Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052066 ECD SYSTEM(w/o EGR Cooler) J

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  Lack of Power or Hesitation  


DESCRIPTION

Malfunction Condition Main Trouble Area Related Trouble Area
·

Lack of power caused by abnormal fuel injection volume (fuel supply pump malfunction, injector assembly malfunction, etc.)

·

Lack of power caused by intake air volume shortage (turbocharger malfunction, or front exhaust pipe or exhaust manifold converter blocked)


(a) Injector assembly malfunctions
·

Injector sliding malfunction

·

Injector stuck closed

·

Injector stuck open

·

Deposits in injector

·

Injector circuit malfunction


(b) Abnormal common rail pressure
·

Fuel supply pump


(c) Abnormal intake air volume
·

Intake air system leakage or clogged

·

Turbocharger

·

Front exhaust pipe blockage

·

Exhaust manifold converter blockage

·

EGR valve does not close

·

Throttle valve does not open


·

Pressure discharge valve (P1271 stored simultaneously)

·

Intake air system blockage

·

EGR system

·

Fuel filter is clogged

·

Throttle valve

·

Mass air flow meter

·

Compression pressure

·

Injector compensation code

·

Fuel leak

·

Glow plug

·

Fuel pressure sensor

·

Manifold absolute pressure sensor

·

Vacuum hose connection for manifold absolute pressure sensor

·

Injector driver (P0200 stored simultaneously)

·

Vehicle modifications

·

Clutch disc wear

·

Low quality fuel

·

Frozen fuel

·

ECM



HINT:
·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.

·

This troubleshooting procedure checks for the cause of an obvious lack of engine power while the vehicle is being driven (such as the maximum speed being extremely low).



Faults and Symptoms of Common Rail Diesel Components


a.

Engine Control

Mass Air Flow Meter
Main fault Decrease in performance (foreign matter is stuck)
Symptoms Lack of power, black smoke
Data List MAF
HINT:

The maximum fuel injection volume is controlled according to the output from the mass air flow meter.



Intake System
Symptom and Corresponding Main Fault
·

Lack of power (no black smoke) due to air filter blockage or crushed or leaking air duct

·

Black smoke (no lack of power) due to leakage between the turbo and intake manifold


Data List
·

MAP

·

MAF



Turbocharger System
Main fault
·

Air leak in the turbocharged air passage

·

Turbocharger (turbine, bearing)


Symptoms Lack of power (when vehicle is starting, under heavy load)
(Black smoke is not emitted when racing while vehicle is stopped)
Data List MAP
·

With the ignition switch ON or during idling, MAP = atmospheric pressure (standard atmospheric pressure = 101 kPa). When the engine speed is about 1500 rpm or more, the turbocharger starts to take effect and MAP becomes higher than atmospheric pressure.

·

Atmospheric pressure decreases by 1 kPa each time elevation increases by 100 m, and is also affected by the current weather conditions.



Exhaust System
Main fault Blockage
Symptoms Lack of power (high engine speed, under heavy load)

Glow System
Main fault Open circuit, glow plug relay fault
Symptoms Difficult to start, rough idle, knocking, white smoke (when cold)
Data List Check the glow plug indicator light
Diagnostic Point Measure the resistance of the glow plug

Engine - 1
Main fault Damaged, seized up
Symptoms Cannot crank, crank speed is low, strange noise

Engine - 2
Main fault Loss of compression
Symptoms Rough idle (lack of power always)
Data List Engine Speed of Cyl#
·

When cranking during the "Check the Cylinder Compression" Active Test, if there is a high speed cylinder, approx. 100 rpm more than the other cylinders, that cylinder may lose compression.


Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder.




b.

Diesel Injection

Fuel Supply Pump
Main fault -
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure, Target Pump SCV Current
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.

·

If Target Pump SCV Current is 3000 mA or higher, the suction control valve may be stuck.


HINT:
·

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.

·

When Target Pump SCV Current is 3000 mA or higher, the suction control valve has a tendency to become stuck.



Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Fuel Filter
Main fault Blockage
Symptoms Difficult to start, engine stalling, rough idle, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).

·

If the fuel pressure is 20000 kPa below the target pressure, then a lack of power will be felt.

·

If the fuel pressure is below 25000 kPa, then idling will be rough.


HINT:

The fuel pressure changes at engine start, but is approx. 25000 kPa at engine start after the engine is warmed up.


Diagnostic Trouble Code Even if Fuel Press is below Target Common Rail Pressure, a DTC will not be stored.

Injector Assembly
Main fault Blockage
Symptoms Rough idle, lack of power, black smoke, white smoke, knocking
Data List Injection Feedback Val
·

When an Injector Feedback Val is more than 3 mm3/st, there may be a malfunction in the corresponding cylinder. This value can be read after idling for 1 minute.



Injector Driver
Main fault Circuit fault: The injector assembly does not open.
Symptoms Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking
Data List Same as injector assembly
Diagnostic Trouble Code When the injector driver has a fault, some DTCs may be stored.

Fuel Pressure Sensor
Main fault Open circuit, decrease in performance (foreign matter is stuck)
Symptoms Difficult to start, rough idle, engine stall, lack of power
Data List Fuel Press, Target Common Rail Pressure
·

Fuel Press is within 5000 kPa of Target Common Rail Pressure during idling with the engine warmed up (engine coolant temperature is higher than 70°C (158°F)).


Diagnostic Code When the fuel pressure sensor has a fault, some DTCs may be stored.

Irregular Fuel
Main fault -
Symptoms Difficult to start, rough idle (especially when cold)


c.

Diesel EGR

EGR System
Main fault
·

Does not move smoothly

·

Does not close fully


Symptoms
·

Rough Idle

·

EGR valve stuck closed: A loud turbocharger sound.

·

EGR valve stuck open: Difficult to start (does not stall), black smoke, white smoke (when engine is cold), lack of power, jerking (If there is an excess in the quantity of EGR and there is a heavy load, when the vehicle starts moving, a lack of power will be felt. Also, when racing the engine, there will be some black smoke).


Data List Actual EGR Valve Pos., Target EGR Position
·

Generally, Actual EGR Valve Pos. = Target EGR Position +/-5% (fully closed: 0%, fully open: 100%).

·

Using the EGR valve Active Test, check whether Actual EGR Valve Pos. follows Target EGR Position (the engine coolant temperature and intake air temperature should be considered when a malfunction occurs).

·

EGR valve is fully closed when the ignition switch is ON (engine stopped).

·

EGR valve opens to the halfway point at idling after the engine is warmed up.

·

When the EGR valve does not close, MAF (Mass Air Flow) decreases when the vehicle is accelerated at full throttle.


EGR Close Lrn. Val., EGR Close Lrn. Status
·

When leaving the vehicle idling, when EGR Close Lrn. Status is OK, the normal range of EGR Close Lrn. Val. is 0 to 1 V.

·

In cases when EGR Close Lrn. Status. is NG or EGR Close Lrn. Val. is out of the normal range (0 to 1 V), it is possible that the EGR valve cannot completely close.




d.

Diesel Throttle

Diesel Throttle System
Main fault Stuck, does not move smoothly
Symptoms
·

Stuck closed: Lack of power, difficult to start, rough idle, engine stall, black smoke. These may occur when stuck almost fully closed.

·

Stuck open: Turbocharger sound increases. When the engine is stopped, engine vibrations may occur.


Data List
·

Actual Throttle Position (fully closed: 100%, fully open: 0%)

·

When the ignition switch is ON (engine stopped), the diesel throttle is fully open. When idling, the diesel throttle is at the halfway point. When the ignition switch is turned from ON to off, the throttle is fully closed temporarily.





Data List Related to Lack of Power


·

Engine Speed

·

MAP

·

MAF

·

Intake Air

·

Coolant Temp

·

Target Common Rail Pressure

·

Fuel Press

·

Target Pump SCV Current

·

Injection Feedback Val #1 (to #4)

·

Injection Volume

·

Actual Throttle Position

·

Target EGR Position

·

Actual EGR Valve Pos.



