Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY

ENGINE ASSEMBLY > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.



1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



3. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts and No. 1 engine under cover.



4. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 2 bolts and No. 2 engine under cover.



5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.



6. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A112147E01



7. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)
  1. for 2WD:
  2. for 4WD:


8. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
  1. for 2WD:
  2. for 4WD:


9. DRAIN POWER STEERING FLUID


10. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Remove the bolt, nut and battery clamp.



11. REMOVE BATTERY


12. REMOVE BATTERY TRAY


13. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the MAF meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



14. REMOVE RADIATOR ASSEMBLY
(Click here)


15. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY


    A111785
  1. Remove the 3 bolts, 2 nuts and engine cover.



16. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR


    A111786
  1. Disconnect the IAT sensor connector.

  1. Disconnect the manifold absolute diesel pressure sensor connector.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.



    A111787
  1. Loosen the 2 clamps.



    A112764
  1. Remove the 4 bolts and CAC.



17. REMOVE STARTER ASSEMBLY
  1. for DENSO Made: (Click here)
  2. for BOSCH Made: (Click here)


18. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


19. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)


C098708E01
  1. Place matchmarks on the yoke and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and disconnect the propeller shaft.



    F052086E01
  1. Place matchmarks on the yoke and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



20. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


21. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
    Text in Illustration 
    *1
    Stopper



    B278059E01
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge



22. DISCONNECT HOSES AND CONNECTORS


G035294E01
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.



    A238474E01
  1. Disconnect the 3 EDU connectors.



    A247346E01
  1. Disconnect the turbo motor driver connector.

  1. Disconnect the 3 TCM connectors.

  1. Disconnect the 4 ECM connectors.



    G035298E01
  1. Disconnect the 2 fuel hoses.

  1. Disconnect the vacuum pump hose.

  1. Disconnect the oil reservoir to pump hose.



    G034367E04
  1. Using a union nut wrench, disconnect the pressure feed tube.



23. DISCONNECT HEATER HOSE
  1. Disconnect the 2 heater hoses.



24. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



25. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
  1. for 2WD: (Click here)
  2. for 4WD: (Click here)


26. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
  1. for 2WD: (Click here)
  2. for 4WD: (Click here)


27. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)


D029616E03
  1. Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



28. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.



29. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114803
  1. Remove the 8 bolts and flywheel.



30. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114804
  1. Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel and ring gear.



31. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.



32. REMOVE ENGINE ASSEMBLY


    A224109E02
  1. Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    HINT:
    Part No.
    No. 1 engine hanger
    12284-30020
    No. 2 engine hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    NOTICE:
    Install the engine hangers with new bolts.



    A098988E01
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



33. INSTALL ENGINE TO ENGINE STAND


34. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.



35. REMOVE NO. 1 TIMING BELT COVER


A015094E01
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. Remove the 6 bolts and timing belt cover.



36. REMOVE TIMING BELT


A070549E02
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.



    A070550E01
  1. Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.



  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A070551E02
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks.



37. REMOVE CRANKSHAFT PULLEY


    A072413E02
  1. Using SST, remove the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A072414E02
  1. Using SST, remove the pulley.

    SST
    09213-58014  
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



38. REMOVE COMPRESSOR INLET ELBOW


A110341
  1. Remove the bolt from the ventilation pipe.

  1. Move the clamp so that the hose can be disconnected.

  1. Disconnect the ventilation pipe from the cylinder head cover.

  1. Disconnect the 2 connectors from the turbocharger.

  1. Remove the harness clamp's clip from the inlet elbow.

  1. Remove the 2 nuts, inlet elbow and gasket.



39. REMOVE NO. 1 TURBO INSULATOR
  1. Remove the bolt and insulator.



40. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


A110342
  1. Remove the 2 bolts and heat insulator.



41. REMOVE NO. 1 TURBO WATER HOSE


A098815E01
  1. Move the 2 clamps and disconnect the 2 hoses.



42. REMOVE TURBINE OUTLET ELBOW


A098816E01
  1. Remove the 3 nuts, outlet elbow and gasket.



43. REMOVE TURBOCHARGER STAY


A099944E02
  1. Remove the 3 bolts and stay.



44. DISCONNECT TURBO OIL INLET PIPE SUB-ASSEMBLY


A098817E02
  1. Remove the 2 bolts, 2 nuts, union bolt, inlet pipe and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A.



45. REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER


    A236847
  1. Remove the 8 nuts, 8 collars, 8 spacers and exhaust manifold with turbocharger as shown in the illustration.



46. REMOVE NO. 2 IDLE PULLEY ASSEMBLY


    A233180
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.



47. REMOVE GENERATOR ASSEMBLY


A125326
  1. Disconnect the terminal cap.

  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



48. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.



49. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.



50. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 1 intercooler support bracket.



51. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 2 intercooler support bracket.



52. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



53. REMOVE WATER INLET


    A097634E01
  1. for Automatic transmission:
    Remove the bolt and disconnect the clamp.



    A097637E01
  1. Remove the 3 bolts and inlet.



54. REMOVE THERMOSTAT


55. REMOVE WATER OUTLET


    A233596
  1. Remove the 2 bolts, water outlet and gasket.



56. REMOVE NO. 1 GLOW PLUG CONNECTOR
  1. Remove the nut and wire harness.

  1. Remove the 4 screw grommets, 4 nuts and glow plug connector.



57. REMOVE GLOW PLUG ASSEMBLY


A111830
  1. Using a 12 mm deep socket wrench, remove the 4 glow plugs.



58. REMOVE MANIFOLD STAY


A099622E01
  1. Remove the 2 bolts and manifold stay.



59. REMOVE DIESEL THROTTLE BODY ASSEMBLY


    A111790
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the throttle control motor connector.



    A111832
  1. Remove the 2 bolts, 2 nuts, throttle body and gasket.



60. REMOVE VACUUM SWITCHING VALVE BRACKET


    A110298
  1. Disconnect the 2 connectors.

  1. Disconnect the vacuum hoses from the 3 locations.

  1. Remove the 2 bolts and bracket.



61. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET


A114779E02
  1. Remove the 3 bolts and No. 2 intake air connector bracket.



62. REMOVE INTAKE AIR CONNECTOR
  1. Remove the 2 nuts, bolt, air connector and gasket.



63. REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY


A099621E01
  1. Remove the 2 bolts, 2 nuts, pipe and 2 gaskets.



64. REMOVE EGR VALVE ASSEMBLY
  1. Remove the electric EGR control valve and gasket.



65. REMOVE OIL FILTER SUB-ASSEMBLY


B011502E02
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



66. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



    A231803E01
  1. Remove the bolt and No. 2 injection pipe clamp.

  1. Remove the 2 nuts and No. 3 injection pipe clamp.

  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



67. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY


    A098893E01
  1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.



    A231804E01
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



68. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.



    A098898E05
  1. Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.



69. REMOVE FUEL INLET PIPE SUB-ASSEMBLY
  1. Remove the engine oil level dipstick.



    G036615E01
  1. Remove the bolt and clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring engine oil level dipstick guide.



    A098969E03
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



70. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.



    A231856
  1. Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve and fuel pressure sensor.



71. REMOVE FUEL SUPPLY PUMP ASSEMBLY


    G036615E01
  1. Remove the bolt and clamp.

  1. Remove the bolt and oil dipstick guide.



    A098969E02
  1. Using union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



    A098895E01
  1. Disconnect the 2 fuel hoses.



    A098896E01
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley using SST.

    SST
    09213-58013  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold or carry the pump by holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



72. REMOVE ENGINE OIL LEVEL DIPSTICK


73. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the bolt, engine oil level dipstick guide and O-ring.



74. REMOVE INTAKE MANIFOLD


A098944E01
  1. Remove the 4 bolts, 2 nuts, intake manifold and gasket.



75. REMOVE OIL COOLER COVER SUB-ASSEMBLY


A038741E01
  1. Disconnect the oil pressure switch connector and wire harness.

  1. Remove the 13 bolts, 2 nuts and oil cooler cover.



76. REMOVE VACUUM PUMP ASSEMBLY


    A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



77. REMOVE VANE PUMP ASSEMBLY


    A233594
  1. Remove the 2 nuts, vane pump and O-ring.



78. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and crankshaft position sensor.



79. REMOVE CAMSHAFT POSITION SENSOR
  1. Remove the bolt and camshaft position sensor.



80. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.



81. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A233592E01
  1. Remove the 2 nuts and 2 front engine mounting insulators.



82. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH


    A233593E01
  1. Remove the 4 bolts and No. 1 front engine mounting bracket.



83. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and No. 1 front engine mounting bracket.