Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P1605  Rough Idling  


DESCRIPTION

P1605

After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.

Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1605 Rough Idling After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less without the ignition switch being operated (1 trip detection logic).
·

Air leak in intake system

·

Purge VSV

·

Brake booster

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Thermostat

·

Power supply circuit (purge VSV, air fuel ratio sensor, fuel injector assembly, ignition coil assembly)

·

Fuel pump

·

Fuel pump control circuit

·

Fuel line

·

PCV valve and hose

·

Camshaft timing oil control valve

·

Knock sensor

·

Ignition system

·

Air conditioning system

·

Power steering system

·

Electrical load signal system

·

Charging system

·

ECM

·

Wire harness or connector

·

Engine immobiliser system


- DTC stored

CAUTION / NOTICE / HINT

HINT:
·

In contrast to normal malfunction diagnosis for components, circuits and systems, DTC P1605 is used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.

As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.

·

If any other DTCs are output, perform troubleshooting for those DTCs first.

·

Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.

Symptom Suspected Area
Engine vibration occurs and engine stops Air-fuel ratio abnormal
Engine stops with no engine vibration Ignition system, injection stoppage, high load from external parts
Engine can be started with accelerator pedal depressed Insufficient air volume
Rough idling after engine started Air-fuel ratio abnormal, abnormal combustion

·

Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.

·

When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA).

·

When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.

·

Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.

·

Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.

·

When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.



Inspection flow:

Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.


P1605:

A226064
0.5,0.563 0.667,0.74 0.167,0.177 10 false 1: 0.5,0.771 1.646,1.375 1.146,0.604 10 false Did the engine speed decrease slowly or rapidly? 2.823,0.563 2.99,0.74 0.167,0.177 10 false 2: 2.823,0.76 3.969,1.323 1.146,0.563 10 false Was the air-fuel ratio abnormal or normal? 5.688,0.76 6.635,0.927 0.948,0.167 10 false Intake air leak 5.552,1.771 6.792,1.938 1.24,0.167 10 false Sensor malfunction 5.521,2.76 6.802,2.958 1.281,0.198 10 false Fuel supply problem 4.031,2.104 4.74,2.427 0.708,0.323 10 false Air volume insufficient 3.927,3.094 4.854,3.427 0.927,0.333 10 false Ignition timing incorrect 1.583,2.75 2.677,3.104 1.094,0.354 10 false Injection and ignition stoppage 1.667,3.75 2.594,4.104 0.927,0.354 10 false Load from external parts 1.906,0.875 2.615,1.271 0.708,0.396 10 false Decreased Slowly 0.271,1.896 0.99,2.25 0.719,0.354 10 false Decreased Rapidly 4.302,0.896 4.948,1.063 0.646,0.167 10 false Abnormal 2.771,1.885 3.292,2.052 0.521,0.167 10 false Normal

1:
·

If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.

·

If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.


2:
·

If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.

·

If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.


P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).

Engine Speed Suspected Area Primary Parts to Inspect Procedure
Slowly decreases and engine stalls Ignition system abnormal Igniter abnormal
·

Power supply circuit

·

Ignition coil assemblies

·

Spark plug


10, 33, 52
Air-fuel ratio abnormal Air suction
·

Intake system connections

·

Purge VSV system

·

Brake booster


5 to 9
Sensor malfunction (value from sensor too lean)
·

Mass air flow meter

·

Engine coolant temperature sensor

·

Air fuel ratio sensor system

·

Thermostat


11 to 23
Sensor malfunction (value from sensor too rich) 34 to 43
46 to 48
Fuel supply problem
·

Fuel pump control circuit

·

Purge VSV system

·

Fuel line

·

ECM


24 to 32
44 to 45
49 to 51
Intake air volume insufficient Problem with air passage
·

