Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0130  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1)  


DESCRIPTION

The heated oxygen sensor is used to monitor oxygen concentration in the exhaust gas.

The ECM uses the heated oxygen sensor information to regulate the air-fuel ratio and keep it close to the stoichiometric air-fuel ratio. This maximizes the ability of the Three-way Catalytic Converter (TWC) to purify the exhaust gases.

The heated oxygen sensor generates an output voltage between 0.1 V and 0.9 V in response to the oxygen concentration in the exhaust gas.

The heated oxygen sensor output voltage changes dramatically in the vicinity of the stoichiometric air-fuel ratio.

If the oxygen concentration in the exhaust gas increases, the air-fuel ratio is lean and the heated oxygen sensor output voltage to the ECM drops below 0.45 V. If the oxygen concentration in the exhaust gas decreases, the air-fuel ratio is rich and the heated oxygen sensor output voltage to the ECM increases to above 0.45 V.

The heated oxygen sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty cycle approach to adjust the average current in the sensor heater element.

A103844
1.781,2.469 2.021,2.385 false 1.583,2.479 1.271,2.365 false 3.25,1.729 3.604,1.615 false 2.833,2.094 3.604,2.042 false 2.917,2.365 3.604,2.521 false 2.771,2.25 3.594,2.042 false 2.771,1.49 3.021,0.99 false 0.708,2.281 1.427,2.51 0.719,0.229 10 false Element 0.177,3.344 1.208,3.573 1.031,0.229 10 false Exhaust Gas 2.625,2.969 3.646,3.198 1.021,0.229 10 false A - A Section 3.646,1.979 5.094,2.208 1.448,0.229 10 false Platinum Element 5.135,0.677 6.865,0.906 1.729,0.229 10 false Ideal Air-fuel Mixture 5.115,2.615 7.01,2.885 1.896,0.271 10 false Rich - Air-fuel Ratio - Lean 2.052,2.292 2.771,2.521 0.719,0.229 10 false Cover 3.635,1.531 4.354,1.76 0.719,0.229 10 false Heater 3.635,2.458 4,2.688 0.365,0.229 10 false Air 1.208,2.844 1.354,3.042 0.146,0.198 10 false A 1.958,2.844 2.104,3.042 0.146,0.198 10 false A 3.073,0.781 4.208,1.198 1.135,0.417 10 false Solid Electrolyte (Zirconia Element) 4.583,1.01 5.063,1.438 0.479,0.427 10 false Output Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0130 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1) Heated oxygen sensor output voltage is below 0.45 V for 75 seconds or more (1 trip detection logic).
·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

ECM


- DTC stored

HINT:
·

The internal resistance of the heated oxygen sensor (sensor 1) cannot be measured using a tester.

·

Sensor 1 refers to the sensor closer to the engine assembly.

·

The output voltage of the heated oxygen sensor and the short-term fuel trim value can be read using the intelligent tester.



MONITOR DESCRIPTION

After the engine is started and the temperature of the heated oxygen sensor element is presumed to have reached the activation temperature, if the output from the heated oxygen sensor is below a set value, the system forces the air-fuel ratio to become rich. If the output from the heated oxygen sensor is below the threshold even after that, the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor
Required Sensors/Components (Related) Engine coolant temperature sensor, Throttle position sensor, Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

This confirmation driving pattern is used in the "Perform Confirmation Driving Pattern" step of the following diagnostic troubleshooting procedure.

