DTC C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH |
DTC C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH |
DTC C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH |
DTC C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH |
DTC C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) |
DTC C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) |
DTC C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |

| DTC Code | DTC Detection Condition | Trouble Area |
| C1235/35 C1236/36 C1238/38 C1239/39 | When either condition below is met:
|
|
| C1275/75 C1276/76 C1277/77 C1278/78 | Detected only during Test Mode. | Skid control rotor |
| 1.INSPECT EACH SPEED SENSOR |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.

Disconnect each speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (FR+) - Body ground | Always | 10 kΩ or higher |
| 2 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (FL+) - Body ground | Always | 10 kΩ or higher |
| 2 (FL-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 4 - Body ground | Always | 10 kΩ or higher |
| 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 2 - Body ground | Always | 10 kΩ or higher |
| 1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 - Body ground | Always | 10 kΩ or higher |
| 2 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for front speed sensor) | B |
| NG (for rear speed sensor) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - EACH SPEED SENSOR) |
for Front Speed Sensor:

Disconnect the skid control ECU connector.
Disconnect the front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S35-7 (FR+) - S5-1 (FR+) | Always | Below 1 Ω |
| S35-7 (FR+) - Body ground | Always | 10 kΩ or higher |
| S35-6 (FR-) - S5-2 (FR-) | Always | Below 1 Ω |
| S35-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S35-19 (FL+) - S4-1 (FL+) | Always | Below 1 Ω |
| S35-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| S35-18 (FL-) - S4-2 (FL-) | Always | Below 1 Ω |
| S35-18 (FL-) - Body ground | Always | 10 kΩ or higher |
for Rear Speed Sensor:

Disconnect the skid control ECU connector.
for Type A and B:
Disconnect the BE1 rear speed sensor connector.
for Type C:
Disconnect the S40 and/or S41 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S35-5 (RL+) - BE1-2 | Always | Below 1 Ω |
| S35-4 (RL-) - BE1-1 | Always | Below 1 Ω |
| BE1-2 - Body ground | Always | 10 kΩ or higher |
| BE1-1 - Body ground | Always | 10 kΩ or higher |
| BE1-1 - BE1-2 | Always | 10 kΩ or higher |
| BE1-1 - BE1-3 | Always | 10 kΩ or higher |
| BE1-1 - BE1-4 | Always | 10 kΩ or higher |
| BE1-2 - BE1-3 | Always | 10 kΩ or higher |
| BE1-2 - BE1-4 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S35-17 (RR+) - BE1-4 | Always | Below 1 Ω |
| S35-16 (RR-) - BE1-3 | Always | Below 1 Ω |
| BE1-4 - Body ground | Always | 10 kΩ or higher |
| BE1-3 - Body ground | Always | 10 kΩ or higher |
| BE1-3 - BE1-4 | Always | 10 kΩ or higher |
| BE1-3 - BE1-1 | Always | 10 kΩ or higher |
| BE1-3 - BE1-2 | Always | 10 kΩ or higher |
| BE1-4 - BE1-1 | Always | 10 kΩ or higher |
| BE1-4 - BE1-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S35-5 (RL+) - S40-2 | Always | Below 1 Ω |
| S35-4 (RL-) - S40-1 | Always | Below 1 Ω |
| S40-2 - Body ground | Always | 10 kΩ or higher |
| S40-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| S35-17 (RR+) - S41-2 | Always | Below 1 Ω |
| S35-16 (RR-) - S41-1 | Always | Below 1 Ω |
| S41-2 - Body ground | Always | 10 kΩ or higher |
| S41-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT SKID CONTROL ECU (SENSOR INPUT) |
![]() |
for Front Speed Sensor:
Connect the skid control ECU connector.
Disconnect the front speed sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| S5-1 (FR+) - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| S4-1 (FL+) - Body ground | Ignition switch ON | 8 to 14 V |
for Rear Speed Sensor:

Connect the skid control ECU connector.
for Type A and B:
Disconnect the BE1 rear speed sensor connector.
for Type C:
Disconnect the S40 and/or S41 rear speed sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| BE1-4 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| BE1-2 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| S41-2 - Body ground | Ignition switch ON | 8 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| S40-2 - Body ground | Ignition switch ON | 8 to 14 V |
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC output | A |
| DTC not output | B |
|
| ||||
| A | |
| 5.CHECK SPEED SENSOR TIP |
Turn the ignition switch off.
Remove the front and/or rear speed sensor (for front speed sensor: Click here, for rear speed sensor: Click here).
Check the speed sensor tip.
| Result | Proceed to |
| OK | A |
| NG (for front speed sensor) | B |
| NG (for rear speed sensor) | C |
|
| ||||
|
| ||||
| A | |
| 6.CHECK SKID CONTROL ROTOR |
Remove the front and/or rear skid control rotor (for front skid control rotor: Click here, for rear skid control rotor: Click here).
Check the skid control rotors.
| Result | Proceed to |
| OK | A |
| NG (for front skid control rotor) | B |
| NG (for rear skid control rotor) | C |
|
| ||||
|
| ||||
| A | |
| 7.REPLACE SPEED SENSOR |
Turn the ignition switch off.
Replace the front and/or rear speed sensor (for front speed sensor: Click here, for rear speed sensor: Click here).
| NEXT | |
| 8.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC output | A |
| DTC not output | B |
|
| ||||
| A | |
| 9.REPLACE SKID CONTROL ROTOR |
Turn the ignition switch off.
Replace the front and/or rear skid control rotor (for front skid control rotor: Click here, for rear skid control rotor: Click here).
| NEXT | |
| 10.RECONFIRM DTC |
Clear the DTC(s) (Click here).
Start the engine.
Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Result | Proceed to |
| DTC output | A |
| DTC not output | B |
|
| ||||
| A | ||
| ||