Intake system connections

·

Mass air flow meter

·

Brake booster

·

PCV valve and hose

·

Purge VSV system


53 to 55
Excessive valve overlap
·

Camshaft timing oil control valve


57 to 59
Ignition timing incorrect Does not operate as expected
·

Knock sensor

·

Engine coolant temperature sensor

·

Mass air flow meter


60 to 65
Rapidly decreases and engine stalls* Ignition and injection stops (electrical system malfunction) Power temporarily cut
·

Power supply circuit (fuel injector assembly, ignition coil assembly)


66, 67
External part malfunctioning Increase in load
·

Air conditioning system

·

Electrical load signal system

·

Power steering system


68, 69

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DTC CHECK / CLEAR

Result:
Result Proceed to
Only DTC P1605 is output A
DTCs other than P1605 are output B


HINT:

If any DTCs other than P1603 or P1605 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA

B

2.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

OK:

Immobiliser Fuel Cut is OFF.


Result:
Result Proceed to
Abnormal A
Normal B




A

3.CHECK ENGINE IMMOBILISER SYSTEM

B

4.READ FREEZE FRAME DATA
3.CHECK ENGINE IMMOBILISER SYSTEM
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Idle the engine


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Immobiliser Communication and Immobiliser Fuel Cut.

Powertrain > Engine > Data List
Tester Display
Immobiliser Communication
Immobiliser Fuel Cut
50003 61 523,681

e.

Check the Data List indication.

OK:
Data List Item Result
Immobiliser Communication ON
Immobiliser Fuel Cut OFF



Result:
Proceed to
OK
NG



OK

4.READ FREEZE FRAME DATA

NG

4.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Problem Symptom Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Closed Throttle Position SW Engine Speed Total of Short FT and Long FT
When idling or decelerating, engine speed slowly decreases and engine stalls All 5 sets of freeze frame data are ON Decreases slowly*1 All 5 sets of freeze frame data are +15% or more*2
·

Air suction

·

Sensor malfunction (value from sensor too lean)

·

Fuel supply problem


A
At least 1 of the 5 sets of freeze frame data is -15% or less*3 Sensor malfunction (value from sensor too rich) B
All 5 sets of freeze frame data are from -15% to +15%
·

Intake air volume insufficient

·

Ignition timing incorrect


C
When idling or decelerating, engine speed rapidly decreases and engine stalls Decreases rapidly*1 -
·

Injection stoppage, ignition stoppage

·

Load from external parts


D


A215381
0.073,0.073 2.177,0.24 2.104,0.167 10 false Rapid Decrease in Engine Speed 2.333,0.417 2.698,0.604 0.365,0.188 10 false (rpm) 2.385,0.76 2.667,0.906 0.281,0.146 10 false 800 2.385,0.969 2.667,1.115 0.281,0.146 10 false 600 2.385,1.156 2.667,1.302 0.281,0.146 10 false 400 2.385,1.354 2.667,1.5 0.281,0.146 10 false 200 2.552,1.573 2.698,1.719 0.146,0.146 10 false 0 3.042,1.646 3.24,1.802 0.198,0.156 10 false #1 3.469,1.646 3.667,1.802 0.198,0.156 10 false #2 3.938,1.646 4.135,1.802 0.198,0.156 10 false #3 4.156,1.646 4.354,1.802 0.198,0.156 10 false #4 4.375,1.646 4.573,1.802 0.198,0.156 10 false #5 4.99,1.135 6.063,1.292 1.073,0.156 10 false 400 rpm or more 1.219,1.021 2.125,1.208 0.906,0.188 10 false Engine Speed 2.698,1.979 4.854,2.208 2.156,0.229 10 false Freeze Frame Data Storage Point

HINT:
·

*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.

Otherwise, the engine speed is considered to have decreased slowly.

1. In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.

2. In the freeze frame data, the engine speed at #5 is 120 rpm or less.

·

*2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.

·

*3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.





A

5.CHECK INTAKE SYSTEM

B

33.CHECK IGNITION SYSTEM

C

52.CHECK IGNITION SYSTEM

D

64.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
5.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air suction.



