1.INSTALL ENGINE WATER PUMP ASSEMBLY
Install a new gasket and the engine water pump with the 8 bolts.
2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
| *1 | New O-Ring |
Install 3 new O-rings to the timing chain cover as shown in the illustration.
Apply seal packing to the timing chain cover in a continuous line as shown in the following illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| *1 | Cylinder Head | *2 | Cylinder Block |
| *3 | Seal Packing | *4 | Seal Packing Thickness |
| *5 | Seal Packing Width | *6 | Protrusion |
| Area | Seal Packing Diameter | Distance from Edge of Cover to Center of Seal Packing | Seal Packing Application Length | Protrusion from Cylinder Head |
|---|---|---|---|---|
| A - A
(Dashed line) |
2.5 to 4.0 mm (0.0984 to 0.157 in.) | 2.0 mm (0.0787 in.) | - | - |
| B - B
(Continuous line) |
10 to 14 mm (0.394 to 0.551 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick | 6.0 mm (0.236 in.) | 46 mm (1.81 in.) from top of bolt hole | - |
| C - C
(Continuous line) |
10 to 14 mm (0.394 to 0.551 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick | 6.0 mm (0.236 in.) | 54 mm (2.13 in.) from top of bolt hole | - |
| D - D
(Continuous line) |
9.0 to 13 mm (0.354 to 0.512 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick | - | 13 mm (0.512 in.) from top of bolt hole | - |
| E - E
(Continuous line) |
9.0 to 13 mm (0.354 to 0.512 in.) wide and 2.5 to 4.0 mm (0.0984 to 0.157 in.) thick | - | 13 mm (0.512 in.) from top of bolt hole | - |
| I - I
(Continuous line) |
8.0 mm (0.315 in.) | - | 56.5 mm (2.22 in.) from bottom of cylinder head | 2.0 to 3.0 mm (0.0787 to 0.118 in.) |
| J | 10 mm (0.394 in.) | - | 20 mm (0.787 in.) | - |
Remove any oil from the contact surface.
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the timing chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Do not start the engine for at least 4 hours after the installation.
| *1 | Drive Rotor Spline |
| *2 | Crankshaft Timing Gear |
Align the drive rotor spline of the oil pump and crankshaft timing gear as shown in the illustration.
Temporarily install the timing chain cover with the 19 bolts and 2 nuts.
| *1 | Area 1 | *2 | Area 2 |
| *3 | Area 3 | *4 | Area 4 |
| *5 | Nut | - | - |
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 75 mm (2.95 in.) | 10 mm (0.394 in.) |
| Bolt B | 75 mm (2.95 in.) | 8 mm (0.315 in.) |
| Bolt C | 90 mm (3.54 in.) | 8 mm (0.315 in.) |
| Bolt D | 95 mm (3.74 in.) | 8 mm (0.315 in.) |
| Bolt E | 35 mm (1.38 in.) | 8 mm (0.315 in.) |
| Bolt F | 75 mm (2.95 in.) | 10 mm (0.394 in.) |
Excluding the bolts labeled A and F, tighten the bolts and nuts in this order: Area 1, Area 3, Area 2.
Tighten the bolts labeled A in this order: Area 2 and Area 3.
Tighten the bolts labeled F.
Tighten the bolts labeled E in Area 4.
Apply adhesive to the timing chain cover plug.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Using a 10 mm socket hexagon wrench, install the timing chain cover plug.
3.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
4.INSTALL FRONT CRANKSHAFT OIL SEAL
5.INSTALL CRANKSHAFT POSITION SENSOR
6.INSTALL OIL PAN SUB-ASSEMBLY
Install a new O-ring.
Apply seal packing in a continuous line as shown in the illustration.
| *1 | Seal Packing | - | - |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| Area | Seal Packing Diameter | Distance from Edge of Cover or Center of Bolt Hole to Center of Seal Packing |
|---|---|---|
| A - A and C - C | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | 8.0 mm (0.315 in.) |
| B - B | 2.0 to 3.0 mm (0.0787 to 0.118 in.) | 6.5 mm (0.256 in.) |
Remove any oil from the contact surface.
Install the oil pan within 3 minutes after applying seal packing.
Do not start the engine for at least 4 hours after the installation.
|
Bolt A |
|
Bolt B |
|
Nut |
Temporarily install the oil pan with the 16 bolts and 2 nuts.
| Item | Length |
|---|---|
| Bolt A | 20 mm (0.787 in.) |
| Bolt B | 40 mm (1.57 in.) |
Uniformly tighten the 16 bolts and 2 nuts in the order shown in the illustration.
7.INSTALL OIL STRAINER SUB-ASSEMBLY
Install a new gasket and the oil strainer with the bolt and 2 nuts.
8.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
| *1 | Seal Packing |
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| Seal Packing Diameter | Distance from Edge of Cover or Center of Bolt Hole to Center of Seal Packing |
|---|---|
| 2.5 to 3.5 mm (0.0984 to 0.138 in.) | 6.0 mm (0.236 in.) |
Remove any oil from the contact surface.
Install the oil pan within 3 minutes after applying seal packing.
Do not start the engine for at least 4 hours after the installation.
Temporarily install the No. 2 oil pan with the 20 bolts and 2 nuts.
|
Bolt |
|
Nut |
Uniformly tighten the 20 bolts and 2 nuts in the order shown in the illustration.
Install a new gasket and the drain plug.
9.INSTALL CRANKSHAFT PULLEY
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
Using SST, install the crankshaft pulley bolt.
Do not reuse the pulley bolt.
10.INSTALL CAMSHAFT POSITION SENSOR
11.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Install 2 new cover gaskets to the head cover.
|
Seal Packing |
Apply seal packing to the places shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
4.0 mm (0.157 in.)
Remove any oil from the contact surface.
Install the head cover within 3 minutes after applying seal packing.
Do not start the engine for at least 4 hours after the installation.
Temporarily install the cylinder head cover with the 19 bolts and 2 nuts.
Uniformly tighten the 19 bolts and 2 nuts in the order shown in the illustration.
In numerical order, confirm that the bolts labeled 1 to 8 are tightened to the specified torque. Tighten the bolts as necessary.
12.INSTALL OIL FILLER CAP SUB-ASSEMBLY
13.INSTALL NO. 1 WATER BY-PASS PIPE
14.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
15.INSTALL THERMOSTAT
16.INSTALL WATER INLET
17.INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
18.INSTALL GENERATOR ASSEMBLY
19.INSTALL INTAKE MANIFOLD
20.INSTALL FUEL INJECTOR ASSEMBLY
21.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY
22.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
23.INSTALL PCV PIPE
24.INSTALL SPARK PLUG
25.INSTALL IGNITION COIL ASSEMBLY
26.REMOVE ENGINE FROM ENGINE STAND
27.INSTALL ENGINE ASSEMBLY