Home › Engine / Hybrid System › 1KD-FTV ENGINE MECHANICAL › CYLINDER HEAD GASKET(w/ Glow Plug Controller) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009573 1KD-FTV ENGINE MECHANICAL _0052158 CYLINDER HEAD GASKET(w/ Glow Plug Controller) A

1KD-FTV ENGINE MECHANICAL  CYLINDER HEAD GASKET(w/ Glow Plug Controller)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL CYLINDER HEAD GASKET

a.
A301938
2.604,0.563 2.802,0.365 2.802,0.365 2.896,0.365 false 2.917,0.26 3.229,0.458 0.313,0.198 10 false *1 2.854,1.313 3.167,1.51 0.313,0.198 10 false *2
*1 Measuring Tip
*2 Protrusion


Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.


b.
A058134
1.219,1.896 1.594,2.083 0.375,0.188 10 false X: *1
*1 Measuring Point


Measure the piston protrusion of each cylinder at 2 points as shown in the illustration.


c.

For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

Piston protrusion:

0.005 to 0.255 mm (0.000197 to 0.0100 in.)


HINT:

After installing the piston and connecting rod assembly, if the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.



d.
A060174
2.667,0.365 2.792,0.396 false 2.938,0.646 3,0.542 false 0.594,0.26 0.458,0.385 false 0.385,0.573 0.615,0.51 false 1.125,0.438 0.771,0.604 false 0.625,0.125 0.771,0.313 0.146,0.188 10 false A 1.5,0.531 1.708,0.719 0.208,0.188 10 false *1 2.75,1.26 2.958,1.448 0.208,0.188 10 false *1 0.26,0.51 0.406,0.698 0.146,0.188 10 false B 2.552,0.292 2.698,0.479 0.146,0.188 10 false D 1.146,0.333 1.292,0.521 0.146,0.188 10 false C 2.781,0.573 2.927,0.76 0.146,0.188 10 false E
*1 Cutout Mark
V100135

Front


Select a new cylinder head gasket.

HINT:

New cylinder head gaskets are available in 5 sizes, and are marked A, B, C, D or E.


New Cylinder Head Gasket Thickness:
Mark Specified Condition
A 0.80 to 0.90 mm (0.0315 to 0.0354 in.)
B 0.85 to 0.95 mm (0.0335 to 0.0374 in.)
C 0.90 to 1.00 mm (0.0354 to 0.0394 in.)
D 0.95 to 1.05 mm (0.0374 to 0.0413 in.)
E 1.00 to 1.10 mm (0.0394 to 0.0433 in.)


i.

Select the largest piston protrusion value from the measurements made. Then select a new gasket according to the table below.

Gasket Size:
Item Specified Condition
Piston protrusion 0.005 to 0.054 mm (0.000197 to 0.00213 in.) 0.055 to 0.104 mm (0.00217 to 0.00409 in.) 0.105 to 0.154 mm (0.00413 to 0.00606 in.) 0.155 to 0.204 mm (0.00610 to 0.00803 in.) 0.205 to 0.255 mm (0.00807 to 0.0100 in.)
Gasket to be used A B C D E




e.
A060144
0.698,0.833 0.573,0.885 false
V100135

Front


Place the cylinder head gasket on the cylinder block.

NOTICE:

Make sure the gasket is installed facing the proper direction.



