2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)

4. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)

5. DRAIN ENGINE COOLANT (w/ Intercooler)

NOTICE:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.


    A112147E01


6. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts and 2 compression springs.

  1. Disconnect the front pipe from the outlet pipe and remove the gasket.

  1. Remove the front pipe from the pipe support.


7. REMOVE FRONT FENDER APRON SEAL UPPER
  1. Remove the 5 clips and front fender apron seal upper.


8. REMOVE FRONT FENDER SEAL
  1. Remove the 5 clips and front fender seal.


9. REMOVE VENTILATION HOSE HEAT INSULATOR (w/o Intercooler)
  1. Remove the 2 bolts and ventilation hose heat insulator.


10. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)
(Click here)

11. REMOVE AIR CLEANER ASSEMBLY

  1. w/ Mass Air Flow Meter:

    1. Disconnect the mass air flow meter connector and detach the wire harness clamp.

      A311928E01

      Text in Illustration 
      *A
      w/ Intercooler
      *B
      w/o Intercooler

    2. Loosen the hose clamp, and then remove the No. 1 air cleaner hose from the turbocharger sub-assembly.

    3. w/o Intercooler:
      Slide the clamp and disconnect the ventilation hose from the cylinder head cover sub-assembly.

    4. Remove the 2 bolts and air cleaner assembly.

  1. w/o Mass Air Flow Meter:

    1. A311929
      Detach the clamp and disconnect the intake air temperature sensor connector.

    2. Loosen the hose clamp, and then remove the air cleaner hose from the turbocharger sub-assembly.

    3. Slide the clamp and disconnect the ventilation hose from the cylinder head cover sub-assembly.

    4. Remove the 2 bolts and air cleaner assembly.


12. REMOVE VENTILATION PIPE (w/ Intercooler)

  1. A288742
    for Type A:
    Slide the 2 clamps and disconnect the No. 12 water by-pass hose and No. 13 water by-pass hose from the ventilation pipe.

  1. A288747E02
    Remove the bolt and ventilation pipe.
    Text in Illustration 
    *A
    for Type B
    *B
    for Type A


13. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o Intercooler)

  1. w/ No. 1 Engine Cover

    1. A099256E03
      Detach the 4 claws from the pins of the engine cover bracket and remove the No. 1 engine cover sub-assembly.
      Text in Illustration 
      *1
      No. 1 Engine Cover Sub-assembly
      *2
      Claw
      *3
      Pin

    2. Remove the 2 bolts and engine cover bracket.

  1. A111789
    Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the No. 2 air cleaner pipe sub-assembly together with the 2 air hoses.


14. REMOVE COMPRESSOR INLET ELBOW (w/ Intercooler)

  1. A288737
    Disconnect the 2 connectors and detach the wire harness clamp.

  1. for Type A:

    1. A291249
      Slide the clamp and disconnect the No. 1 turbo water hose from the cylinder block sub-assembly.

    2. A288735E02
      Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 13 water by-pass hose from the No. 2 water by-pass pipe sub-assembly and compressor inlet elbow.
      Text in Illustration 
      *1
      No. 2 Water By-pass Hose
      *2
      No. 13 Water By-pass Hose

  1. Remove the 2 nuts, compressor inlet elbow and gasket.

  1. A288733E01
    for Type A:
    Slide the 2 clamps and remove the No. 7 water by-pass hose and No. 12 water by-pass hose from the compressor inlet elbow.
    Text in Illustration 
    *1
    No. 7 Water By-pass Hose
    *2
    No. 12 Water By-pass Hose

  1. A211835
    for Type B:
    Slide the 4 clamps and disconnect the 2 No. 1 turbo water hoses from the No. 1 turbo water pipe sub-assembly and cylinder block sub-assembly.


15. REMOVE NO. 1 TURBO INSULATOR (w/ Intercooler)

  1. A255740
    Remove the 2 bolts and No. 1 turbo insulator.


16. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR (w/ Intercooler)

  1. A255741
    Remove the bolt and No. 1 exhaust manifold heat insulator.


17. REMOVE TURBINE OUTLET ELBOW

  1. A099515E02
    w/o Intercooler:
    Remove the 2 bolts, 4 nuts, turbine outlet elbow (with turbocharger stay) and gasket.

  1. A211836
    w/ Intercooler:
    Remove the 3 nuts, turbine outlet elbow and gasket.


18. REMOVE TURBOCHARGER STAY (w/ Intercooler)

  1. A211837
    Remove the 2 bolts, nut and turbocharger stay.


19. REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A098817E02
    Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe sub-assembly and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A.


20. REMOVE TURBOCHARGER SUB-ASSEMBLY

  1. w/o Intercooler:

    1. A098783E02
      Remove the 2 bolts and manifold stay.

    2. Remove the 2 bolts, union bolt and 2 gaskets.

    3. A098784E02
      Remove the 3 nuts, turbocharger sub-assembly (with turbo oil pipe sub-assembly) and gasket.

    4. A110356
      Remove the 2 nuts, turbo oil pipe sub-assembly and gasket from the turbocharger sub-assembly.

  1. A098818E01
    w/ Intercooler:
    Remove the 3 nuts, turbocharger sub-assembly and gasket.


21. REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A288732
    Remove the 2 nuts, bolt, No. 1 turbo water pipe sub-assembly and gasket.

  1. Slide the clamp and disconnect the No. 1 turbo water hose from the No. 1 turbo water pipe sub-assembly.

← REMOVAL (Aug 2012 – Jul 2013)INSPECTION (Jun 2011 – Jul 2012) →