2014 Hilux · Service Manual BRAKE

C1405 Open or Short in Front Speed Sensor RH Circuit

Diagnostic trouble codes · Vehicles built Nov 2011 – Mar 2012

Also covers:

Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTCs C1401 and C1402 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
C1405
C1406
Either condition is met:
  1. An open in the speed sensor signal circuit continues for 0.5 seconds or more.
  2. With the IG1 terminal voltage at 9.5 V or higher, the sensor power supply voltage decreases for 0.5 seconds or more.
  1. Front speed sensor RH/LH
  2. Speed sensor circuit
  3. Skid control ECU (Brake actuator assembly)

HINT:
  1. DTC C1405 is for the front speed sensor RH.
  2. DTC C1406 is for the front speed sensor LH.


WIRING DIAGRAM

C241007E04

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Check the speed sensor signal after replacement (Click here).
  3. Before disconnecting the connector, make sure that there are no problems with the connection.
  4. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
  1. Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Speed Open
    Front speed sensor RH open circuit detection / Error or Normal
    Normal
    -
    FL Speed Open
    Front speed sensor LH open circuit detection / Error or Normal
    Normal
    -

    OK:
    Normal (there are no momentary interruptions).

    HINT:
    Perform the above inspection before removing the sensor or disconnecting a connector.



NG
Go to step 4
OK


2. READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
  1. Turn the ignition switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List, and then drive the vehicle.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.
    FL Wheel Speed
    Front speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Actual wheel speed
    No large fluctuations when driving at a constant speed.

  1. Check the speed value output from the speed sensor displayed on the intelligent tester.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK


3. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.

  1. Check if the same DTC is output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    S35-7 (FR+) - S5-1 (FR+)
    Always
    Below 1 Ω
    S35-7 (FR+) - Body ground
    Always
    10 kΩ or higher
    S35-6 (FR-) - S5-2 (FR-)
    Always
    Below 1 Ω
    S35-6 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    S35-19 (FL+) - S4-1 (FL+)
    Always
    Below 1 Ω
    S35-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    S35-18 (FL-) - S4-2 (FL-)
    Always
    Below 1 Ω
    S35-18 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK TERMINAL VOLTAGE (FR+, FL+ TERMINAL)
  1. Turn the ignition switch off.

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the speed sensor connector.

  1. C190626E05
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for RH 
    Tester Connection
    Switch Condition
    Specified Condition
    S5-1 (FR+) - Body ground
    Ignition switch ON
    8 to 14 V
    for LH 
    Tester Connection
    Switch Condition
    Specified Condition
    S4-1 (FL+) - Body ground
    Ignition switch ON
    8 to 14 V

    Text in Illustration 
    *A
    for RH
    *B
    for LH
    *a
    Front view of wire harness connector
    (to Front Speed Sensor)
    Result 
    Result
    Proceed to
    OK
    A
    NG
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPLACE FRONT SPEED SENSOR (Click here)


← C1405 Open or Short in Front Speed Sensor RH Circuit (+ C1406) (Jun 2011 – Oct 2011)C1405 Open or Short in Front Speed Sensor RH Circuit (+ C1406) (Apr 2012 – Jul 2012) →