CAUTION / NOTICE / HINT

Explanation of Symptom


Lack of Power The power of the diesel engine is determined by the quantity of injected fuel and the quantity of intake air.
The quantity of injected fuel is determined by the fuel pressure and the amount of time the injector assembly is open. Basically, the fuel pressure is controlled so that it reaches the target fuel pressure. The throttle valve does not restrict air flow volume, so the manifold absolute pressure is almost the same as atmospheric pressure when idling. At more than approximately 1500 rpm, the turbo starts to operate causing the manifold absolute pressure to become higher than atmospheric pressure.


NOTICE:
·

After replacing the fuel supply pump, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION).



PROCEDURE

1.READ OUTPUT DTC (RELATING TO ENGINE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the pending DTCs.

Result:
Result Proceed to
No DTCs are output A
Engine related DTCs are output B




A

2.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 2)

B

2.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (PROCEDURE 2)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Lack of power.


d.
A241174
2.042,2.719 2.427,2.24 2.427,2.24 2.646,2.24 true 2.677,2.146 2.896,2.354 0.219,0.208 10 false *1
*1 Snapshot Button


With no load after the engine is warmed up, take a snapshot when idling and at 4000 rpm.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.

·

The shift lever should be in neutral and the A/C switch and all accessory switches should be off.




Result:
Proceed to
NEXT



NEXT

3.TAKE SNAPSHOT DURING LACK OF POWER (PROCEDURE 3)
3.TAKE SNAPSHOT DURING LACK OF POWER (PROCEDURE 3)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.


d.
A241174
2.042,2.719 2.427,2.24 2.427,2.24 2.646,2.24 true 2.677,2.146 2.948,2.323 0.271,0.177 10 false *1
*1 Snapshot Button


Take a snapshot of the Data List items with the intelligent tester during lack of power.

HINT:
·

A snapshot can be used to compare vehicle data from the time of the malfunction to normal data and is very useful for troubleshooting.

·

Graphs can be displayed by transferring the stored snapshot data from the tester to a PC. Intelligent Viewer must be installed on the PC.

·

Move the shift lever to 2nd gear and accelerate the vehicle with the accelerator pedal fully depressed so that the engine speed is around 3000 rpm (obey all laws and regulations, and pay attention to traffic conditions while driving the vehicle). Then, check the Data List with the engine warmed up and idling (the shift lever should be in neutral and the A/C switch and all accessory switches should be off).




e.

Check for a lack of power during the driving test.


Result:
Result Proceed to
Apparent lack of power is present A
Apparent lack of power is not present B



A

4.CHECK SNAPSHOT (MAP)

B

9.COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE
4.CHECK SNAPSHOT (MAP)
a.

Check MAP in the snapshot taken in procedure 2 when the engine was running at 4000 rpm with no load.

Result:
Result Proceed to
Except below*1 A
MAP is below 90 kPa*2 B
MAP is 210 kPa or higher*3 C


HINT:

The above values were measured under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.

*1: There may be a problem in the intake system or a problem with the EGR valve (valve stuck open or valve does not close).

*2: There may be a problem in the turbocharger system.

*3: There may be a problem in the turbocharger (waste gate valve) or fuel system.




A

5.CHECK SNAPSHOT (FUEL PRESS, TARGET COMMON RAIL PRESSURE AND MAP)

B

30.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE)

C

6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
5.CHECK SNAPSHOT (FUEL PRESS, TARGET COMMON RAIL PRESSURE AND MAP)
a.

Check Fuel Press, Target Common Rail Pressure and MAP in the snapshot taken in procedure 3 when the vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear and the engine speed around 3000 rpm.

Result:
Result Proceed to
MAP is 230 kPa or higher at an engine speed of 3000 rpm A
Difference between Fuel Press and Target Common Rail Pressure is 20000 kPa or more B
Except above C


HINT:
·

The above values are applicable under standard atmospheric pressure. The values are influenced by elevation, weather conditions, etc.

