Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL PUMP › from 2012.10
RM1840EF _51 Engine / Hybrid System _009602 1GR-FE LUBRICATION _0052411 OIL PUMP A

1GR-FE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 5.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

Hide 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 10.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 13.REMOVE CRANKSHAFT PULLEY

a.
A072947
1.448,1.427 1.719,1.854 1.719,1.854 2.302,1.854 true 1.542,0.958 2.083,1.854 true 2.344,1.771 2.656,1.948 0.313,0.177 10 false SST 2.969,0.813 3.167,1.01 0.198,0.198 10 false *a 0.875,1.938 1.052,2.104 0.177,0.167 10 false *b
*a Hold
*b Loosen


Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  (91651-60855)
09330-00021  


b.
A072948
1.365,1.021 1.01,0.406 1.01,0.406 0.844,0.406 false 0.531,0.313 0.865,0.531 0.333,0.219 10 false SST 0.448,1.26 0.635,1.458 0.188,0.198 10 false *a 2.448,1.823 2.635,2.021 0.188,0.198 10 false *b
*a Hold
*b Loosen


Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05031)


Hide 14.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

a.
A251899
1.708,1.958 1.74,1.927 false
V100135

Bolt
V100136

Nut


Remove the 14 bolts and 2 nuts.


b.
A112957

Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.

NOTICE:
·

Be careful not to damage the contact surfaces of the oil pan and No. 2 oil pan.

·

Be careful not to damage the No. 2 oil pan flange.




Hide 15.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A112955

Remove the bolt, 2 nuts, oil strainer and gasket.


Hide 16.REMOVE OIL PAN SUB-ASSEMBLY

a.
A251900
0.656,1.885 0.667,1.938 false
V100135

Bolt
V100136

Nut


Remove the 17 bolts and 2 nuts.


b.
A112954

Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and oil pan.



c.
A076452

Remove the O-ring from the timing chain cover.


Hide 17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A251906
0.583,1.448 0.583,1.5 false
V100135

Bolt
V100136

Nut


Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


Hide 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A251905
0.542,1.896 0.5,1.958 false
V100135

Bolt
V100136

Nut


Remove the 10 bolts, 3 seal washers, 2 nuts, cylinder head cover and gasket.


Hide 20.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A251960
1.135,1.698 1.208,1.656 false
V100135

Bolt
V100136

Nut


Remove the 3 bolts, 2 nuts, oil filter bracket and gasket.


Hide 21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A251901
0.844,2.604 0.896,2.594 false
V100135

Bolt
V100136

Nut


Remove the 24 bolts and 2 nuts.


b.
G038102

Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.


HINT:

Tape the screwdriver tip before use.



c.
A134563

Remove the O-ring from the cylinder head for bank 2.


Hide 22.REMOVE FRONT CRANKSHAFT OIL SEAL

a.

If the timing chain cover is removed:

i.

Using a screwdriver and wooden block, pry out the oil seal.

NOTICE:

Do not damage the surface of the oil seal press fit hole and crankshaft.


HINT:

Tape the screwdriver tip before use.