Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE UNIT › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009575 2TR-FE ENGINE MECHANICAL _0052190 ENGINE UNIT A

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 2.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket with the 4 bolts.

Torque:
51 N*m (520 kgf*cm, 38 ft.*lbf)


Hide 3.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install a new gasket and the water by-pass pipe with the 2 nuts.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 4.INSTALL HEATER WATER OUTLET HOSE

Hide 5.INSTALL HEATER WATER INLET HOSE

Hide 6.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 7.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

NOTICE:

Install the No. 1 compressor mounting bracket exactly as described in the procedures below to properly secure and prevent damage to the fan and generator V belt.


a.
A330624

Temporarily install the No. 1 compressor mounting bracket with the 3 bolts.

HINT:

Temporarily install the No. 1 compressor mounting bracket with the 3 bolts so that the bracket can be moved by hand.



b.
A332227C01
2.24,4.438 2.552,4.635 0.313,0.198 10 false *b 1.417,3.542 1.729,3.74 0.313,0.198 10 false *a 3.073,3.552 3.281,3.75 0.208,0.198 10 false *a 0.865,2.656 1.177,2.854 0.313,0.198 10 false *c 0.698,0.24 0.833,0.438 0.135,0.198 10 true B
*a No Clearance
*b Push
*c Front


Push the No. 1 compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.

Torque:
for bolt B : 45 N*m (459 kgf*cm, 33 ft.*lbf)

HINT:

Make sure there is no clearance between the cylinder block and No. 1 compressor mounting bracket as shown in the illustration.



c.
A332228C01
2.052,0.271 2.208,0.469 0.156,0.198 10 true 1 2.365,1.198 2.521,1.396 0.156,0.198 10 true 2 1.927,1.417 2.083,1.615 0.156,0.198 10 true 3 0.552,1.292 0.677,1.458 0.125,0.167 10 true 4
V100135

Bolt A
V100136

Bolt C


Uniformly tighten the 4 bolts in the order shown in the illustration.

Torque:
for bolt A : 45 N*m (459 kgf*cm, 33 ft.*lbf)
for bolt C : 25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 8.INSTALL IDLE PULLEY ASSEMBLY (w/ Air Conditioning System)

a.

Temporarily install the idle pulley assembly with the bolt.

NOTICE:

Do not use any tools.



b.

Tighten the bolt.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 10.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)

Hide 13.INSTALL INTAKE MANIFOLD

a.

Install a new gasket.


b.
G036020N01
2.521,1.271 2.719,1.448 0.198,0.177 10 true 2 0.104,0.49 0.219,0.646 0.115,0.156 10 false 5 3.25,0.479 3.365,0.635 0.115,0.156 10 false 4 1.667,0.052 1.781,0.208 0.115,0.156 10 false 1 0.813,1.292 1.01,1.469 0.198,0.177 10 true 3 0.813,1.99 0.99,2.146 0.177,0.156 10 false 7 2.531,2 2.708,2.167 0.177,0.167 10 true 6

Install the intake manifold with the 5 bolts and 2 nuts and tighten the bolts and nuts in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Connect the crankshaft position sensor to the clamp.


Hide 15.INSTALL FUEL DELIVERY PIPE WITH FUEL INJECTOR

Hide 17.INSTALL ENGINE WIRE

a.
G038850C01
1.24,1.427 1.24,1.271 1.24,1.271 1.313,1.01 true 2.604,1.385 2.542,1.635 2.542,1.635 2.542,1.844 true 0.531,1.479 0.531,1.344 0.531,1.344 0.875,1.042 true 1.167,1.458 1.427,1.625 0.26,0.167 10 true 60° 0.458,1.479 0.719,1.646 0.26,0.167 10 true 45° 2.385,0.771 2.573,0.938 0.188,0.167 10 false *a 2.469,1.875 2.656,2.042 0.188,0.167 10 true *b
*a INCORRECT
*b Do not Allow Wires to Overlap


Connect the wire harness (engine ground wire) to the rear side of the engine with the 2 bolts so that it is within the specified range shown in the illustration.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


b.

Connect the oil pressure switch connector.


c.

Connect the noise filter connector.


d.

Connect the camshaft position sensor connector.


e.

Connect the 4 injector connectors.


f.

Connect the crankshaft position sensor connector.


g.

Connect the camshaft timing oil control valve connector.


h.

Connect the purge VSV connector.


i.

Connect the throttle body connector.


j.

Connect the engine coolant temperature sensor connector.


k.

Connect the knock sensor connector.


l.

Connect the wire harness to the clamps.


Hide 19.INSTALL PCV PIPE

a.

Install the PCV pipe with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the PCV hose to the PCV valve sub-assembly and intake manifold.