Result:
Proceed to
OK
NG



OK

6.CHECK PURGE VSV

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK PURGE VSV
a.
A172615

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Start the engine.


c.

Idle the engine.


d.

Disconnect the connector of the purge VSV.


e.

Check if air flows through the purge VSV.

OK:

Air does not flow.



f.

Connect the connector of the purge VSV.


g.

Connect the purge hose of the purge VSV.

HINT:

When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DTC CHECK / CLEAR



Result:
Proceed to
OK
NG



OK

7.READ FREEZE FRAME DATA

NG

7.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Stop Light Switch At least 1 of the 5 sets of freeze frame data is ON Air suction from brake booster A
All 5 sets of freeze frame data are OFF - B




A

8.READ VALUE USING INTELLIGENT TESTER (SHORT FT)

B

10.CHECK IGNITION SYSTEM
8.READ VALUE USING INTELLIGENT TESTER (SHORT FT)
a.
A217928
0.219,0.594 0.927,0.76 0.708,0.167 10 Depressed 0.094,0.073 0.906,0.229 0.813,0.156 10 Brake Pedal 0.313,1.115 0.938,1.271 0.625,0.156 10 Released 0.115,1.719 2.26,1.875 2.146,0.156 10 Short FT #1 2.51,2.25 3.26,2.583 0.75,0.333 10 Change is 10% or less

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



d.

Idle the engine.


e.

Using the intelligent tester, read the value of Short FT #1 in the Data List while depressing the brake pedal.

Powertrain > Engine > Data List
Tester Display
Short FT #1
50003 61 310
Standard:

Short FT #1 changes by +10% or less.


HINT:

When air leakage from the brake booster is present, the feedback compensation increases because the air-fuel ratio becomes lean.



Result:
Proceed to
OK
NG



OK

9.PERFORM DRIVE TEST

NG

9.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Short FT #1 in the Data List.

Powertrain > Engine > Data List
Tester Display
Short FT #1
Long FT #1
50003 61 310,311
Standard:
Data List Condition Specified Condition
Short FT #1 + Long FT #1 The conditions of the vehicle are matched to those present when the problem occurs -15 to +15%



Result:
Proceed to
OK
NG



OK

10.CHECK IGNITION SYSTEM

NG

10.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

11.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

11.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load Below 90% of the current value of the vehicle*1 Mass air flow meter A
AFS Voltage B1S1 3.3 V or higher*2
·

Air fuel ratio sensor

·

Wire harness or connector


B


HINT:
·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.

·

*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.





A

12.CHECK MASS AIR FLOW METER

B

15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
12.CHECK MASS AIR FLOW METER
a.

Remove the mass air flow meter.


b.

Check for foreign matter in the airflow passage of the mass airflow meter.

Result:
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B




A

13.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

13.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0102

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

14.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Calculate Load in the Data List.

Powertrain > Engine > Data List
Tester Display
Calculate Load
50003 61 308
Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle


Result:
Result Proceed to
Abnormal A
Normal B




A

B

18.READ FREEZE FRAME DATA
15.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A301616
0.823,0.344 1.979,0.594 1.156,0.25 10 false Injection Volume 1.083,0.75 1.677,1 0.594,0.25 10 false +12.5% 1.115,1.063 1.708,1.313 0.594,0.25 10 false -12.5% 0.688,1.76 3.073,2.073 2.385,0.313 10 false Air Fuel Ratio Sensor Output Voltage 0.552,2.208 1.74,2.458 1.188,0.25 10 false Higher than 3.4 V 0.875,2.594 1.708,2.854 0.833,0.26 10 false Below 3.1 V 3.021,2.396 3.302,2.635 0.281,0.24 10 false OK 2.979,3.958 3.26,4.198 0.281,0.24 10 false OK 0.635,3.313 3.021,3.625 2.385,0.313 10 false Heated Oxygen Sensor Output Voltage 0.51,3.771 1.698,4.021 1.188,0.25 10 false Higher than 0.55 V 0.906,4.146 1.75,4.406 0.844,0.26 10 false Below 0.4 V

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine > Active Test
Tester Display
Control the Injection Volume for A/F Sensor
50004 61 2

f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
Intelligent tester Display Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result:
Result Proceed to
Abnormal A
Normal B


HINT:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.