A085081
0.438,0.5 1.583,0.708 1.146,0.208 10 false Vehicle Speed 0.24,1.083 1.365,1.292 1.125,0.208 10 false 40 km/h (25 mph) 1.542,1.99 2.396,2.229 0.854,0.24 10 false Warming up 0.979,1.531 1.406,1.833 0.427,0.302 10 false Idling 2.552,1.188 2.885,1.438 0.333,0.25 10 false [B] 3.042,1.479 3.292,1.688 0.25,0.208 10 false [C] 3.542,1.188 3.844,1.438 0.302,0.25 10 false [B] 4.531,1.188 4.833,1.479 0.302,0.292 10 false [B] 4.031,1.479 4.281,1.688 0.25,0.208 10 false [C] 5.021,1.479 5.26,1.698 0.24,0.219 10 false [D] 5.354,1.479 5.688,1.729 0.333,0.25 10 false [E] 1.802,1.469 2.052,1.677 0.25,0.208 10 false [A] 2.188,0.302 3.104,0.667 0.917,0.365 10 false 20 seconds or more 3.219,0.302 4.135,0.667 0.917,0.365 10 false 20 seconds or more 4.25,0.302 5.167,0.667 0.917,0.365 10 false 20 seconds or more 2.844,1.99 3.76,2.198 0.917,0.208 10 false 20 seconds 3.813,1.99 4.729,2.198 0.917,0.208 10 false 20 seconds 4.813,1.99 5.729,2.198 0.917,0.208 10 false 30 seconds

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the intelligent tester on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the intelligent tester on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

8.

Drive the vehicle at 40 km/h (25 mph) or more for 20 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Let the engine idle for 20 seconds or more [C].

10.

Repeat steps [B] and [C] above at least 3 times in one driving cycle.

11.

Let the engine idle for 30 seconds or more [D].

12.

Enter the following menus: Powertrain / Engine and ECT / DTC [E].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0130.

16.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A247766
5.74,0.458 6.333,0.74 0.594,0.281 10 false HA1A 4.188,0.438 4.635,0.667 0.448,0.229 10 false HT1A 5.5,0.385 5.615,0.542 0.115,0.156 10 false 1 5.406,0.552 5.802,0.781 0.396,0.229 10 false C75 5.406,1.333 5.948,1.604 0.542,0.271 10 false C75 5.406,2.01 5.854,2.25 0.448,0.24 10 false C75 5.75,1.229 6.302,1.448 0.552,0.219 10 false A1A+ 4.177,1.198 4.656,1.427 0.479,0.229 10 false OX1A 5.458,1.146 5.802,1.385 0.344,0.24 10 false 21 5.458,1.833 5.74,2.021 0.281,0.188 10 false 28 5.74,1.917 6.031,2.146 0.292,0.229 10 false E2 3.781,1.198 4.083,1.427 0.302,0.229 10 false E2 5.74,3.104 6.385,3.417 0.646,0.313 10 false MREL 5.5,2.938 5.708,3.156 0.208,0.219 10 false 8 5.406,3.104 5.885,3.396 0.479,0.292 10 false G89 4.969,2.385 5.677,2.615 0.708,0.229 10 false Shielded 3.406,1.729 5.031,2.031 1.625,0.302 10 false Heated Oxygen Sensor 3.406,1.594 3.771,1.813 0.365,0.219 10 false C78 3.792,0.438 4.177,0.688 0.385,0.25 10 false +B 6.198,3.854 6.542,4.01 0.344,0.156 10 false ECM 4.635,0.458 4.76,0.625 0.125,0.167 10 false 1 3.625,0.458 3.75,0.625 0.125,0.167 10 false 2 4.635,1.25 4.76,1.417 0.125,0.167 10 false 3 3.625,1.25 3.75,1.417 0.125,0.167 10 false 4 2.281,0.99 2.656,1.24 0.375,0.25 10 false 1J 2.323,0.813 2.438,0.969 0.115,0.156 10 false 2 2.281,0.552 2.563,0.74 0.281,0.188 10 false 1J 2.323,0.396 2.438,0.552 0.115,0.156 10 false 5 2.281,1.427 2.615,1.615 0.333,0.188 10 false 1J 2.323,1.25 2.563,1.469 0.24,0.219 10 false 3 0.552,1.604 0.823,1.823 0.271,0.219 10 false 1H 0.823,1.594 1.01,1.76 0.188,0.167 10 false 1 0.875,0.677 1.25,0.854 0.375,0.177 10 false EFI 1.469,1.292 1.958,1.573 0.49,0.281 10 false MAIN 0.729,2.5 1.563,2.781 0.833,0.281 10 false BATT P/I 0.927,3.771 1.604,4.083 0.677,0.313 10 false Battery 1.021,1.792 2.594,2.073 1.573,0.281 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC
a.