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.

·

The engine speed must be 1500 rpm or less before performing the inspection in which the accelerator pedal is fully depressed and the engine is accelerated to a speed of 3000 rpm.

·

If "Fuel pressure" follows "Target common rail pressure" during idling or low speed driving but is insufficient during acceleration or high speed driving, the fuel filter may be clogged.





A

6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

B

11.INSPECT CLOGGED FUEL PIPE

C

20.CHECK INTAKE SYSTEM
6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-2 (PIM) - C23-28 (PIM) Always Below 1 Ω
C20-3 (VC) - C22-18 (VC) Always Below 1 Ω
C20-1 (E) - C22-28 (E2) Always Below 1 Ω
C20-2 (PIM) or C23-28 (PIM) - Body ground Always 10 kΩ or higher
C20-3 (VC) or- C22-18 (VC) - Body ground Always 10 kΩ or higher
C20-1 (E) or C22-28 (E2) - Body ground Always 10 kΩ or higher



HINT:
·

Make sure that there is no evidence of any wire harnesses being crushed and that there are no wires that are about to snap.

·

Make sure that no terminals are worn down and that there are no bad connections.

·

Make sure there are no shorts between wires in areas where the wires bend or where a clamp might have slid along the wire harness.

·

Make sure there are no shorts to body ground in areas where wire harnesses are attached to metal parts.



Result:
Proceed to
OK
NG



OK

7.CHECK OR REPLACE TURBOCHARGER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK OR REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Disconnect the actuator hose from the compressor housing.


b.

Close the compressor housing side tube with a hose clip or equivalent.


c.
A148172

Using SST, apply pressure to the actuator to open the waste gate valve.

Valve opening pressure:

Specified pressure* (See table below)


NOTICE:

Never apply more than the predetermined maximum pressure* to the actuator.


HINT:

*: Valve opening pressure and predetermined maximum pressure above differ according to the turbocharger. For the specifications, see the table below.


Specifications:
Engine Type Turbocharger Sub-assembly
(Part No.)
Valve Opening Pressure
(kPa: Gauge Pressure)
Maximum Pressure
(kPa: Gauge Pressure)
Reference:
Rod Stroke
(mm)
2KD-FTV 17201-0L030
17201-30120
114 136 0.98 to 1.91
17201-0L050 123 147.8 0.89 to 1.74


SST
09992-00242  

d.

Check that the actuator rod moves and that the waste gate valve opens.


HINT:

If the waste gate valve does not open, replace the turbocharger sub-assembly.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

9.COMPARE WITH SIMILAR VEHICLE WITH SAME ENGINE
a.

Confirm the situation in which the lack of power was experienced by the customer again, and compare the driving feeling under the same conditions using a similar vehicle with the same engine while collecting data with the intelligent tester.

HINT:

Confirm the state of the following conditions when the lack of power was experienced.


·

Accelerator pedal position (vehicle load)

·

Vehicle speed

·

Engine coolant temperature

·

Ambient temperature

·

Driving conditions before the lack of power occurred

·

Climate

·

Road and traffic conditions

·

When (what day) the problem was noticed

·

Whether the problem occurs suddenly or gradually

·

How often the problem occurs

·

Why the customer felt there is a lack of power (e.g. the customer compared their vehicle with another vehicle, somebody told the customer that their vehicle has a lack of power, etc.)

·

Level of lack of power (slight or drastic)


Result:
Result Proceed to
Significant difference is found A
Significant difference is not found B




A

4.CHECK SNAPSHOT (MAP)

B

10.EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER
10.EXPLAIN THE INVESTIGATION RESULT TO CUSTOMER
a.

Vehicle performance is normal. There is no problem at this point in time. However, if the problem reoccurs, ask the customer to explain in detail the situation in which the problem occurred. The best course may be to have the customer ride in another vehicle with the same specifications to understand that there is no problem with the customer's vehicle.