Hide 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

A301940
0.375,0.604 0.688,0.802 0.313,0.198 10 false 17 0.375,2.521 0.688,2.719 0.313,0.198 10 false (A) 0.74,0.5 1.052,0.698 0.313,0.198 10 false 11 0.729,0.667 1.042,0.865 0.313,0.198 10 false (B) 1.094,0.563 1.406,0.76 0.313,0.198 10 false 9 1.042,0.719 1.354,0.917 0.313,0.198 10 false (A) 1.448,0.5 1.76,0.698 0.313,0.198 10 false 3 1.406,0.646 1.719,0.844 0.313,0.198 10 false (B) 1.75,0.552 2.063,0.75 0.313,0.198 10 false 1 1.708,0.688 2.021,0.885 0.313,0.198 10 false (A) 2.135,0.51 2.448,0.708 0.313,0.198 10 false 6 2.094,0.656 2.406,0.854 0.313,0.198 10 false (B) 2.458,0.542 2.771,0.74 0.313,0.198 10 false 8 2.417,0.677 2.729,0.875 0.313,0.198 10 false (A) 2.781,0.5 3.094,0.698 0.313,0.198 10 false 14 2.781,0.646 3.094,0.844 0.313,0.198 10 false (B) 3.115,0.531 3.427,0.729 0.313,0.198 10 false 16 3.104,0.698 3.417,0.896 0.313,0.198 10 false (A) 0.385,2.385 0.698,2.583 0.313,0.198 10 false 15 0.365,0.76 0.677,0.958 0.313,0.198 10 false (A) 0.708,2.51 1.021,2.708 0.313,0.198 10 false 13 0.698,2.667 1.01,2.865 0.313,0.198 10 false (B) 1.083,2.385 1.281,2.583 0.198,0.198 10 false 7 1.406,2.521 1.604,2.719 0.198,0.198 10 false 5 1.771,2.365 1.969,2.563 0.198,0.198 10 false 2 2.104,2.51 2.302,2.708 0.198,0.198 10 false 4 2.417,2.375 2.615,2.573 0.198,0.198 10 false 10 2.75,2.51 2.948,2.708 0.198,0.198 10 false 12 3.094,2.375 3.292,2.573 0.198,0.198 10 false 18 1.031,2.542 1.344,2.74 0.313,0.198 10 false (A) 1.719,2.521 2.031,2.719 0.313,0.198 10 false (A) 2.417,2.521 2.729,2.719 0.313,0.198 10 false (A) 3.094,2.521 3.406,2.719 0.313,0.198 10 false (A) 1.365,2.688 1.677,2.885 0.313,0.198 10 false (B) 2.063,2.677 2.375,2.875 0.313,0.198 10 false (B) 2.74,2.667 3.052,2.865 0.313,0.198 10 false (B)

HINT:
·

The cylinder head bolts are tightened in 3 progressive steps.

·

If any bolt is broken or deformed, replace it.



a.

Place the cylinder head on the cylinder head gasket.


b.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


c.

Install the 18 washers with the 18 cylinder head bolts, and uniformly tighten the bolts in several passes in the sequence shown in the illustration.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
A 110 mm (4.33 in.)
B 167 mm (6.57 in.)


If any one the cylinder head bolts does not meet the torque specification, replace it.


d.
A060141
0.781,0.708 0.781,1.375 true 0.25,1.01 0.438,1.177 0.188,0.167 10 false *a 1.156,0.969 1.469,1.156 0.313,0.188 10 false 90° 1.802,0.531 2.115,0.719 0.313,0.188 10 false 90° 0.813,0.073 1.125,0.26 0.313,0.188 10 false 90° 0.052,0.479 0.365,0.667 0.313,0.188 10 false 90° 0.688,1.406 0.854,1.573 0.167,0.167 10 false *1
*1 Paint Mark
*a Front


Mark the front of each cylinder head bolt with paint.


e.

Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration.


f.

Tighten the cylinder head bolts by an additional 90°.


g.

Check that the painted marks are now facing rearward.


Hide 4.INSTALL CAMSHAFT

a.
G036616
0.573,1.635 1.177,1.792 1.177,1.792 1.25,1.792 true 0.125,1.156 0.458,1.344 0.333,0.188 10 false 90° 1.271,1.708 1.448,1.865 0.177,0.156 10 false *1
*1 Key


Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.

HINT:

Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.



b.
A060149
0.365,0.542 1.021,0.344 1.021,0.344 1.125,0.344 true 0.344,0.021 0.531,0.188 0.188,0.167 10 false *a 1.146,0.26 1.323,0.417 0.177,0.156 10 false *1
*1 Key Groove
*a Upward


Install the camshaft.

i.

Apply engine oil to the thrust portion of the camshaft.


ii.

Place the camshaft on the cylinder head with the key groove facing upward.


iii.
A060150

Align the timing marks (1-dot marks) of the camshaft drive and driven main gears and set the No. 2 camshaft in place.



c.

Remove any old seal packing (FIPG material) from the camshaft bearing cap.


d.
A060283
0.906,1.417 0.906,1.74 true 1.635,0.844 1.281,0.438 1.281,0.438 1.198,0.438 false 2.792,0.813 2.542,0.531 2.542,0.531 2.365,0.531 true 0.813,1.76 1,1.927 0.188,0.167 10 false *2 2.375,0.25 3.417,0.427 1.042,0.177 10 false 8 mm (0.315 in.) 0.99,0.323 1.177,0.49 0.188,0.167 10 false *1 2.167,0.448 2.354,0.615 0.188,0.167 10 false *1
*1 Seal Packing
*2 Oil Passage


Apply seal packing to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

4 mm (0.157 in.)


NOTICE:
·

Do not allow seal packing to contact the oil passage of the bearing cap.

·

After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.

·

Do not start the engine for at least 2 hours after installation.




e.
A060146

Install the 5 bearing caps to their proper locations.


f.
A060147
1.729,1.031 1.885,1.198 0.156,0.167 10 true 9 1.885,0.542 2.042,0.708 0.156,0.167 10 true 1 1.698,0.354 1.854,0.521 0.156,0.167 10 false 2 2.135,0.729 2.292,0.896 0.156,0.167 10 true 3 2.24,0.375 2.396,0.542 0.156,0.167 10 true 4 1.292,0.667 1.448,0.833 0.156,0.167 10 false 8 1.469,0.813 1.625,0.979 0.156,0.167 10 true 7 2.5,0.5 2.656,0.667 0.156,0.167 10 true 6 2.125,0.156 2.281,0.323 0.156,0.167 10 false 5 2.781,0.177 3.01,0.344 0.229,0.167 10 false 10 2.563,0.052 2.792,0.219 0.229,0.167 10 false 11 3.042,0.375 3.271,0.542 0.229,0.167 10 false 12 0.875,1.135 1.104,1.302 0.229,0.167 10 true 13 0.615,0.958 0.844,1.125 0.229,0.167 10 false 14 1.073,1.354 1.302,1.521 0.229,0.167 10 true 15

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


g.

Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


h.
A060145
1.854,0.771 1.063,0.771 true 0.719,0.688 1.052,0.854 0.333,0.167 10 false SST

Install a new camshaft oil seal.

i.

Apply MP grease to the lip of a new oil seal.


ii.

Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.

SST
09608-06041  



Hide 5.INSTALL CYLINDER BLOCK INSULATOR

a.

Install the cylinder block insulator to the cylinder head.


Hide 6.INSTALL NO. 2 TIMING BELT COVER

a.
A301941
0.594,2.698 0.594,2.333 true 1.625,2.063 1.625,1.698 false 2.406,2.865 2.188,2.865 true 0.51,2.74 0.823,2.938 0.313,0.198 10 false *1 1.531,2.083 1.844,2.281 0.313,0.198 10 false *1 2.448,2.76 2.76,2.958 0.313,0.198 10 false *1
*1 Seal Packing


Apply seal packing (FIPG) to the specified areas shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:

After applying seal packing, install the No. 2 timing belt cover within 3 minutes and tighten the bolts and nut within 15 minutes.



b.

Clean the bolts and their holes.


c.

Apply adhesive to 2 or 3 threads at the end of each of the 4 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.

Install the No. 2 timing belt cover with the 4 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 7.INSTALL CAMSHAFT TIMING PULLEY

a.

Install the camshaft timing pulley.


b.

Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

Torque:
98 N*m (1000 kgf*cm, 72 ft.*lbf)


Hide 11.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 12.INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).