A

16.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)

B

18.READ FREEZE FRAME DATA
16.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0031 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0031

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

17.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P2237

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

18.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

19.READ FREEZE FRAME DATA

B

21.READ FREEZE FRAME DATA
19.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

A217929
0.469,0.854 2.802,1.24 2.333,0.385 10 Engine Coolant Temperature Increase after Engine Start 3.406,0.052 3.76,0.292 0.354,0.24 10 (°C) 5.604,2.135 6.24,2.313 0.635,0.177 10 (Minutes) 5.135,1.698 5.292,1.854 0.156,0.156 10 A 4.948,0.781 5.104,0.938 0.156,0.156 10 C 3.875,0.49 4.031,0.646 0.156,0.156 10 B 3.604,2.427 5.635,2.656 2.031,0.229 10 Time Elapsed after Engine Start 0.469,1.198 2.792,1.698 2.323,0.5 10 (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start)

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature sensor B
Range C - C


HINT:

This step is not directly related to engine stall.




A

20.INSPECT THERMOSTAT

B

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

24.READ FREEZE FRAME DATA
20.INSPECT THERMOSTAT
HINT:

For the thermostat inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE COOLING>THERMOSTAT>INSPECTION


Result:
Result Proceed to
Abnormal A
Normal B



A

B

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
21.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B




A

22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

24.READ FREEZE FRAME DATA
22.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Result Proceed to
Normal A
Abnormal B



A

23.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

B

23.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-32 (THW) - C17-2 Always Below 1 Ω
C75-28 (E2) - C17-1 Always Below 1 Ω
C75-32 (THW) or C17-2 - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

24.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
EVAP (Purge) VSV At least 1 of the 5 sets of freeze frame data is not 0% Purge VSV A
All 5 sets of freeze frame data are 0% - B


HINT:

If the purge VSV is stuck closed, air-fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.




A

25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)

B

44.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
25.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A200511
0.615,0.208 1.26,0.479 0.646,0.271 10 false VSV ON 2.323,0.198 3.063,0.458 0.74,0.26 10 false VSV OFF 0.719,1.542 1.365,1.813 0.646,0.271 10 false Air flows 2.188,1.552 3.281,1.813 1.094,0.26 10 false Air does not flow

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 61 6

f.

Operate the purge VSV and check the airflow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result:
Result Proceed to
NG A
OK B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

26.INSPECT PURGE VSV

B

44.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
26.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)

NG

27.CHECK TERMINAL VOLTAGE (PURGE VSV POWER SOURCE)
a.
A161605
0.396,1.958 0.781,2.188 0.385,0.229 0.198,0.219 0.51,0.375 0.313,0.156 10 false *a 0.469,1.99 0.865,2.229 0.396,0.24 10 false C69
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C69-2 - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

28.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C69-1 - C76-23 (PRG) Always Below 1 Ω
C69-1 or C76-23 (PRG) - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

29.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Result:
Proceed to
NEXT



NEXT

30.READ VALUE USING INTELLIGENT TESTER (EVAP (Purge) VSV)
30.READ VALUE USING INTELLIGENT TESTER (EVAP (Purge) VSV)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine for 15 minutes or more.


d.

Using the intelligent tester, read the value of EVAP (Purge) VSV in the Data List.

