ECD SYSTEM (w/ EGR Cooler) > Engine Difficult to Start or Stalling |
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Main fault | Decrease in performance (foreign matter is stuck) | |
| Symptoms | Lack of power, black smoke | |
| Data List | MAF | |
| ||
| Symptom: Main fault |
| |
| Data List |
| |
| Main fault |
| |
| Symptoms | Lack of power (when vehicle starting, when heavy load) (Black smoke is not emitted when racing while vehicle stopped) | |
| Data List | MAP (inside intake air pressure), Target Booster Pressure
| |
| Diagnostic Point |
| |
| Main fault | Blockage | |
| Symptoms | Lack of power (high engine speed, when heavy load) | |
| Data List | MAP (inside intake air pressure) When the accelerator is fully depressed, if MAP is 20 kPa lower than Target Booster Pressure for more than 5 seconds then a lack of power will be felt. | |
| Main fault | Open circuit, glow plug relay fault | |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) | |
| Data List | Check the glow plug indicator light | |
| Diagnostic Point | Try to measure the resistance of the glow plug | |
| Main fault | Battery is depleted | |
| Symptoms | Difficult to start (cannot crank, crank speed is low), horn is quiet. | |
| Data List | Battery Voltage When cranking, battery voltage is below 5 V | |
| Main fault | Damaged, seized up | |
| Symptoms | Cannot crank, crank speed is low, strange noise | |
| Main fault | Loss of compression | |
| Symptoms | Rough idle (lack of power always) | |
| Data List | Engine Speed of Cyl
| |
| Main fault | Starter system malfunction | |
| Symptoms | Difficult to start | |
| Data List | Starter Signal
| |
Diesel Injection
| Main fault | - | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
| |
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. | |
| Main fault | Blockage | |
| Symptoms | Difficult to start, engine stalling, rough idle, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | Even if Fuel Press is less than Target Common Rail Pressure, a DTC will not be stored. | |
| Main fault | Blockage | |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Injection Feedback Val
| |
| Main fault | Does not completely close | |
| Symptoms | Difficult to start, engine stall, rough idle, lack of power | |
| Main fault | Circuit fault: The fuel injector does not open. | |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Same as fuel injector | |
| Diagnostic Trouble Code | When the EDU has a fault, some DTCs may be stored. | |
| Main fault | Open circuit, decrease in performance (foreign matter is stuck) | |
| Symptoms | Difficult to start, rough idle, engine stall, lack of power | |
| Data List | Fuel Press, Target Common Rail Pressure
| |
| Diagnostic Trouble Code | When the fuel pressure sensor has a fault, some DTCs may be stored. | |
| Main fault | - | |
| Symptoms | Difficult to start, rough idle (especially when cold) | |
Diesel EGR
| Main fault |
| |
| Symptoms |
| |
| Data List | Actual EGR Valve Pos., Target EGR Pos.
| |
Diesel Throttle
| Main fault | Stuck, does not move smoothly | |
| Symptoms |
| |
| Data List |
| |
| Data List Related to Starting Trouble |
| Explanation of Symptom |
| Starting Trouble | For good starting it is essential to have:
With problems such as a depleted battery, the crankshaft speed can become low, or if the engine compression is leaking, the compression pressure will not rise and there will be difficulty starting. When the engine is cold, even if there is compression heat, it will escape from the combustion chamber. For this reason, when the engine is started when it is cold, the glow plugs heat the compressed air. Also, after starting the engine, by charging the glow plugs for a fixed time set according to the engine coolant temperature, diesel knocking and white smoke are prevented. The quantity of fuel injected is determined by the fuel pressure and also the amount of time the fuel injector is open. |
| Trouble Area Chart According to Problem Cause |


| 1.CHECK ENGINE CRANKING CONDITION |
Check the engine cranking condition.
| Result | Proceed to |
| Does not crank at all. | A |
Low cranking speed.
| B |
| Cranking is OK. | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK BATTERY CONDITION |
Check the battery condition .
|
| ||||
| OK | |
| 3.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Check if the normal starting screen appears (check whether communication with the ECM is possible).
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (CLUTCH SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Clutch Switch.