Result:
Proceed to
NEXT



NEXT

END

11.INSPECT CLOGGED FUEL PIPE
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Diesel Injection.


d.

With no load after the engine is warmed up, take a snapshot when idling and vehicle was accelerating with the accelerator pedal fully depressed in 2nd gear.


e.

Check the Target Common Rail Pressure and Fuel Press value.

A261221
0.177,1.708 1.167,2.167 0.99,0.458 10 false Target Common Rail Pressure 3.854,2.125 5.052,2.354 1.198,0.229 10 false Normal Fuel Press 3.75,0.438 5.24,0.677 1.49,0.24 10 false Abnormal Fuel Press*1 0.115,0.115 1.823,0.354 1.708,0.24 10 false Fuel Pressure During Idling 1.115,2.406 3.594,2.917 2.479,0.51 10 false Pressure varies periodically with a period of approximately 2 seconds or more 5.906,1.104 7.01,1.479 1.104,0.375 10 false Normal Condition: +/- 5000 kPa 5.906,1.448 7.042,1.958 1.135,0.51 10 false (Idling after Engine Warmed Up)

Result:
Result Proceed to
While idling the vehicle, "Fuel Press" deviates from the normal range and varies periodically with a period of approximately 2 seconds or more*1 A
"Fuel Press" is normal while idling the vehicle, but "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear*2
Except above B


NOTICE:
·

*1: The cause may be a squashed or blocked fuel pipe or hose.

·

*2: The cause may be a clogged fuel filter.





A

12.REPAIR OR REPLACE CLOGGED FUEL LINE

B

16.REPLACE FUEL SUPPLY PUMP
12.REPAIR OR REPLACE CLOGGED FUEL LINE
a.

Repair or replace the clogged (including frozen fuel) fuel pipe.


b.

Replace the fuel filter element sub-assembly.

HINT:

If "Fuel Press" does not follow "Target Common Rail Pressure" when the accelerator pedal is fully depressed in 2nd gear, replace the fuel filter element sub-assembly.



Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
13.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

14.PERFORM FUEL SUPPLY PUMP INITIALIZATION
14.PERFORM FUEL SUPPLY PUMP INITIALIZATION

Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 416,54

d.
A241174
2.042,2.719 2.427,2.24 2.427,2.24 2.646,2.24 true 2.677,2.146 2.885,2.354 0.208,0.208 10 false *1
*1 Snapshot Button


Take a snapshot with the intelligent tester during the Active Test.

HINT:

Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.



e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.417,2.656 5.021,2.479 5.021,2.479 5.083,2.479 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.271 3.938,4.188 3.938,4.188 4.073,4.188 false 0.083,1.438 1.448,1.677 1.365,0.24 10 false Active Test Operation 0.167,0.594 1.448,0.844 1.281,0.25 10 false Engine Speed (rpm) 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Pressure 3.646,2.021 5,2.25 1.354,0.229 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.802,2.865 0.677,0.438 10 false Less than 10000 kPa 3,4.271 3.688,4.438 0.688,0.167 10 false 2 seconds 5.125,2.385 6.031,2.885 0.906,0.5 10 false Abnormal Fuel Pressure 2.448,1.125 3.125,1.323 0.677,0.198 10 false Test Start 4.177,1.125 4.844,1.323 0.667,0.198 10 false Test Stop 5.625,1.125 6.302,1.323 0.677,0.198 10 false Test Start 2.208,1.823 2.979,2.24 0.771,0.417 10 false Normal Fuel Pressure 1.646,0.313 2.021,0.479 0.375,0.167 10 false 2000 1.885,0.854 2.052,1.021 0.167,0.167 10 false 0 1.75,1.323 2.073,1.49 0.323,0.167 10 false ON 1.698,1.583 2.021,1.75 0.323,0.167 10 false OFF 4.146,4.115 5.76,4.479 1.615,0.365 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.




