2014 Hilux · Service Manual SECURITIES

Engine does not Start

Circuit diagnosis · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

If the engine does not start and no DTCs are output, there is an open or short circuit between the ECM or transponder key ECU assembly.

WIRING DIAGRAM

B289968E01

INSPECTION PROCEDURE

NOTICE:
  1. Before troubleshooting this symptom, make sure no engine immobiliser system DTCs, SFI system (for 1TR-FE, 2TR-FE, 1GR-FE) or ECD system (for 1KD-FTV, 2KD-FTV) DTCs are present. If present, troubleshoot the engine immobiliser system DTCs first.
  2. When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.


1. CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)

  1. B274402E02
    Using an oscilloscope, check the waveform.
    Measurement Condition  
    Item
    Content
    Tester Connection
    T21-13 (EFIO) - T21-16 (GND)
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON

    HINT:
    1. The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
    2. Check the waveform when the security indicator light assembly is off (the engine immobiliser system is unset). If the security indicator light assembly does not turn off (the engine immobiliser system cannot be unset), refer to the "Problem Symptoms Table (Click here)".

    OK:
    Waveform is output normally (refer to illustration).

    Text in Illustration 
    *1
    Waveform
    *a
    Component with harness connected
    (Transponder Key ECU Assembly)
    Result 
    Result
    Proceed to
    NG (stuck LOW: 1 V or less)
    A
    NG (stuck HI: 10 V)
    B
    OK
    C

HINT:
If replacing the ECM, refer to the procedures below.
  1. for 1KD-FTV (except DPF): Click here
  2. for 1KD-FTV (for DPF): Click here
  3. for 2KD-FTV (except DPF): Click here
  4. for 2KD-FTV (for DPF): Click here
  5. for 1TR-FE: Click here
  6. for 2TR-FE: Click here
  7. for 1GR-FE: Click here



B
REPLACE ECM

C
Go to step 5
A


Go to step 3

2. REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


NEXT


3. REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


4. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts normally.

    OK:
    Engine starts normally.

HINT:
If replacing the ECM, refer to the procedures below.
  1. for 1KD-FTV (except DPF): Click here
  2. for 1KD-FTV (for DPF): Click here
  3. for 2KD-FTV (except DPF): Click here
  4. for 2KD-FTV (for DPF): Click here
  5. for 1TR-FE: Click here
  6. for 2TR-FE: Click here
  7. for 1GR-FE: Click here



NG
REPLACE ECM
OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

5. REGISTER ECU COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Refer to the Service Bulletin).


NEXT


6. CHECK WHETHER ENGINE STARTS
  1. Check that the engine starts normally.

    OK:
    Engine starts normally.

HINT:
If replacing the ECM, refer to the procedures below.
  1. for 1KD-FTV (except DPF): Click here
  2. for 1KD-FTV (for DPF): Click here
  3. for 2KD-FTV (except DPF): Click here
  4. for 2KD-FTV (for DPF): Click here
  5. for 1TR-FE: Click here
  6. for 2TR-FE: Click here
  7. for 1GR-FE: Click here



NG
REPLACE ECM
OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)


← Engine does not Start (Jun 2011 – Jul 2012)Engine does not Start (from Aug 2013) →