2014 Hilux · Service Manual ENGINE

P0105 Manifold Absolute Pressure / Barometric Pressure Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure by using its built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
A006532E04
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]). As a result the ECM controls the air-fuel ratio at the proper level under any driving conditions, and fuel control accuracy is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.
DTC No.
DTC Detection Condition
Trouble Area
P0105
P0107
P0108
Open or short in manifold absolute pressure sensor circuit for 0.8 seconds or more
(1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. Turbocharger assembly
  4. EGR valve assembly
  5. ECM

HINT:
When DTC P0105, P0107, or P0108 is detected, check the intake manifold pressure by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / MAP.


Reference:
Intake Manifold Pressure
Malfunction
Approximately 0 kPa
  1. Short in PIM circuit to ground
  2. Open in VC circuit
250 kPa (1,875 mmHg, 73.8 in.Hg) or more
  1. short in VC circuit to PIM circuit
  2. Open in PIM circuit
  3. Open in E2 circuit


WIRING DIAGRAM

A110949E10

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MAP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / MAP.

  1. Read the value.

    Standard:
    Same value as the actual atmospheric pressure.



OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


2. CHECK ECM (VC VOLTAGE)

  1. A154534E12
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC (E8-18) - E2 (E8-28)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


3. INSPECT ECM (PIM VOLTAGE)

  1. A154534E13
    Turn the ignition switch ON.

  1. Measure the voltage of the ECM connectors.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    PIM (E7-28) - E2 (E8-28)
    Applied negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg)
    0.1 to 0.7 V
    PIM (E7-28) - E2 (E8-28)
    Same as atmospheric pressure
    0.8 to 1.5 V
    PIM (E7-28) - E2 (E8-28)
    Applied positive pressure of 170 kPa (1,275 mmHg, 50.2 in.Hg)
    1.6 to 2.3 V

HINT:
Even when the output voltage from the manifold absolute pressure sensor is within the specified voltage range, there may be a problem in the sensor caused by age deterioration.



OK
REPLACE ECM (Click here)
NG


4. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A154310E06
    Disconnect the T9 manifold absolute pressure sensor connector.

  1. Disconnect the E7 and E8 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    PIM (T9-2) - PIM (E7-28)
    Below 1 Ω
    VC (T9-3) - VC (E8-18)
    Below 1 Ω
    E (T9-1) - E2 (E8-28)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    PIM (T9-2) or PIM (E7-28) - Body ground
    10 kΩ or higher
    VC (T9-3) or VC (E8-18) - Body ground
    10 kΩ or higher
    E (T9-1) or E2 (E8-28) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Check the turbocharger sub-assembly (Click here).

    OK:
    None of the inspection results show any abnormalities.



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


6. INSPECT EGR VALVE ASSEMBLY
  1. Check the EGR valve assembly (Click here).

    OK:
    None of the inspection results show any abnormalities.



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR


← P0101 Mass or Volume Air Flow Circuit Range / Performance Problem (from Aug 2014)P0105 Manifold Absolute Pressure / Barometric Pressure Circuit (+ P0107, P0108) (Aug 2012 – Jul 2013) →