Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE › from 2012.04
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052203 ENGINE G

1GR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 5.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 6.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element.


b.

Visually check that the air cleaner filter element is not excessively damaged or oily.

If necessary, replace the air cleaner filter element.


Hide 7.INSPECT IGNITION TIMING

NOTICE:

Turn all electrical systems off.


a.

Warm up the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.


ii.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine > Data List
Tester Display
IGN Advance
50003 61 317

iii.

Inspect the ignition timing during idling.

Standard ignition timing:

7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)



iv.

Check that the ignition timing advances immediately when the engine speed is increased.



c.

When not using the intelligent tester:

i.
A206183
1.24,0.396 1.375,0.396 1.375,0.396 1.594,0.906 true 2.104,1.896 1.969,1.896 1.969,1.896 1.802,1.479 true 0.083,0.063 0.281,0.26 0.198,0.198 10 false *a 0.99,0.323 1.271,0.521 0.281,0.198 10 false CG 2.167,1.802 2.427,1.979 0.26,0.177 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Be sure not to improperly connect the terminals. This may damage the engine.



ii.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:
·

Use a timing light that detects primary signals.

·

After the inspection, be sure to wrap the wire harness with tape.




iii.

Inspect the ignition timing during idling.

Standard ignition timing:

8 to 12° BTDC @ idle (transmission in neutral and A/C switch off)



iv.

Remove SST from the DLC3.


v.

Inspect the ignition timing during idling.

Standard ignition timing:

7 to 24° BTDC @ idle (transmission in neutral and A/C switch off)



vi.

Disconnect the timing light from the engine.



Hide 8.INSPECT ENGINE IDLE SPEED

NOTICE:

Turn all the electrical systems off.


a.

Warm up the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.


ii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315

iii.

Inspect the engine idle speed.

Standard idle speed:

650 to 750 rpm (transmission in neutral and A/C switch off)




c.
A206183
0.781,1.865 0.896,1.865 0.896,1.865 1.042,1.49 true 0.052,0 0.24,0.208 0.188,0.208 10 false *a 0.469,1.771 0.792,1.948 0.323,0.177 10 false TAC
*a Front view of DLC3


When not using the intelligent tester:

i.

Connect SST to terminal 9 (TAC) of the DLC3.

SST
09843-18030  


ii.

Race the engine at 2500 rpm for approximately 90 seconds


iii.

Inspect the engine idle speed.

Standard idle speed:

650 to 750 rpm (transmission in neutral and A/C switch off)




Hide 9.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Remove the intake air surge tank (See page Engine / Hybrid System>1GR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL).



d.

Disconnect the 6 injector connectors.


e.

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole. (Procedure A)


ii.

While cranking the engine, measure the compression pressure. (Procedure B)

Compression pressure:

1300 kPa (13.3 kgf/cm2, 189 psi) or higher


Minimum pressure:

1000 kPa (10.2 kgf/cm2, 145 psi)


Difference between each cylinder:

100 kPa (1.0 kgf/cm2, 15 psi) or less


HINT:
·

Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.

·

Measure the compression in as short a time as possible.




iii.

Repeat procedures A and B for each cylinder.


iv.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat procedures A and B for cylinders with low compression.

·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.




f.

Connect the 6 injector connectors.



h.

Hide 10.INSPECT CO/HC

HINT:

This check is to determine whether or not the idle CO/HC concentration complies with regulations.


a.

Start the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.


d.

Immediately check the CO/HC concentration during idling and/or at 2500 rpm.

HINT:

When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.



e.

If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.

i.

Check the air fuel ratio sensor operation (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION) and heated oxygen sensor operation (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION).


ii.

Refer to the table below for possible causes, and then inspect and correct the corresponding causes if necessary.

CO HC Problem Possible Cause
Normal High Rough idle 1. Faulty ignitions:
·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2. Incorrect valve clearance
3. Leaky intake and exhaust valves
4. Leaky cylinders
Low High Rough idle
(Fluctuating HC reading)
1. Vacuum leaks:
·

PCV hose

·

Intake manifold

·

Throttle body


2. Lean mixture causing misfire
High High Rough idle
(Black smoke from exhaust)
1. Restricted air filter
2. Plugged PCV valve
3. Faulty SFI system:
·

Faulty pressure regulator

·

Defective engine coolant temperature sensor

·

Faulty ECM

·

Faulty injector

·

Faulty throttle position sensor

·

Faulty mass air flow sensor