2014 Hilux · Service Manual SECURITIES

Starter Relay Circuit

Circuit diagnosis · Vehicles built from Nov 2011

Versions by build date: Jun 2011 – Oct 2011 from Nov 2011

DESCRIPTION

When the theft deterrent system operates, the theft warning ECU assembly deactivates the ST relay so that the starter cannot crank the engine.

WIRING DIAGRAM

B276451E10

INSPECTION PROCEDURE

NOTICE:
  1. If the engine cranks but does not start, there is a problem with the SFI system*1 or ECD system*2. If this is the case, refer to SFI System*1 or ECD System*2 and perform troubleshooting.
    1. *1: for 2TR-FE
    2. *2: for 1KD-FTV, 2KD-FTV
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  3. When replacing the theft warning ECU assembly, refer to the registration procedures (Click here).


1. INSPECT ST RELAY

  1. B205010E06
    Remove the ST relay from the engine room relay block and junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage is not applied to terminals 1 and 2
    10 kΩ or higher
    Battery voltage is applied to terminals 1 and 2
    Below 1 Ω

    Text in Illustration 
    *A
    for 2TR-FE
    *B
    for 1KD-FTV, 2KD-FTV



NG
REPLACE ST RELAY
OK


2. INSPECT IGNITION SWITCH ASSEMBLY

  1. B275965E02
    Remove the ignition switch assembly.
    1. for 2TR-FE: Click here
    2. for 1KD-FTV: Click here
    3. for 2KD-FTV: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (AM2) - 7 (ST2)
    Off, ACC, ON
    10 kΩ or higher
    Start
    Below 1 Ω

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2TR-FE)
    B
    NG (for 1KD-FTV)
    C
    NG (for 2KD-FTV)
    D



B
REPLACE IGNITION SWITCH ASSEMBLY (Click here)

C
REPLACE IGNITION SWITCH ASSEMBLY (Click here)

D
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
A


3. CHECK VEHICLE TYPE
  1. Check the vehicle type.

    Result 
    Result
    Proceed to
    for Automatic Transmission
    A
    for Manual Transmission
    B



B
Go to step 5
A


4. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. B276452
    Remove the park/neutral position switch assembly.
    1. for A340E: Click here
    2. for A340F: Click here
    3. for A343E: Click here
    4. for A343F: Click here
    5. for A750E: Click here
    6. for A750F: Click here

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 - 5
    Shift lever in P or N
    Below 1 Ω
    Shift lever not in P and N
    10 kΩ or higher

    HINT:
    If replacing the park/neutral position switch assembly, refer to the procedures above.



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (ST RELAY - BATTERY)

  1. B276697E01
    Remove the ST relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2TR-FE:
    Tester Connection
    Condition
    Specified Condition
    Relay block ST relay terminal 3 - Body ground
    Always
    11 to 14 V
    for 1KD-FTV, 2KD-FTV:
    Tester Connection
    Condition
    Specified Condition
    Relay block ST relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *A
    for 2TR-FE
    *B
    for 1KD-FTV, 2KD-FTV
    *a
    Front view of wire harness connector
    (to ST Relay)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)

  1. B274165E08
    Disconnect the T36 theft warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T36-1 (E) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T36-12 (SRLY) - Body ground
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Theft Warning ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE THEFT WARNING ECU ASSEMBLY


← Starter Relay Circuit (Jun 2011 – Oct 2011)ECU Power Source Circuit (from Jun 2011) →