Connect the intelligent tester to the DLC3.


b.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

c.

Read the DTCs.

Result:
Result Proceed to
DTC P0130 is output A
DTC P0130 and other DTCs are output B


HINT:

If any DTCs other than P0130 are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the intelligent tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.

Powertrain > Engine > Data List
Tester Display
O2S B1S1
50003 61 322

d.

Warm up the heated oxygen sensor at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Read the output voltage of the heated oxygen sensor during engine idling.

Standard:

Fluctuates between less than 0.4 V and more than 0.6 V (see the following figure).


A099192
1.427,0.5 1.75,0.708 0.323,0.208 10 false 1 V 1.313,0.813 1.729,1.021 0.417,0.208 10 false 0.6 V 1.313,1.125 1.729,1.333 0.417,0.208 10 false 0.4 V 1.438,1.448 1.76,1.656 0.323,0.208 10 false 0 V


Result:
Proceed to
OK
NG



OK

3.PERFORM CONFIRMATION DRIVING PATTERN

NG

6.CHECK PCV HOSE
3.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0130 IS OUTPUT AGAIN)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0130 IS OUTPUT AGAIN)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

d.

Input DTCs: P0130.


e.

Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the drive pattern again but increase the vehicle speed.

Result:
Display (DTC Output) Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P0130 output)
B




A

5.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

5.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO

6.CHECK PCV HOSE
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>2TR-FE EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/o Secondary Air Injection System)>ON-VEHICLE INSPECTION

OK:

PCV hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

7.INSPECT HEATED OXYGEN SENSOR

NG

REPAIR OR REPLACE VENTILATION HOSE

7.INSPECT HEATED OXYGEN SENSOR

OK

8.INSPECT NO. 1 INTEGRATION RELAY (MAIN) (POWER SOURCE VOLTAGE)

NG

8.INSPECT NO. 1 INTEGRATION RELAY (MAIN) (POWER SOURCE VOLTAGE)
a.
G039047
1.313,0.271 1.625,0.49 0.313,0.219 1.396,0.302 1.708,0.5 0.313,0.198 10 false 1J 1.823,0.896 2.135,1.094 0.313,0.198 10 false 1 1.708,0.906 2.021,1.104 0.313,0.198 10 false 2 1.604,0.906 1.917,1.104 0.313,0.198 10 false 3 1.5,0.896 1.813,1.094 0.313,0.198 10 false 4 1.365,0.906 1.677,1.104 0.313,0.198 10 false 5 1.25,0.906 1.563,1.104 0.313,0.198 10 false 6 1.146,0.906 1.458,1.104 0.313,0.198 10 false 7 1.031,0.906 1.344,1.104 0.313,0.198 10 false 8

Remove the No. 1 integration relay from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1J-5 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the heated oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C78-1 (HT1A) - C75-1 (HA1A) Always Below 1 Ω
C78-3 (OX1A) - C75-21 (A1A+) Always Below 1 Ω
C78-4 (E2) - Body ground Always Below 1 Ω
C78-1 (HT1A) or C75-1 (HA1A) - Body ground Always 10 kΩ or higher
C78-3 (OX1A) or C75-21 (A1A+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leakage.

Click hereEngine / Hybrid System>2TR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leakage from intake system.



Result:
Proceed to
OK
NG



OK

11.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

11.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

12.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

12.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injector pattern is poor).

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE FUEL INJECTOR ASSEMBLY