Read the value displayed on the tester.
| Tester Display | Condition | Specified Condition |
| Clutch Switch | Clutch pedal depressed | ON |
| Result | Proceed to |
| OK | A |
| NG | B |
|
| ||||
| A | |
| 5.READ ALL OUTPUT DTCS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Utility / All Codes.
| Result | Proceed to |
| No DTC is output | A |
| DTCs related to engine are output | B |
|
| ||||
| A | ||
| ||
| 6.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL) |
Check if the fuel level is low.
| Result | Proceed to |
| The indicator (fuel warning light) is not illuminated | A |
| The indicator (fuel warning light) is illuminated | B |
|
| ||||
| A | |
| 7.CHECK INITIALIZATION (FUEL SUPPLY PUMP) |
When the engine does not start or another problem such as rough idling is present, perform initialization and check to see if the problem symptoms disappear. If the problem symptoms do not disappear, perform the next procedure.
| NEXT | |
| 8.READ OUTPUT DTC (RELATED TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| No DTC is output | A |
| DTCs related to engine are output | B |
|
| ||||
| A | |
| 9.TAKE SNAPSHOT DURING STARTING AND IDLING |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items with the intelligent tester during "ignition switch ON (5 seconds) → Starting → Idling (10 seconds)".
| NEXT | |
| 10.CHECK SNAPSHOT (TARGET PUMP SCV CURRENT) |
Check Target Pump SCV Current in the snapshot taken when the engine was starting.
| Result | Proceed to |
| Target Pump SCV Current is 3000 mA or more | A |
| Target Pump SCV Current is less than 3000 mA | B |
|
| ||||
| B | |
| 11.CHECK SNAPSHOT (FUEL PRESS) |
Check Fuel Press in the snapshot taken when the engine was starting.
| Result | Proceed to |
2 seconds after Starter Signal turns from OFF to ON, Fuel Press is less than 20000 kPa
| A |
| 2 seconds after Starter Signal turns from OFF to ON, Fuel Press is 50000 kPa or more | B |
| Except above | C |
|
| ||||
|
| ||||
| A | |
| 12.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS) |
![]() |
Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.*1
Start the engine.
When the engine can be started, proceed to step *2.
If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases (refer to step *1). Then start the engine.
Turn the ignition switch off.*2
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (Click here).
Start the engine.*3
Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.*4
Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak.*5
Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time.*6

Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
When no DTCs are output, the air bleeding is completed. Proceed to step *8.
If any DTCs are output, proceed to step *7.
Clear DTCs (Click here).*7
Repeat steps *3 to *6.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.*8
Start the engine.
Read the Fuel Press values while cranking and idling the engine.
| Result | Proceed to |
| The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON. | B |
| Except above | A |
|
| ||||
| A | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
![]() |
Disconnect the S8 suction control valve connector.
Disconnect the E8 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S8-1 - E8-2 (PCV+) | Always | Below 1 Ω |
| S8-2 - E8-1 (PCV-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| S8-1 or E8-2 (PCV+) - Body ground | Always | 10 kΩ or higher |
| S8-2 or E8-1 (PCV-) - Body ground | Always | 10 kΩ or higher |
Reconnect the suction control valve connector.
Reconnect the ECM connector.
|
| ||||
|
| ||||
| 14.INSPECT COMMON RAIL ASSEMBLY |
Inspect the common rail assembly (Click here).
|
| ||||
| OK | |
| 15.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP |
Disconnect the inlet hose from the fuel supply pump.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump.
|
| ||||
| OK | |
| 16.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
| NEXT | |
| 17.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 18.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 19.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Start the engine.
Read the Fuel Press values while cranking and idling the engine.
| Result | Proceed to |
| The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON. | B |
| Except above | A |
|
| ||||
| A | ||
| ||
| 20.INSPECT FUEL INJECTOR (INSPECTION FOR VALVE CLOSING PROBLEM) |
Remove the glow plug assembly for all the cylinders (Click here).