Result:
Proceed to
OK
NG



OK

END

NG

17.REPLACE COMMON RAIL ASSEMBLY
16.REPLACE FUEL SUPPLY PUMP

Result:
Proceed to
NEXT



NEXT

13.BLEED AIR FROM FUEL SYSTEM
17.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL SUPPLY PUMP(w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.BLEED AIR FROM FUEL SYSTEM
18.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
50004 61 90 416,54

d.
A241174
2.042,2.75 2.427,2.271 2.427,2.271 2.646,2.271 true 2.677,2.167 2.917,2.385 0.24,0.219 10 false *1
*1 Snapshot Button


Take a snapshot with the intelligent tester during the Active Test.

HINT:

Detailed graphs can be displayed by transferring the stored snapshot from the tester to a PC (personal computer) with Intelligent Viewer installed.



e.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.417,2.656 5.021,2.479 5.021,2.479 5.083,2.479 true 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.271 3.938,4.188 3.938,4.188 4.073,4.188 false 0.083,1.427 1.448,1.667 1.365,0.24 10 false Active Test Operation 0.167,0.594 1.448,0.844 1.281,0.25 10 false Engine Speed (rpm) 0.542,3.271 1.448,3.51 0.906,0.24 10 false Fuel Pressure 3.646,2.021 5,2.25 1.354,0.229 10 false Target Fuel Pressure 6.469,4.135 6.865,4.313 0.396,0.177 10 false Time 2.125,2.427 2.792,2.813 0.667,0.385 10 false Less than 10000 kPa 3,4.271 3.688,4.438 0.688,0.167 10 false 2 seconds 5.125,2.385 6.031,2.76 0.906,0.375 10 false Abnormal Fuel Pressure 2.448,1.125 3.125,1.323 0.677,0.198 10 false Test Start 4.177,1.125 4.844,1.323 0.667,0.198 10 false Test Stop 5.625,1.125 6.302,1.323 0.677,0.198 10 false Test Start 2.208,1.823 2.969,2.219 0.76,0.396 10 false Normal Fuel Pressure 1.646,0.313 2.021,0.479 0.375,0.167 10 false 2000 1.885,0.854 2.052,1.021 0.167,0.167 10 false 0 1.75,1.323 2.073,1.49 0.323,0.167 10 false ON 1.698,1.583 2.021,1.75 0.323,0.167 10 false OFF 4.146,4.115 5.802,4.448 1.656,0.333 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.




Result:
Proceed to
NEXT



NEXT

END

20.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

When checking whether the intake system is clogged (which causes a low MAP), perform the following checks:

·

Check whether the air cleaner is clogged.

·

Check whether an intake hose is clogged.

·

Check whether the diesel throttle valve is stuck in the closed position.


·

Check for any modifications in the intake system made by the user.




OK:

No leaks or blockages in the intake system.


Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

NG

26.REPAIR OR REPLACE AIR INTAKE SYSTEM
21.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-2 (PIM) - C23-28 (PIM) Always Below 1 Ω
C20-3 (VC) - C22-18 (VC) Always Below 1 Ω
C20-1 (E) - C22-28 (E2) Always Below 1 Ω
C20-2 (PIM) or C23-28 (PIM) - Body ground Always 10 kΩ or higher
C20-3 (VC) or- C22-18 (VC) - Body ground Always 10 kΩ or higher
C20-1 (E) or C22-28 (E2) - Body ground Always 10 kΩ or higher


HINT:
·

Make sure that there is no evidence of any wire harnesses being crushed and that there are no wires that are about to snap.

·

Make sure that no terminals are worn down and that there are no bad connections.

·

Make sure there are no shorts between wires in areas where the wires bend or where a clamp might have slid along the wire harness.

·

Make sure there are no shorts to body ground in areas where wire harnesses are attached to metal parts.




Result:
Proceed to
OK
NG



OK

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE EGR VALVE CLOSE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.


c.

Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

f.

Read the MAF value displayed on the tester while the engine is idling.


g.

Enter the following menus: Powertrain / Engine and ECT / Activate the EGR Valve Close.

