Home › General › MAINTENANCE › ENGINE › 2012.01–2012.04
RM1840EF _V1 General _009567 MAINTENANCE _0052052 ENGINE N

MAINTENANCE  ENGINE  GENERAL MAINTENANCE  


CAUTION / NOTICE / HINT

HINT:

Perform these procedures after the engine has cooled down.


PROCEDURE

Hide 1.INSPECT TIMING BELT

HINT:

This is for vehicles often used in excessively dusty conditions. Inspect for cracks on the timing belt or abnormal wear on the timing pulley. Then, remove sand and dust in the timing belt cover.


Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)

Hide 2.REPLACE TIMING BELT

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)

Hide 3.INSPECT TIMING BELT PULLEY

HINT:

This is for vehicles often used in excessively dusty conditions. Inspect for cracks on the timing belt or abnormal wear on the timing pulley. Then, remove sand and dust in the timing belt cover.


Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)

Hide 4.CLEAN TIMING BELT COVER (for 1KD-FTV, 2KD-FTV)

HINT:

This is for vehicles often used in excessively dusty conditions. Inspect for cracks on the timing belt or abnormal wear on the timing pulley. Then, remove sand and dust in the timing belt cover.


a.

Remove the timing belt cover.


b.

Check that the timing belt cover is not dirty.


c.

If cleaning a timing belt cover, blow compressed air to clean it.


d.

Reinstall the timing belt cover.


Hide 5.INSPECT VALVE CLEARANCE (for 1KD-FTV, 2KD-FTV)

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)

Hide 6.INSPECT DRIVE BELT

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 7.REPLACE ENGINE OIL AND OIL FILTER

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 8.INSPECT COOLING AND HEATER SYSTEM

a.

Check that the radiator, condenser and/or intercooler is not blocked with leaves, dirt or insects, and clean them if necessary. Also check the hose connection for the installation condition, corrosion, etc.


Hide 9.INSPECT ENGINE COOLANT

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 10.REPLACE ENGINE COOLANT

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 11.INSPECT EXHAUST PIPES AND MOUNTINGS

a.

Visually check the pipes, hangers and connections for severe corrosion, leaks or damage.


Hide 12.REPLACE SPARK PLUGS (for 2TR-FE, 2TR-FBE)

Type See procedure
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 13.INSPECT BATTERY

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 14.INSPECT WATER SEDIMENT ACCUMULATOR

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)

Hide 15.REPLACE FUEL SENDER GAUGE (for 2TR-FBE, Fuel Main Tank)

Hide 16.CLEAN FUEL PUMP SUCTION FILTER (for 2TR-FBE, Fuel Main Tank)

a.
D104369
1.823,0.354 2.042,0.521 0.219,0.167 10 false *b 1.823,2.104 2.052,2.271 0.229,0.167 10 false *b 0.51,1 0.729,1.167 0.219,0.167 10 false *a
*a CORRECT
*b INCORRECT


Remove the fuel pump.


b.

While keeping the air gun parallel to the face of the suction filter, blow compressed air to clean the suction filter.

NOTICE:

Do not blow compressed air directly onto the face of the suction filter, as this will only make clogs worse.



Hide 17.REPLACE FUEL FILTER (for 2TR-FE, 2TR-FBE)

Type See procedure
2TR-FE (Click here)
2TR-FBE (for Fuel Main Tank) (Click here)
2TR-FBE (for Fuel Sub Tank) No. 2 fuel tube sub-assembly (Fuel filter assembly)
(Click here)

Hide 18.INSPECT AIR FLOW METER (for 1KD-FTV (w/ EGR Cooler), 2KD-FTV (w/ EGR Cooler))

a.

Blow air to the sensor intermittently for approximately 30 seconds.


Hide 19.INSPECT AIR CLEANER FILTER

a.

Remove the air cleaner filter.


b.

Visually check that the air cleaner filter is not excessively damaged or oily. If necessary, replace the air cleaner filter with a new one.


c.

If cleaning an air cleaner filter element, blow compressed air to clean it.


d.

Reinstall the air cleaner filter.


Hide 20.INSPECT FUEL TANK CAP GASKET

Type See procedure
1KD-FTV (Click here)
2KD-FTV (Click here)
2TR-FE (Click here)
2TR-FBE (Click here)

Hide 21.INSPECT FUEL LINES, FUEL LINE CONNECTIONS, FUEL TANK VAPOR VENT SYSTEM HOSES AND FUEL TANK BAND

a.

Visually check the fuel lines and hoses for cracks, leakage, loose connections and deformation. Also, visually check the tank band for looseness.


Hide 22.INSPECT CHARCOAL CANISTER (for 2TR-FE, 2TR-FBE)

Type See procedure
2TR-FE (Click here)
2TR-FBE (Click here)