Visually check if there is fuel on the glow plugs.
| Result | Proceed to |
| No fuel on glow plugs | A |
| Fuel on glow plugs | B |
Install the glow plug assembly (Click here).
|
| ||||
| A | |
| 21.REPLACE COMMON RAIL |
Replace the common rail (Click here).
| NEXT | |
| 22.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 23.READ VALUE USING INTELLIGENT TESTER (FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Start the engine.
Read the Fuel Press values while cranking and idling the engine.
| Result | Proceed to |
| The engine cannot be started or the engine can be started but Fuel Press is less than 20000 kPa 2 seconds after the starter signal changes from OFF to ON. | B |
| Except above | A |
|
| ||||
| A | ||
| ||
| 24.INSPECT INJECTOR COMPENSATION CODE |
Read the injector compensation code .
|
| ||||
| OK | |
| 25.CHECK DATA LIST |
![]() |
Check Injection Feedback Val # and Injection Volume in the snapshot taken when the engine was idling.
| Result | Proceed to |
Injection Feedback Val #1 to #4 are more than 3 mm3/st
| A |
| Injection Feedback Val #1 to #4 are 3 mm3/st or less Injection Volume is more than 10 mm3/st | B* |
| Injection Feedback Val #1 to #4 are 3 mm3/st or less Injection Volume is 10 mm3/st or less | C |
|
| ||||
|
| ||||
| A | |
| 26.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.
| NEXT | |
| 27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
|
| ||||
|
| ||||
| 28.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 29.REPLACE FUEL INJECTOR OF MALFUNCTIONING CYLINDER |
Replace the fuel injector (Click here).
|
| ||||
| 30.CHECK TEMPERATURE WHEN STARTING TROUBLE OCCURS |
Check the temperature when starting trouble occurs.
| Result | Proceed to |
| Difficult to start only for cold engine. | A |
| Difficult to start both for cold and warmed up engine. | B |
|
| ||||
| A | |
| 31.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 32.INSPECT GLOW PLUG ASSEMBLY (RESISTANCE) |
![]() |
Disconnect the glow plug wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Glow plug terminal - Body ground | 20°C (68°F) | Approximately 0.95 Ω |
|
| ||||
| OK | |
| 33.CHECK FUEL QUALITY |
Check that fuel with a low cetane number is used.
| NEXT | |
| 34.CHECK ENGINE STARTING CONDITION |
Check whether the engine can be started.
| Result | Proceed to |
| The engine can be started. | A |
| There is no initial combustion even when the engine can be cranked. | B |
|
| ||||
| A | |
| 35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the difficulty starting has been successfully repaired by starting the engine.
| NEXT | ||
| ||
| 36.CHECK SNAPSHOT |
| NEXT | |
| 37.INSPECT INJECTOR DRIVER (EDU POWER SOURCE) |
![]() |
Disconnect the I17 injector driver (EDU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| I17-2 (+B) - I17-3 (GND) | Ignition switch ON | 11 to 14 V |
Reconnect the injector driver (EDU) connector.
|
| ||||
| OK | |
| 38.INSPECT FUEL INJECTOR |
| NEXT | ||
| ||
| 39.REPLACE FUEL INJECTORS OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
| NEXT | |
| 40.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 41.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation codes .
Perform the fuel injector pilot quantity learning .
| NEXT | |
| 42.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Start the engine.
Read the Fuel Press values while cranking and idling the engine.
| NEXT | ||
| ||
| 43.CHECK AND REPAIR OR REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and repair or replace the clogged fuel pipe.
|
| ||||
| 44.ADD FUEL |
Add fuel.
| NEXT | |
| 45.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 46.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Start the engine.
Read the Fuel Press values while cranking and idling the engine.
| NEXT | ||
| ||
| 47.CHECK VC OUTPUT CIRCUIT |
Check the VC output circuit (Click here).
| NEXT | |
| 48.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Check if the normal starting screen appears (check whether communication with the ECM is possible).
|
| ||||
| OK | ||
| ||
| 49.CHECK ECM POWER SOURCE CIRCUIT |
Check the ECM power source circuit (Click here).
| NEXT | |
| 50.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Check if the normal starting screen appears (check whether communication with the ECM is possible).
|
| ||||
| OK | ||
| ||