Powertrain > Engine > Active Test
Tester Display
Activate the EGR Valve Close
50004 61 183

h.

Read the MAF value when the EGR valve is closed using the Active Test function.

HINT:
·

If idling continues for 15 minutes or more, the EGR valve target opening angle becomes 0% (EGR valve fully closed). As this makes diagnosis impossible, it becomes necessary to drive the vehicle or restart the engine.

·

Before performing the diagnosis, confirm that the EGR valve target opening angle is not 0%.



Result:
Active Test Result Proceed to
Activate the EGR Valve Close:
Off (Open) to On (Closed)
MAF value does not change A
MAF value changes B


NOTICE:

As the measured values may differ from those shown below due to factors such as differences in measuring environments and changes in vehicle condition due to aging, do not use these values to determine whether the vehicle is malfunctioning or not.


HINT:

The problem may be a temporary one, due to the entry of deposits or foreign matter. Check that there are no deposits or foreign matter in the electric vacuum regulating valve assembly or mass air flow meter.


Reference:
EGR Valve Condition (Opening) Measuring Condition MAF (Reference)
Open (55%)
·

Atmosphere pressure: 101 kPa

·

Intake air temperature: 30°C (86°F)

·

Engine coolant temperature: 88°C (190°F)


3.0 to 9.0 gm/s
Closed (0%) 13 to 20 gm/s




A

23.READ VALUE USING INTELLIGENT TESTER (MAF)

B

34.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
23.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

d.

Read the value.

Standard:
Tester Display Condition Specified Condition
MAF Engine not running Less than 0.35 gm/s



Result:
Proceed to
OK
NG



OK

24.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)

NG

27.REPLACE MASS AIR FLOW METER
24.REMOVE DEPOSIT (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Remove the electric EGR control valve assembly.


b.

Visually check the electric EGR control valve assembly for deposits. If there are deposits, clean the electric EGR control valve assembly.

HINT:
·

If the EGR valve does not open properly or is stuck closed, the amount of intake air increases and combustion sounds and engine vibration may increase.

·

If the EGR valve does not operate due to clogging or disconnection of the vacuum hose, repair the hose.

·

If the EGR valve does not close properly or is stuck open, EGR becomes excessive and combustion becomes unstable. Also, there may be a lack of power. In this case, clean the electric EGR control valve assembly.

·

When cleaning the electric vacuum regulating valve assembly, use a piece of cloth soaked with non-residue solvent. Spraying the solvent directly onto these parts or soaking the parts in solvent may damage the parts.




c.

Reinstall the electric EGR control valve assembly.


Result:
Proceed to
NEXT



NEXT

25.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
25.INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Inspect the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EGR VALVE(w/o DPF)>INSPECTION


Result:
Proceed to
OK
NG



OK

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

28.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
26.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
27.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>MASS AIR FLOW METER(w/o DPF)>REMOVAL

HINT:
·

If foreign matter is stuck inside the mass air flow meter, the output characteristics of the mass air flow meter may change, resulting in a malfunction.

·

Before replacing the mass air flow meter, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.




Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
28.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EGR VALVE(w/o DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
29.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
OK
NG



OK

END

NG

34.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
30.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERIC PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

Powertrain > Engine > Data List
Tester Display
Atmosphere Pressure
MAP
50003 61 64,314

d.

Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).

Standard:

Difference between MAP and Atmosphere Pressure is less than 8 kPa.


HINT:
·

If MAP and Atmosphere Pressure have the same value, both are normal. If there is a difference of 8 kPa or more, compare the values to the atmospheric pressure for that day. The sensor whose deviation is the greatest is malfunctioning.

·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather.




Result:
Result Proceed to
MAP and Atmosphere Pressure have same value A
MAP is different from actual atmospheric pressure B
Atmosphere Pressure is different from actual atmospheric pressure C



A

31.CHECK AIR INTAKE SYSTEM

B

38.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

C

49.REPLACE ECM
31.CHECK AIR INTAKE SYSTEM
a.

