Security Indicator Light Does not Blink
Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
- When the engine immobiliser system is set, the security indicator light assembly blinks continuously, but does not illuminate if the engine immobiliser system is not set.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When replacing the transponder key ECU assembly, refer to Registration.
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When replacing the transponder key ECU assembly, refer to Registration.
| 1. CHECK FOR DTC |
Check for DTCs (Click here).
- OK:
- DTC is not output.
|
|
||||
| OK | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT) |
Check that the security indicator light assembly illuminates when operating it with the Active Test (Click here).
Immobiliser Tester Display
Test Part
Control Range
Diagnostic Note
Security Indicator
Security indicator light
ON/OFF
The test is possible when the following condition is met: - The key is in the ignition key cylinder.
- OK:
- Security indicator light assembly can be turned on and off using the intelligent tester.
- The key is in the ignition key cylinder.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS) |
Turn the ignition switch off.
- HINT:
- When using the intelligent tester with the ignition switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the intelligent tester and vehicle begins.
Using the intelligent tester, read the Data List (Click here).
Immobiliser Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Immobiliser
Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset
Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.
- OK:
- Set (the key is not inserted in the ignition key cylinder) and Unset (the key is inserted in the ignition key cylinder) appear on the screen according to the key insertion condition.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU AND BODY GROUND) |
Disconnect the S10 security indicator light assembly connector.
Disconnect the T21 transponder key ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S10-2 - T21-8 (IND)
Always
Below 1 Ω
S10-1 - Body ground
Always
Below 1 Ω
S10-2 or T21-8 (IND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. REPLACE SECURITY INDICATOR LIGHT ASSEMBLY |
Temporarily replace the security indicator light assembly with a new or normally functioning one (Click here).
| NEXT | |
| 6. CHECK SECURITY INDICATOR LIGHT ASSEMBLY |
When the immobiliser is set (the ignition switch is off), check that the security indicator light assembly blinks.
- OK:
- Security indicator light assembly blinks.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND) |
Disconnect the T21 transponder key ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
T21-16 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
T21-1 (+B) - Body ground
Always
11 to 14 V
T21-2 (IG) - Body ground
Ignition switch off
Below 1 V
Ignition switch ON
11 to 14 V
| *a |
Front view of wire harness connector (to Transponder Key ECU Assembly) |
|
|
||||
| OK | ||
| ||