Powertrain > Engine > Data List
Tester Display
EVAP (Purge) VSV
50003 61 60
Standard:
Data List Specified Condition
EVAP (Purge) VSV Value other than 0% is displayed


Result:
Result Proceed to
Abnormal A
Normal B




A

31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

31.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.
A200511
0.604,0.229 1.333,0.521 0.729,0.292 10 false VSV ON 2.281,0.229 3.01,0.521 0.729,0.292 10 false VSV OFF 0.688,1.583 1.365,1.844 0.677,0.26 10 false Air flows 2.177,1.583 3.302,1.823 1.125,0.24 10 false Air does not flow

Disconnect the purge hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine > Active Test
Tester Display
Activate the VSV for Evap Control
50004 61 6

f.

Operate the purge VSV and check the airflow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result:
Result Proceed to
NG A
OK B



HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



A

32.CHECK CONNECTOR CONNECTION CONDITION (ECM)

B

32.CHECK CONNECTOR CONNECTION CONDITION (ECM)
a.

Check the ECM connector connection condition.

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

NG

RECONNECT CONNECTOR CORRECTLY

33.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

34.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

34.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Calculate Load 110% or more of the current value of the vehicle*1 Mass air flow meter A
AFS Voltage B1S1 Below 3.3 V*2
·

Air fuel ratio sensor

·

Harness and connector


B
Both freeze frame data items listed above Values are other than above - C


HINT:
·

*1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.

·

*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.





A

35.CHECK MASS AIR FLOW METER

B

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

C

41.READ FREEZE FRAME DATA
35.CHECK MASS AIR FLOW METER
a.

Remove the mass airflow meter.


b.

Check for foreign matter in the airflow passage of the mass air flow meter.

Result:
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B




A

36.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

36.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0102

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

37.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Calculate Load in the Data List.

Powertrain > Engine > Data List
Tester Display
Calculate Load
50003 61 308
Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle



Result:
Proceed to
OK
NG



OK

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.
A301616
0.823,0.344 1.979,0.594 1.156,0.25 10 false Injection Volume 1.083,0.75 1.677,1 0.594,0.25 10 false +12.5% 1.115,1.063 1.708,1.313 0.594,0.25 10 false -12.5% 0.688,1.76 3.073,2.073 2.385,0.313 10 false Air Fuel Ratio Sensor Output Voltage 0.552,2.208 1.74,2.458 1.188,0.25 10 false Higher than 3.4 V 0.875,2.594 1.708,2.854 0.833,0.26 10 false Below 3.1 V 3.021,2.396 3.302,2.635 0.281,0.24 10 false OK 2.979,3.958 3.26,4.198 0.281,0.24 10 false OK 0.635,3.313 3.021,3.625 2.385,0.313 10 false Heated Oxygen Sensor Output Voltage 0.51,3.771 1.698,4.021 1.188,0.25 10 false Higher than 0.55 V 0.906,4.146 1.75,4.406 0.844,0.26 10 false Below 0.4 V

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.


d.

Idle the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

Powertrain > Engine > Active Test
Tester Display
Control the Injection Volume for A/F Sensor
50004 61 2

f.

Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.

Standard:
Intelligent tester Display Specified Condition
Control the Injection Volume for A/F Sensor (+12.5%) Air fuel ratio sensor output voltage is below 3.1 V
Control the Injection Volume for A/F Sensor (-12.5%) Air fuel ratio sensor output voltage is higher than 3.4 V


Result:
Result Proceed to
Abnormal A
Normal B


HINT:

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.




A

39.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)

B

41.READ FREEZE FRAME DATA
39.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR POWER SOURCE)
a.

Check the harnesses and connectors, referring to DTC P0031 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0031

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

40.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

40.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Check the harnesses and connectors, referring to DTC P2237 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P2237

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

41.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Proceed to
Initial Engine Coolant Temp, Ambient Temp for A/C, Initial Intake Air Temp Difference in temperature between each item is less than 10°C*1 A
Difference in temperature between each item is 10°C or more*2 B


HINT:
·

*1: A long time had elapsed after stopping the engine.

·

*2: A long time had not elapsed after stopping the engine.





