Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio Receiver Type)
Radio Broadcast cannot be Received (Bad Reception)
Circuit diagnosis · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
WIRING DIAGRAM
INSPECTION PROCEDURE
1. CHECK IF RADIO AUTO-SEARCH FUNCTIONS PROPERLY
Check the radio automatic station search function by activating it.
OK:
Automatic station search function stops on a station.
NG
OK
2. CHECK OPTIONAL COMPONENTS
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
OK:
Optional components are installed.
NOTICE:
Do not remove optional components without permission of the customer.
NG
OK
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)
3. CHECK RADIO ANTENNA
for 2 Speakers:
Remove the antenna with holder assembly from the antenna cord sub-assembly (Click here ).
except 2 Speakers:
Remove the roof antenna pole sub-assembly from the amplifier antenna assembly (Click here ).
Turn the ignition switch to ACC with the radio receiver assembly connector connected.
Place a screwdriver, thin wire or other metal object on the amplifier antenna threaded installation position for the antenna with holder assembly (for 2 Speakers) or roof antenna pole sub-assembly (except 2 Speakers), and check that noise can be heard from the speakers.
OK:
Noise occurs.
NG
OK
4. CHECK RADIO RECEIVER ASSEMBLY (ANTENNA)
Remove the antenna connector from the radio receiver assembly.
Turn the ignition switch to ACC with the radio receiver assembly connector connected.
Turn on the radio and turn into AM mode.
Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.
OK:
Noise occurs.
NG
OK
5. INSPECT RADIO RECEIVER ASSEMBLY
Disconnect the RA radio receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
5 (ANT+) - Body ground
Ignition switch ACC, radio switch on and FM or AM selected
11 to 14 V
Result
Result
Proceed to
OK (for 2 Speakers)
A
OK (except 2 Speakers)
B
NG
C
B
C
A
6. CHECK ANTENNA CORD SUB-ASSEMBLY
Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally.
OK:
Radio broadcasts can be received normally.
NG
OK
END (ANTENNA CORD SUB-ASSEMBLY IS DEFECTIVE)
7. CHECK ANTENNA WITH HOLDER ASSEMBLY
Check that the antenna with holder assembly is securely installed.
OK:
The antenna with holder assembly is installed properly.
NG
REINSTALL ANTENNA WITH HOLDER ASSEMBLY (Click here )
OK
8. CHECK ANTENNA WITH HOLDER ASSEMBLY
Replace the antenna with holder assembly and check if radio broadcasts can be received normally (Click here ).
OK:
Radio broadcasts can be received normally.
NG
OK
END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)
9. CHECK ANTENNA CORD SUB-ASSEMBLY
Disconnect the radio receiver assembly connector.
Remove the antenna connector from the antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
RA-3 (MAIN) - 2
Always
Below 1 Ω
RA-5 (ANT+) - 3
Always
Below 1 Ω
RA-3 (MAIN) - Body ground
Always
10 kΩ or higher
RA-5 (ANT+) - Body ground
Always
10 kΩ or higher
Text in Illustration
*a
Front view of wire harness connector (to Radio Receiver Assembly)
*b
Front view of wire harness connector (to No. 2 Antenna Cord Sub-assembly)
NG
OK
10. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
Remove the antenna connector from the antenna cord sub-assembly.
Remove the antenna connector from the antenna with holder assembly.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Specified Condition
2 - 2
Always
Below 1 Ω
3 - 3
Always
Below 1 Ω
2 - Body ground
Always
10 kΩ or higher
3 - Body ground
Always
10 kΩ or higher
Text in Illustration
*a
Front view of wire harness connector to Antenna Cord Sub-assembly)
*b
Front view of wire harness connector (to Antenna with Holder Assembly)
NG
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here )
OK
11. CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
Check that the roof antenna pole sub-assembly is securely installed (Click here ).
OK:
The roof antenna pole sub-assembly is installed properly.
NG
REINSTALL ROOF ANTENNA POLE SUB-ASSEMBLY (Click here )
OK
12. CHECK ANTENNA WITH HOLDER ASSEMBLY
Replace the antenna with holder assembly and check if radio broadcasts can be received normally (Click here ).
OK:
Radio broadcasts can be received normally.
NG
OK
END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)
13. CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally (Click here ).
OK:
Radio broadcasts can be received normally.
NG
OK
END (ROOF ANTENNA POLE SUB-ASSEMBLY IS DEFECTIVE)