2014 Hilux · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The radio and display receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

E227687E03

INSPECTION PROCEDURE


1. CHECK VEHICLE SIGNAL (DISPLAY CHECK MODE)

  1. E222021
    Enter the "Function Check/Setting I" mode and select "Vehicle Signal" (Click here).

  1. Check that the display changes between ON and OFF according to the shift lever position.

    OK:
    Shift Lever Position
    Display
    R
    ON
    Except R
    OFF

    HINT:
    This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

  1. E140414E32
    Disconnect the R21 radio and display receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    R21-2 (REV) - Body ground
    Ignition switch ON, shift lever in R
    7.5 to 14 V
    R21-2 (REV) - Body ground
    Ignition switch ON, shift lever not in R
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Automatic Transmission)
    B
    NG (for Manual Transmission)
    C



B
Go to step 3

C
Go to step 4
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

3. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the R21 radio and display receiver assembly connector.

  1. Disconnect the N1 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R21-2 (REV) - N1-1 (RL)
    Always
    Below 1 Ω
    R21-2 (REV) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for A340E)
    A
    OK (for A340F)
    B
    OK (for A750E)
    C
    OK (for A750F)
    D
    NG
    E



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

D
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

E
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the R21 radio and display receiver assembly connector.

  1. Disconnect the B1 back-up light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R21-2 (REV) - B1-1
    Always
    Below 1 Ω
    R21-2 (REV) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for R150/R151/R156)
    A
    OK (for R151F/R156F)
    B
    NG
    C



B
REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)


← Screen Flicker or Color Distortion (from Aug 2013)Reverse Signal Circuit (Aug 2012 – Jul 2013) →