Check for air leaks and blockages between the air cleaner case and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Inspect the air intake system, especially hoses and pipes between the air cleaner and turbocharger.

·

Check for abnormal disconnections, pipe and hose squashing, and any damage in the intake system.

·

Using your hand, check whether the pipes and hoses in the intake system are securely connected.

·

By applying soapy water and revving up the engine, air leaks from the intake system can be checked by checking for bubbles.

·

Check for any modifications in the intake system made by the user.



OK:

No leakage or blockage.



Result:
Proceed to
OK
NG



OK

32.CHECK TURBOCHARGER SUB-ASSEMBLY

NG

39.REPAIR OR REPLACE AIR INTAKE SYSTEM
32.CHECK TURBOCHARGER SUB-ASSEMBLY

b.

Inspect the turbocharger housing.

i.

Visually check that there are no scratches or chipped areas inside the turbine housing or compressor housing.


ii.

Visually check that there are no scratches or chipped areas on the blades of the impeller or turbine wheel.



Result:
Proceed to
OK
NG



OK

33.CHECK FOR INTERMITTENT PROBLEMS

NG

40.REPLACE TURBOCHARGER SUB-ASSEMBLY
33.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
34.CHECK FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
a.

Remove the front exhaust pipe assembly.


b.

Visually check for catalyst clogging or carbon deposits adhering to the inner wall of the exhaust pipe upstream of the catalyst.

OK:

Less than 10% of the cells are clogged.



c.

Reinstall the front exhaust pipe assembly.


Result:
Proceed to
OK
NG



OK

35.INSPECT TURBOCHARGER SUB-ASSEMBLY

NG

42.REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
35.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Disconnect the actuator hose from the compressor housing.


b.

Close the compressor housing side tube with a hose clip or equivalent.


c.
A148172

Using SST, apply pressure to the actuator to open the waste gate valve.

Valve opening pressure:

Specified pressure* (See table below)


NOTICE:

Never apply more than the predetermined maximum pressure* to the actuator.


HINT:

*: Valve opening pressure and predetermined maximum pressure above differ according to the turbocharger. For the specifications, see the table below.


Specifications:
Engine Type Turbocharger Sub-assembly
(Part No.)
Valve Opening Pressure
(kPa: Gauge Pressure)
Maximum Pressure
(kPa: Gauge Pressure)
Reference:
Rod Stroke
(mm)
2KD-FTV 17201-0L030
17201-30120
114 136 0.98 to 1.91
17201-0L050 123 147.8 0.89 to 1.74


SST
09992-00242  

d.

Check that the actuator rod moves and that the waste gate valve opens.


HINT:

If the waste gate valve does not open, replace the turbocharger sub-assembly.



f.

Inspect the turbocharger housing.

i.

Visually check that there are no scratches or chipped areas inside the turbine housing or compressor housing.


ii.

Visually check that there are no scratches or chipped areas on the blades of the impeller or turbine wheel.



Result:
Proceed to
OK
NG



OK

36.CHECK FOR INTERMITTENT PROBLEMS

NG

43.REPLACE TURBOCHARGER SUB-ASSEMBLY
36.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
OK
NG



OK

END

NG

44.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
38.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Replace the manifold absolute pressure sensor.


Result:
Proceed to
NEXT



NEXT

41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
39.REPAIR OR REPLACE AIR INTAKE SYSTEM
a.

Repair or replace the malfunctioning part in the air intake system.


Result:
Proceed to
NEXT



NEXT

41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
40.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

42.REPLACE FRONT EXHAUST PIPE ASSEMBLY (CATALYTIC CONVERTER)
a.

Replace the front exhaust pipe assembly.


Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
43.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

37.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
44.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

45.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
45.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS
a.

Replace the injector assemblies.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR(w/o DPF)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

46.BLEED AIR FROM FUEL SYSTEM
46.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

47.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
47.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

48.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
48.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
Result:
Proceed to
NEXT



NEXT

END

49.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

41.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED