Home › Engine / Hybrid System › 2TR-FBE LUBRICATION › OIL PUMP › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009601 2TR-FBE LUBRICATION _0052406 OIL PUMP A

2TR-FBE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 7.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 11.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

Hide 12.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 15.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

Hide 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A101292

Remove the 19 bolts, 2 nuts, cylinder head cover and 2 gaskets.


Hide 20.REMOVE CRANKSHAFT PULLEY

A302678C01
1.844,4.083 2.531,4.083 true 0.896,2.531 1.292,3.333 1.292,3.333 2.417,2.542 true 2.458,2.76 2.656,2.333 2.656,2.333 2.823,2.333 true 1.021,0.969 1.323,1.375 1.323,1.375 1.073,0.729 true 2.698,1.083 2.219,1.354 2.219,1.354 2.688,0.844 true 0.396,0.208 1.313,0.406 0.917,0.198 10 false 13°47' 2.021,1.333 2.188,1.521 0.167,0.188 10 true *1 1.24,1.406 1.448,1.573 0.208,0.167 10 true *1 1.188,3.375 1.458,3.573 0.271,0.198 10 true *1 2.885,2.229 3.354,2.417 0.469,0.188 10 true 6°37' 2.583,4 2.854,4.198 0.271,0.198 10 true *2
*1 Timing Mark
*2 Groove


a.

Turn the crankshaft pulley, and align its groove with timing mark 0 of the timing chain cover.


b.

Check that the timing marks of the camshaft timing gear and sprocket are aligned with the timing marks of the No. 1 bearing cap, as shown in the illustration.


c.
A302679C01
0.927,1.146 0.531,0.76 0.531,0.76 1.01,0.906 true 0.521,1.854 0.833,2.01 0.313,0.156 10 false *a 1.542,1.896 1.854,2.052 0.313,0.156 10 false *b 0.229,0.635 0.688,0.833 0.458,0.198 10 false SST
*a Loosen
*b Hold


Using SST, loosen the pulley bolt.

SST
09213-54015  (91651-60855)
09330-00021  


d.
G035121C01
0.677,1.375 0.917,1.375 0.917,1.375 1.167,1.208 false 1.344,1.938 1.521,2.115 0.177,0.177 10 false *a 0.375,1.281 0.677,1.469 0.302,0.188 10 false SST 0.417,0.625 0.615,0.792 0.198,0.167 10 false *b
*a Loosen
*b Hold


Using SST, remove the pulley bolt and pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05021)


Hide 21.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove the drain plug and gasket.


b.

Remove the 20 bolts and 2 nuts.


c.
A099215

Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:

Be careful not to damage the contact surfaces of the oil pans.



Hide 22.REMOVE OIL STRAINER SUB-ASSEMBLY

a.

Remove the bolt, 2 nuts, oil strainer and gasket.


Hide 23.REMOVE OIL PAN SUB-ASSEMBLY

a.

Remove the 16 bolts and 2 nuts.


b.
G036411C02
0.552,1.313 0.844,1.313 0.844,1.313 1.771,1.51 true 0.344,1.229 0.51,1.406 0.167,0.177 10 false *1
*1 Protective Tape


Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.


HINT:

Tape the screwdriver tip before use.



c.

Remove the O-ring.


Hide 25.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
G036504

Remove the 19 bolts and 2 nuts shown in the illustration.


b.
G037273C01
0.26,0.188 0.375,0.188 0.375,0.188 0.729,0.479 true 3.094,1.271 2.979,1.271 2.979,1.271 2.698,0.646 true 0.542,3.021 1.24,3.021 true 2.24,3.208 2.375,3.208 2.375,3.208 2.948,2.771 true 0.094,0.094 0.26,0.26 0.167,0.167 10 false *1 3.167,1.156 3.396,1.333 0.229,0.177 10 false *1 1.292,2.906 1.458,3.073 0.167,0.167 10 false *1 2.052,3.104 2.219,3.271 0.167,0.167 10 false *1
*1 Protective Tape


Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head, cylinder block and timing chain cover.


HINT:

Tape the screwdriver tip before use.



c.
A302630

Remove the 3 O-rings.


d.
G036021

Using a 10 mm socket hexagon wrench, remove the timing gear case plug.


Hide 26.REMOVE ENGINE WATER PUMP ASSEMBLY

a.
A087223

Remove the 8 bolts, engine water pump and gasket.


Hide 27.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A302631C01
1.073,1.76 0.594,1.781 0.594,1.781 0.729,1.427 false 1.427,0.844 1.771,0.292 1.771,0.292 1.948,0.292 true 2.031,0.198 2.344,0.396 0.313,0.198 10 false *1 0.448,1.802 0.76,2 0.313,0.198 10 false *2
*1 Protective Tape
*2 Wooden Block


Place the timing chain cover on wooden blocks.


b.

Using a screwdriver pry out the front crankshaft oil seal.

HINT:

Tape the screwdriver tip before use.