A

42.READ FREEZE FRAME DATA

B

46.READ FREEZE FRAME DATA
42.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

A217929
0.469,0.854 2.802,1.24 2.333,0.385 10 Engine Coolant Temperature Increase after Engine Start 3.406,0.052 3.76,0.292 0.354,0.24 10 (°C) 5.604,2.135 6.24,2.313 0.635,0.177 10 (Minutes) 5.135,1.698 5.292,1.854 0.156,0.156 10 A 4.948,0.781 5.104,0.938 0.156,0.156 10 C 3.875,0.49 4.031,0.646 0.156,0.156 10 B 3.604,2.427 5.635,2.656 2.031,0.229 10 Time Elapsed after Engine Start 0.469,1.198 2.792,1.698 2.323,0.5 10 (Engine Coolant Temperature - Engine Coolant Temperature at Engine Start)

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Initial Engine Coolant Temp, Coolant Temp, Engine Run Time Range A
·

Engine coolant temperature sensor

·

Thermostat


A
Range B Engine coolant temperature B
Range C - C


HINT:

This step is not directly related to engine stall.




A

43.INSPECT THERMOSTAT

B

47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

C

76.CHECK FUEL SYSTEM
43.INSPECT THERMOSTAT
HINT:

For the thermostat inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE COOLING>THERMOSTAT>INSPECTION


Result:
Result Proceed to
Abnormal A
Normal B


HINT:

This step is not directly related to engine stall.



A

B

47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
44.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5

e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 45.





A

45.INSPECT FUEL PUMP

B

49.CHECK FUEL SYSTEM
45.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

NG

46.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Coolant Temp 120°C or higher Engine coolant temperature sensor A
Coolant Temp, Ambient Temp for A/C Engine coolant temperature is lower than outside temperature by 15°C or more Engine coolant temperature sensor
Both freeze frame data items listed above Values are other than above - B




A

47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

56.CLEAR DTC
47.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Result Proceed to
Normal A
Abnormal B



A

48.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

B

48.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-32 (THW) - C17-2 Always Below 1 Ω
C75-28 (E2) - C17-1 Always Below 1 Ω
C75-32 (THW) or C17-2 - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test.



HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Abnormal A
Normal B



A

50.CHECK FUEL SYSTEM

B

50.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

51.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

51.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test.



HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

52.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

53.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

53.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Result Suspected Area Proceed to
Total of ISC Learning Value and ISC Feedback Value Below 80% of the current value of the vehicle Intake air volume insufficient A
80% or more of the current value of the vehicle B




A

54.CHECK INTAKE SYSTEM

B

57.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
54.CHECK INTAKE SYSTEM
a.

Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.].

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.

·

If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.



OK:

There is no air leakage.



Result:
Proceed to
OK
NG



OK

55.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE INTAKE SYSTEM

55.CHECK INTAKE SYSTEM
a.

Check the intake system.

·

Inspect the brake booster assembly.

·

Inspect the mass air flow meter.

·

Check the PCV hose.

·

Inspect the PCV valve.

·

Inspect the purge VSV.


Result:
Result Proceed to
Abnormal A
Normal B




A

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

B

61.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
56.CLEAR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Result:
Proceed to
NEXT



NEXT

END

57.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the Techstream on.


c.

Warm up the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank1).

Powertrain > Engine > Active Test
Tester Display
Control the VVT Linear (Bank1)
50004 61 32
HINT:

When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.



e.

Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.

OK:
Intelligent tester Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.

·

If the camshaft timing oil control valve is stuck on, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.




