2014 Hilux · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Aug 2013

WIRING DIAGRAM

E277657E04

INSPECTION PROCEDURE


1. CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result 
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A


2. CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    Result 
    Result
    Proceed to
    Optional components are not installed
    A
    Optional components are installed
    B

    NOTICE:
    Do not remove optional components without the permission of the customer.



B
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)
A


3. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E245523
    Preparation for check
    1. Disconnect the antenna connector from the navigation receiver assembly.

  1. Check for noise

    1. Turn the ignition switch to ACC with the navigation receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speakers.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4. INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Disconnect the navigation receiver assembly connector.

  1. E188455E38
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    5 (ANT+) - Body ground
    Ignition switch ACC
    Radio switch on and AM or FM selected
    11 to 14 V



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


5. CHECK ANTENNA CORD SUB-ASSEMBLY

  1. E278669E01
    Disconnect the navigation receiver assembly connector.

  1. Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    RA-3 (MAIN) - 2
    Always
    Below 1 Ω
    RA-5 (ANT+) - 3
    Always
    Below 1 Ω
    RA-3 (MAIN) - Body ground
    Always
    10 kΩ or higher
    RA-5 (ANT+) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    *b
    Front view of wire harness connector
    (to No. 2 Antenna Cord Sub-assembly)



NG
REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


6. CHECK NO. 2 ANTENNA CORD SUB-ASSEMBLY
  1. Disconnect the antenna connector from the antenna cord sub-assembly.

  1. Disconnect the antenna connector from the antenna with holder assembly.

  1. E276821E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 - 2
    Always
    Below 1 Ω
    3 - 3
    Always
    Below 1 Ω
    2 - Body ground
    Always
    10 kΩ or higher
    3 - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Antenna with Holder Assembly)
    *b
    Front view of wire harness connector
    (to Antenna Cord Sub-assembly)



NG
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


7. CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
  1. Check that the roof antenna pole sub-assembly is securely installed (Click here).

    OK:
    The roof antenna pole sub-assembly is installed properly.



NG
CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY (Click here)
OK


8. CHECK ANTENNA WITH HOLDER ASSEMBLY
  1. Replace the antenna with holder assembly (Click here).

  1. Check if radio broadcasts can be received normally.

    OK:
    Radio broadcasts can be received normally.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

END (ANTENNA WITH HOLDER ASSEMBLY IS DEFECTIVE)


← CD Sound Skips (from Aug 2013)Illumination for Panel Switch does not Come on with Tail Switch ON (from Aug 2013) →