2014 Hilux · Service Manual SECURITIES

Security Indicator Light Does not Blink

Circuit diagnosis · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

  1. When the engine immobiliser system is set, the security indicator light assembly blinks continuously, but does not illuminate if the engine immobiliser system is not set.

WIRING DIAGRAM

B278724E02

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the transponder key ECU assembly, refer to Registration.
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC is not output.



NG
Go to DIAGNOSTIC TROUBLE CODE CHART (Click here)
OK


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
  1. Check that the security indicator light assembly illuminates when operating it with the Active Test (Click here).

    Immobiliser 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Indicator
    Security indicator light
    ON/OFF
    The test is possible when the following condition is met:
    1. The key is in the ignition key cylinder.

    OK:
    Security indicator light assembly can be turned on and off using the intelligent tester.



NG
Go to step 4
OK


3. READ VALUE USING INTELLIGENT TESTER (ENGINE IMMOBILISER SYSTEM STATUS)
  1. Turn the ignition switch off.

    HINT:
    When using the intelligent tester with the ignition switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds until communication between the intelligent tester and vehicle begins.

  1. Using the intelligent tester, read the Data List (Click here).

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Immobiliser
    Engine immobiliser system status determined by transponder key ECU assembly / Set or Unset
    Set: Engine immobiliser set (engine start prohibited [no key in ignition key cylinder])
    Unset: Engine immobiliser unset (engine start permitted [key inserted in ignition key cylinder])
    When the engine immobiliser system does not change to the unset state, this item can be used to determine if the cause is the transponder key ECU assembly.

    OK:
    Set (the key is not inserted in the ignition key cylinder) and Unset (the key is inserted in the ignition key cylinder) appear on the screen according to the key insertion condition.



NG
Go to step 7
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

4. CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - TRANSPONDER KEY ECU AND BODY GROUND)
  1. Disconnect the S10 security indicator light assembly connector.

  1. Disconnect the T21 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S10-2 - T21-8 (IND)
    Always
    Below 1 Ω
    S10-1 - Body ground
    Always
    Below 1 Ω
    S10-2 or T21-8 (IND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE SECURITY INDICATOR LIGHT ASSEMBLY
  1. Temporarily replace the security indicator light assembly with a new or normally functioning one (Click here).


NEXT


6. CHECK SECURITY INDICATOR LIGHT ASSEMBLY
  1. When the immobiliser is set (the ignition switch is off), check that the security indicator light assembly blinks.

    OK:
    Security indicator light assembly blinks.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY
OK

END (SECURITY INDICATOR LIGHT IS DEFECTIVE)

7. CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)

  1. B274403E05
    Disconnect the T21 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T21-16 (GND) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T21-1 (+B) - Body ground
    Always
    11 to 14 V
    T21-2 (IG) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY


← Security Indicator Light Does not Blink (Aug 2012 – Jul 2013)INSPECTION (from Jun 2011) →