Result:
Proceed to
OK
NG



OK

58.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

58.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Check the harnesses and connectors, referring to DTC P0010 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0010

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

59.READ FREEZE FRAME DATA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.READ FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more Less than 3°
·

Engine coolant temperature sensor

·

Mass air flow meter

·

Knock sensor


A
3° or more - B
Differs from the current value of the vehicle by less than 10° - -




A

60.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

B

60.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
HINT:

For the engine coolant temperature sensor inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

61.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)

NG

61.CHECK HARNESS AND CONNECTOR (ECM - ENGINE COOLANT TEMPERATURE SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the engine coolant temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-32 (THW) - C17-2 Always Below 1 Ω
C75-28 (E2) - C17-1 Always Below 1 Ω
C75-32 (THW) or C17-2 - Body ground Always 10 kΩ or higher


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

62.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

62.INSPECT MASS AIR FLOW METER (INTAKE AIR TEMPERATURE SENSOR)
a.

Inspect the mass air flow meter.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION

HINT:

If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.



Result:
Proceed to
OK
NG



OK

63.READ VALUE USING INTELLIGENT TESTER

NG

63.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of IGN Advance and Knock Correct Learn Value in the Data List.

Powertrain > Engine > Data List
Tester Display
IGN Advance
Knock Correct Learn Value
50003 61 317,80
Result:
Data List Item Proceed to
IGN Advance Knock Correct Learn Value
Differs from the current value of the vehicle by 10° or more Less than 3° A
3° or more B
Differs from the current value of the vehicle by less than 10° -


HINT:

If the results of the checks performed in steps 57 to 65 were all normal and the sum of ISC Feedback Value and ISC Learning Value in the Data List is 120% of the normal value or more, check for carbon deposits in the throttle body assembly. If there are carbon deposits, clean them off to finish the troubleshooting procedure.




A

B

END

64.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
a.
A208644
0.385,0.802 0.677,1 0.292,0.198 0.385,1.063 0.677,1.26 0.292,0.198 0.385,1.313 0.677,1.51 0.292,0.198 0.385,1.563 0.677,1.76 0.292,0.198 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.417,0.823 0.75,1.01 0.333,0.188 10 false C65 0.448,1.083 0.781,1.271 0.333,0.188 10 false C2 0.417,1.333 0.75,1.521 0.333,0.188 10 false C66 0.448,1.583 0.781,1.771 0.333,0.188 10 false C4
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 C65-1 - Body ground Ignition switch ON 11 to 14 V
No. 2 C2-1 - Body ground Ignition switch ON 11 to 14 V
No. 3 C66-1 - Body ground Ignition switch ON 11 to 14 V
No. 4 C4-1 - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

65.CHECK IGNITION SYSTEM

NG

65.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

66.CHECK FREEZE FRAME DATA

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

66.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
A/C Signal Air Conditioner FB Val Power Steering Signal
A/C Signal display does not change from OFF*1 - Does not change from OFF - A
Changes from OFF to ON Power steering system
A/C Signal display changes from OFF to ON*1 Value displayed for Air Conditioner FB Val does not increase Changes from OFF to ON
Does not change from OFF -
Value displayed for Air Conditioner FB Val increases - A/C system B


HINT:
·

*1: Check not only the on/off state of the air conditioner but also the change in air conditioner load.

·

Even if the results are normal, the power steering system and/or A/C system may have been malfunctioning. If there are no problems with other parts, inspect the power steering system and/or A/C system.





A

67.CHECK FREEZE FRAME DATA

B

67.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item for DTC P1605 Suspected Area Proceed to
Electrical Load Signal or Electric Load Feedback Val Electric Load Feedback Val
Electrical Load Signal display changes from OFF to ON*3, or value displayed for Electric Load Feedback Val increases* Value displayed for Electric Load Val changes Electrical load signal circuit A
Value displayed for Electric Load Val does not change - B
Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase - -


HINT:
·

*: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.

·

The normal value for the ISC learned value is engine displacement (liters) x 0.9.





