DTC P2006 Intake Manifold Runner Control Stuck Closed (Bank 1) |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| After warming up engine, drive vehicle at an engine speed of 3200 rpm or more with high load for 1 minute or more.* | When actual intake air volume detected by mass air flow meter continues to be smaller than volume estimated from boost pressure and intake air temperature sensor, ECM determines that swirl control valve is stuck closed (1 trip detection logic). |
|

| *1 | ECM | *2 | Swirl Control Valve |
| *3 | Vacuum Pump | *4 | Vacuum Switching Valve (for Swirl Control Valve) |
| *5 | Swirl Control Valve Actuator | - | - |

| 1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2006) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P2006 | A |
| P2006 and other DTCs | B |
|
| ||||
| A | |
| 2.CHECK AIR INTAKE SYSTEM |
Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.
| Result | Proceed to |
| Leaks and/or blockages exist in the intake system | A |
| No leaks or blockages in the intake system | B |
|
| ||||
| A | |
| 3.REPAIR OR REPLACE AIR INTAKE SYSTEM |
Repair or replace the malfunctioning part in the air intake system.
|
| ||||
| 4.CHECK INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION) |
Check the movement of the swirl control valve immediately after starting the engine.

| *1 | Swirl Control Valve | - | - |
|
| ||||
| OK | |
| 5.READ VALUE USING INTELLIGENT TESTER (MAF AND MAP) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and MAF.
Take a snapshot when the engine speed is maintained at 4000 rpm with no load.
Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.
| Result | Proceed to |
| MAF 84 gm/s or more and MAP 117 kPa or higher | C |
| MAP below 90 kPa | B |
| Except above | A |
|
| ||||
|
| ||||
| A | |
| 6.CLEAN MASS AIR FLOW METER |
Remove any deposits adhering to the mass air flow meter.
|
| ||||
| 7.CHECK AND REPLACE TURBOCHARGER SUB-ASSEMBLY |
Check the turbocharger sub-assembly (Click here).
Replace the turbocharger sub-assembly (Click here).
|
| ||||
| 8.CHECK CONNECTION OF VACUUM HOSE |
Check the connection of the swirl control valve system vacuum hose.
|
| ||||
| OK | |
| 9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE) |
![]() |
Disconnect the vacuum hoses from the VSV for swirl control valve.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the VSV operation when it is operated using the intelligent tester.
| Tester Operation | Specified Condition |
| VSV ON | Air from port E flows out through port F |
| VSV OFF | Air from port E flows out through air filter |
Reconnect the vacuum hoses.
|
| ||||
| OK | |
| 10.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Inspect the electric EGR control valve assembly (Click here).
|
| ||||
|
| ||||
| 11.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY |
Replace the electric EGR control valve assembly (Click here).
| NEXT | |
| 12.INSPECT INTAKE MANIFOLD (SWIRL CONTROL VALVE OPERATION) |
Inspect the intake manifold (swirl control valve) (Click here).
|
| ||||
|
| ||||
| 13.REPAIR OR REPLACE VACUUM HOSE |
Repair or replace the vacuum hose.
|
| ||||
| 14.REPLACE INTAKE MANIFOLD |
Replace the intake manifold (swirl control valve) (Click here).
|
| ||||
| 15.REPLACE VACUUM CONTROL VALVE SET |
Replace the vacuum control valve set.
| NEXT | |
| 16.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR SWIRL CONTROL VALVE) |
![]() |
Disconnect the vacuum hoses from the vacuum switching valve (for Swirl Control Valve).
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Swirl Control Valve.
Check the VSV operation when it is operated using the intelligent tester.
| Tester Operation | Specified Condition |
| VSV ON | Air from port E flows out through port F |
| VSV OFF | Air from port E flows out through air filter |
Reconnect the vacuum hoses.
|
| ||||
|
| ||||
| 17.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and MAF.
Take a snapshot when the engine speed is maintained at 4000 rpm with no load.
Read the values of "MAP" and "MAF" in the Data List using the snapshot review function.
| NEXT | ||
| ||