D | 0.95 to 1.05 mm (0.0374 to 0.0413 in.) |
| E | 1.00 to 1.10 mm (0.0394 to 0.0433 in.) |
Select the largest piston protrusion value from the measurements made. Then select a new appropriate gasket according to the table below.
| Gasket Size | Piston Protrusion |
| Use A | 0.005 to 0.054 mm (0.0002 to 0.0021 in.) |
| Use B | 0.055 to 0.104 mm (0.0022 to 0.0041 in.) |
| Use C | 0.105 to 0.154 mm (0.0041 to 0.0061 in.) |
| Use D | 0.155 to 0.204 mm (0.0061 to 0.0080 in.) |
| Use E | 0.205 to 0.255 mm (0.0081 to 0.0100 in.) |
![]() |
Place the cylinder head on the cylinder block.
Place the cylinder head gasket on the cylinder block.
| 2. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Place the cylinder head on the cylinder head gasket.
Apply a light coat of engine oil on the threads and under the heads of the cylinder head bolts.
![]() |
Install and uniformly tighten the 18 cylinder head bolts, in several passes in the sequence shown in the illustration.
![]() |
Mark the front of the cylinder head bolts with paint.
Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration above.
Finally, tighten the cylinder head bolts by an additional 90°.
Check that the painted marks are now facing rearward.
| 3. INSTALL CAMSHAFT |
![]() |
Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
![]() |
Install the camshaft.
Apply MP grease to the thrust portion of the camshaft.
Place the camshaft on the cylinder head, facing the key groove upward.
![]() |
Align the timing marks (1 dot mark) of the camshaft drive and driven main gears, and set the No. 2 camshaft in place.
![]() |
Remove any old packing (FIPG) material from the camshaft bearing cap.
Apply seal packing to the specified areas shown in the illustration.
![]() |
Install the 5 bearing caps in their proper locations.
![]() |
Apply a light coat of engine oil on the threads and under the heads of the bearing cap bolts.
Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.
Install the camshaft oil seal.
| 4. INSPECT VALVE CLEARANCE |
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Specified Condition |
| Intake | 0.20 to 0.30 mm (0.008 to 0.012 in.) |
| Exhaust | 0.35 to 0.45 mm (0.014 to 0.018 in.) |
Turn the crankshaft 360° to set the No. 4 cylinder to TDC/compression.
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Specified Condition |
| Intake | 0.20 to 0.30 mm (0.008 to 0.012 in.) |
| Exhaust | 0.35 to 0.45 mm (0.014 to 0.018 in.) |
| 5. ADJUST VALVE CLEARANCE |
Drain coolant.
Remove the fan shroud.
Remove the No. 1 timing belt cover.
Remove the timing belt.
Remove the camshaft timing pulley.
Remove the No. 1 timing belt idler.
Remove the No. 2 timing belt cover.
Remove the camshafts.
Remove the valve lifters.
![]() |
Using a micrometer, measure the thickness of the removed lifter.
Calculate the thickness of a new lifter so that the valve clearance is within the specified range.
| A | B | C |
| New lifter thickness | Used lifter thickness | Measured valve clearance |
Select a new lifter with a thickness as close as possible to the calculated values.
Install the selected valve lifter.


| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
| 06 | 5.060 mm (0.1992 in.) | 30 | 5.300 mm (0.2087 in.) | 54 | 5.540 mm (0.2181 in.) |
| 08 | 5.080 mm (0.2000 in.) | 32 | 5.320 mm (0.2094 in.) | 56 | 5.560 mm (0.2189 in.) |
| 10 | 5.100 mm (0.2008 in.) | 34 | 5.340 mm (0.2102 in.) | 58 | 5.580 mm (0.2197 in.) |
| 12 | 5.120 mm (0.2016 in.) | 36 | 5.360 mm (0.2110 in.) | 60 | 5.600 mm (0.2205 in.) |
| 14 | 5.140 mm (0.2024 in.) | 38 | 5.380 mm (0.2118 in.) | 62 | 5.620 mm (0.2213 in.) |
| 16 | 5.160 mm (0.2031 in.) | 40 | 5.400 mm (0.2126 in.) | 64 | 5.640 mm (0.2220 in.) |
| 18 | 5.180 mm (0.2039 in.) | 42 | 5.420 mm (0.2134 in.) | 66 | 5.660 mm (0.2228 in.) |
| 20 | 5.200 mm (0.2047 in.) | 44 | 5.440 mm (0.2142 in.) | 68 | 5.680 mm (0.2236 in.) |
| 22 | 5.220 mm (0.2055 in.) | 46 | 5.460 mm (0.2150 in.) | 70 | 5.700 mm (0.2244 in.) |
| 24 | 5.240 mm (0.2063 in.) | 48 | 5.480 mm (0.2157 in.) | 72 | 5.720 mm (0.2252 in.) |
| 26 | 5.260 mm (0.2071 in.) | 50 | 5.500 mm (0.2165 in.) | 74 | 5.740 mm (0.2260 in.) |
| 28 | 5.280 mm (0.2079 in.) | 52 | 5.520 mm (0.2173 in.) | - | - |


| Lifter No. | Specified Condition | Lifter No. | Specified Condition | Lifter No. | Specified Condition |
| 06 | 5.060 mm (0.1992 in.) | 30 | 5.300 mm (0.2087 in.) | 54 | 5.540 mm (0.2181 in.) |
| 08 | 5.080 mm (0.2000 in.) | 32 | 5.320 mm (0.2094 in.) | 56 | 5.560 mm (0.2189 in.) |
| 10 | 5.100 mm (0.2008 in.) | 34 | 5.340 mm (0.2102 in.) | 58 | 5.580 mm (0.2197 in.) |
| 12 | 5.120 mm (0.2016 in.) | 36 | 5.360 mm (0.2110 in.) | 60 | 5.600 mm (0.2205 in.) |
| 14 | 5.140 mm (0.2024 in.) | 38 | 5.380 mm (0.2118 in.) | 62 | 5.620 mm (0.2213 in.) |
| 16 | 5.160 mm (0.2031 in.) | 40 | 5.400 mm (0.2126 in.) | 64 | 5.640 mm (0.2220 in.) |
| 18 | 5.180 mm (0.2039 in.) | 42 | 5.420 mm (0.2134 in.) | 66 | 5.660 mm (0.2228 in.) |
| 20 | 5.200 mm (0.2047 in.) | 44 | 5.440 mm (0.2142 in.) | 68 | 5.680 mm (0.2236 in.) |
| 22 | 5.220 mm (0.2055 in.) | 46 | 5.460 mm (0.2150 in.) | 70 | 5.700 mm (0.2244 in.) |
| 24 | 5.240 mm (0.2063 in.) | 48 | 5.480 mm (0.2157 in.) | 72 | 5.720 mm (0.2252 in.) |
| 26 | 5.260 mm (0.2071 in.) | 50 | 5.500 mm (0.2165 in.) | 74 | 5.740 mm (0.2260 in.) |
| 28 | 5.280 mm (0.2079 in.) | 52 | 5.520 mm (0.2173 in.) | - | - |
Install the camshaft.
Install the No. 2 timing belt cover.
Install the No. 1 timing belt idler.
Install the camshaft timing pulley.
Install the timing belt.
Install the No. 1 timing belt cover.
Install the fan shroud.
Add engine coolant.
| 6. INSTALL CYLINDER BLOCK INSULATOR (w/ EGR Cooler) |
Install the cylinder block insulator to the cylinder head.
| 7. INSTALL NO. 2 TIMING BELT COVER |
![]() |
Apply seal packing (FIPG) to the specified areas shown in the illustration.
Install the No. 2 timing belt cover with the 4 bolts and nut.
| 8. INSTALL CAMSHAFT TIMING PULLEY |
![]() |
Install the camshaft timing pulley.