A

B

68.CHECK FREEZE FRAME DATA
68.CHECK FREEZE FRAME DATA
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>FREEZE FRAME DATA

Result:
Freeze Frame Data Item Result Suspected Area Proceed to
Throttle Sensor Position, Calculate Load Calculate Load decreases while Throttle Sensor Position increases Mass air flow meter A
Calculate Load does not decrease while Throttle Sensor Position increases - B




A

69.CHECK MASS AIR FLOW METER

B

72.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
69.CHECK MASS AIR FLOW METER
a.

Remove the mass air flow meter.


b.

Check for foreign matter in the airflow passage of the mass airflow meter.

Result:
Result Proceed to
Visible foreign matter is not present A
Visible foreign matter is present B




A

70.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

70.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Check the harnesses and connectors, referring to DTC P0102 procedure.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0102

HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.




Result:
Proceed to
OK
NG



OK

71.PERFORM DRIVE TEST

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

71.PERFORM DRIVE TEST
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up until the engine coolant temperature stabilizes.

HINT:

The A/C switch and all accessory switches should be off.



c.

Idle the engine.


d.

Using the intelligent tester, read the value of Calculate Load in the Data List.

Powertrain > Engine > Data List
Tester Display
Calculate Load
50003 61 308
Standard:
Data List Specified Condition
Calculate Load 90 to 110% of the current value of the vehicle



Result:
Proceed to
OK
NG



OK

72.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)

NG

72.CHECK TERMINAL VOLTAGE (FUEL INJECTOR POWER SOURCE)
a.
A208644
0.385,0.802 0.677,1 0.292,0.198 0.385,1.063 0.677,1.26 0.292,0.198 0.385,1.313 0.677,1.51 0.292,0.198 0.385,1.563 0.677,1.76 0.292,0.198 0.125,0.063 0.438,0.219 0.313,0.156 10 false *a 0.417,0.823 0.75,1.01 0.333,0.188 10 false C65 0.448,1.083 0.781,1.271 0.333,0.188 10 false C2 0.417,1.333 0.75,1.521 0.333,0.188 10 false C66 0.448,1.583 0.781,1.771 0.333,0.188 10 false C4
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Cylinder Tester Connection Switch Condition Specified Condition
No. 1 C65-1 - Body ground Ignition switch ON 11 to 14 V
No. 2 C2-1 - Body ground Ignition switch ON 11 to 14 V
No. 3 C66-1 - Body ground Ignition switch ON 11 to 14 V
No. 4 C4-1 - Body ground Ignition switch ON 11 to 14 V


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

Make sure there is not an excessive amount of force applied to the wire harness.

·

A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)




Result:
Proceed to
OK
NG



OK

73.CHECK IGNITION SYSTEM

NG

73.CHECK IGNITION SYSTEM
a.

Perform ignition system On-vehicle Inspection.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

74.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

74.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5

e.

When performing the Active Test, check for an operating sound from the fuel pump.

Standard:
Control the Fuel Pump / Speed Specified Condition
ON Operating sound heard
OFF Operating sound not heard


Result:
Result Proceed to
Abnormal A
Normal B


HINT:
·

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.

·

While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.

·

If the fuel pump operating noise is abnormal, proceed to step 78.





A

75.INSPECT FUEL PUMP

B

76.CHECK FUEL SYSTEM
75.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

NG

76.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.

·

Perform the Active Test.


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Result Proceed to
Abnormal A
Normal B




A

77.CHECK FUEL SYSTEM

B

77.CHECK FUEL SYSTEM
a.

Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.

Result:
Result Proceed to
There is foreign matter or signs that fuel pump was stuck A
There is no foreign matter and no signs that fuel pump was stuck B


HINT:

If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.




A

78.CHECK FUEL SYSTEM

B

REPAIR OR REPLACE FUEL SYSTEM

78.CHECK FUEL SYSTEM
a.

Check the fuel system.

·

Check the fuel pump operation.

·

Check the fuel leaks.

·

Check the fuel pressure.


HINT:

For the fuel system On-vehicle Inspection, refer to the following procedures.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION



Result:
Proceed to
OK
NG



OK

END

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA