When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
After removing the injection pipes, clean them with a brush and compressed air.
1.REMOVE NO. 1 TIMING BELT COVER
2.REMOVE TIMING BELT
3.REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY
4.REMOVE CRANKSHAFT PULLEY
5.REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)
Remove the 2 bolts and No. 2 intercooler support bracket.
6.REMOVE INTERCOOLER SUPPORT BRACKET (w/ EGR Cooler)
Remove the 2 bolts and intercooler support bracket.
7.REMOVE EXHAUST MANIFOLD WITH TURBOCHARGER
w/ EGR Cooler: (See page Engine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER(w/ EGR Cooler)>REMOVAL)
w/o EGR Cooler: (See page Engine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER(w/o EGR Cooler)>REMOVAL)
8.REMOVE VENTILATION HOSE HEAT INSULATOR (w/o EGR Cooler)
Remove the 2 bolts and ventilation hose heat insulator.
9.REMOVE NO. 2 IDLE PULLEY ASSEMBLY
10.REMOVE GENERATOR ASSEMBLY
11.REMOVE GENERATOR BRACKET
Remove the bolt and generator bracket.
12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the 4 bolts and V-ribbed belt tensioner.
13.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
Remove the 4 bolts and No. 1 compressor mounting bracket.
14.REMOVE WATER INLET
15.REMOVE THERMOSTAT
16.REMOVE WATER OUTLET
Remove the 2 bolts, water outlet and gasket.
17.REMOVE DIESEL THROTTLE BODY ASSEMBLY
18.REMOVE INTAKE MANIFOLD
w/ EGR Cooler: (See page Engine / Hybrid System>2KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/ EGR Cooler)>REMOVAL)
w/o EGR Cooler: (See page Engine / Hybrid System>2KD-FTV INTAKE / EXHAUST>INTAKE MANIFOLD(w/o EGR Cooler)>REMOVAL)
19.REMOVE NO. 2 EGR HOLE COVER PLATE (w/o EGR System)
Remove the 2 nuts, No. 2 EGR hole cover plate.
Remove the gasket.
20.REMOVE GLOW PLUG ASSEMBLY
21.REMOVE FUEL INLET PIPE SUB-ASSEMBLY
22.REMOVE OIL FILTER SUB-ASSEMBLY
23.REMOVE COMMON RAIL ASSEMBLY
24.REMOVE FUEL SUPPLY PUMP ASSEMBLY
25.REMOVE OIL COOLER COVER SUB-ASSEMBLY
26.REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)
Remove the bolt and timing gear cover insulator.
27.REMOVE VACUUM PUMP ASSEMBLY
Remove the 2 nuts, vacuum pump and 2 O-rings.
28.REMOVE VANE PUMP ASSEMBLY
Remove the 2 nuts, vane pump and O-ring.
29.REMOVE CRANKSHAFT POSITION SENSOR
30.REMOVE CAMSHAFT POSITION SENSOR
31.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
32.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
| *a | RH Side |
| *b | LH Side |
Remove the 4 bolts and front No. 1 engine mounting bracket.
33.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 4 bolts and front No. 1 engine mounting bracket.