Fasten the bolt of the camshaft timing pulley by holding the camshaft with a wrench.
| 9. CONNECT WIRE HARNESS |
| 10. INSTALL EXHAUST MANIFOLD |
Install a new gasket, manifold, 8 new collars and 8 spacers to the cylinder head with 8 new nuts.
| 11. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
Install the No. 1 compressor mounting bracket with the 4 bolts.
| 12. CONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System) |
Connect the cooler compressor with the 4 bolts.
| 13. INSTALL TURBOCHARGER SUB-ASSEMBLY (w/ EGR Cooler) |
| 14. INSTALL TURBOCHARGER SUB-ASSEMBLY (w/o EGR Cooler) |
| 15. INSTALL INJECTOR ASSEMBLY (w/ EGR Cooler) |
| 16. INSTALL INJECTOR ASSEMBLY (w/o EGR Cooler) |
| 17. INSTALL TIMING BELT |
| 18. INSTALL COMMON RAIL ASSEMBLY (w/ EGR Cooler) |
| 19. INSTALL COMMON RAIL ASSEMBLY (w/o EGR Cooler) |
| 20. INSTALL GLOW PLUG ASSEMBLY (w/ EGR Cooler) |
| 21. INSTALL GLOW PLUG ASSEMBLY (w/o EGR Cooler) |
| 22. INSTALL INTAKE MANIFOLD (w/ EGR Cooler) |
| 23. INSTALL INTAKE MANIFOLD (w/ EGR System without EGR Cooler) |
| 24. INSTALL INTAKE MANIFOLD (w/o EGR System) |
| 25. TIGHTEN FUEL TANK CAP ASSEMBLY |
| 26. ADD ENGINE OIL |
Wipe the oil pan and drain plug before installing the plug.
Install a new gasket and the drain plug.
Add new oil.
| Item | Capacity |
| Drain and refill with oil filter change | 6.9 liters (7.3 US qts, 6.1 Imp. qts) |
| Drain and refill without oil filter change | 6.6 liters (7.0 US qts, 5.8 Imp. qts) |
| Dry fill | 7.4 liters (7.8 US qts, 6.5 Imp. qts) |
Install the oil filler cap.
| 27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 28. BLEED AIR FROM FUEL SYSTEM |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.
Start the engine.
When the engine can be started, proceed to the next step.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to the procedures above). Then start the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Clear the DTCs (Click here).
Start the engine.*1
![]() |
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*2
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*3
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Clear the DTCs (Click here).
Repeat steps *1 to *3.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
| 29. PERFORM REGISTRATION |
Perform registration of the injector compensation codes .
Perform pilot quantity learning .
| 30. INSPECT FOR OIL LEAK |
| 31. INSPECT FOR FUEL LEAK |
![]() |
Check that there are no leaks from any part of the fuel system when the engine is stopped. If there is fuel leakage, repair or replace parts as necessary.
Start the engine and check that there are no leaks from any part of the fuel system. If there is fuel leakage, repair or replace parts as necessary.
Disconnect the return hose from the common rail.
Start the engine and check for fuel leaks from the return pipe.
If there is fuel leakage, replace the common rail.
Connect the intelligent tester to the DLC3.
Start the engine and push the intelligent tester main switch ON.
Select the Fuel Leak test from the Active Test mode on the intelligent tester.
If the intelligent tester is not available, fully depress the accelerator pedal quickly. Increase the engine speed to the maximum and maintain that speed for 2 seconds. Repeat this operation several times.
Check that there are no leaks from any part of the fuel system.
Reconnect the return hose to the common rail.
| 32. INSPECT ENGINE OIL LEVEL |
Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick's low and full level marks.
If the oil level is low, check for leakage and add oil up to the full level mark.
| 33. INSTALL NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner) |
Install the No. 1 engine under cover with the 4 bolts.